···
Log in / Register

How do I enable the child safety lock on my Concept ETV9460bc oven?

1Answers
LincolnAnn
12/17/2025, 12:44:21 PM

To activate the child lock on your Concept ETV9460bc Built-In Multifunctional Electric Oven, follow these simple steps to enhance your kitchen's safety: First, locate the light and child lock on/off button (usually labeled with a relevant symbol). Next, press and hold this button for three seconds. You will hear an audible signal, and the child lock icon will appear on the display, confirming that the oven is now locked. To disable the child lock, repeat the process: press and hold the same button for three seconds. Another audible signal will sound, and the child lock icon will disappear, indicating the oven is unlocked and ready for use. This feature ensures peace of mind, keeping your children safe around your Concept ETV9460bc oven.

Was this review help?
109
Share
More Q&A

How do I enable the child safety lock on my Concept ETV9460bc oven?

To activate the child lock on your Concept ETV9460bc Built-In Multifunctional Electric Oven, follow these simple steps to enhance your kitchen's safety: First, locate the light and child lock on/off button (usually labeled with a relevant symbol). Next, press and hold this button for three seconds. You will hear an audible signal, and the child lock icon will appear on the display, confirming that the oven is now locked. To disable the child lock, repeat the process: press and hold the same button for three seconds. Another audible signal will sound, and the child lock icon will disappear, indicating the oven is unlocked and ready for use. This feature ensures peace of mind, keeping your children safe around your Concept ETV9460bc oven.
109
Share

How do I install the Saddle Tramp BC-AMP06 amp bracket on my 2014 or newer Harley Davidson Street Glide or similar model?

Installing the Saddle Tramp BC-AMP06 Amp Mounting Bracket on your Harley-Davidson Street Glide, Electra Glide, Ultra, or Limited model from 2014 and up is straightforward. Here's a step-by-step guide: First, you'll need to disassemble the fairing. Begin by removing the four T-27 screws from the inner fairing. Next, carefully remove the three T-27 screws securing the windshield. Then, detach the outer fairing, remembering to disconnect the headlight. Take out the fairing vent by removing its two T-27 screws. Second, install the BC-AMP06 bracket. Remove the four upper bolts from the Radio support Bracket using a T25 Torx bit. Position the BC-AMP06 mount into the radio cradle. Be sure not to overtighten the fasteners; the factory specification is 20 In. Lbs. Finally, reassemble the fairing by reversing the disassembly steps. The kit also includes 12 black zip ties and an 8.5”x6” hook and loop tape to help you secure and organize cables. The instruction manual provides more detailed guidance if needed.
116
Share

How do I grease bushings and sleeves for my FABTECH Uniball Suspension Kit's control arms?

To properly grease the bushings and sleeves before installing them in your FABTECH FTS21289 2021 GM SUV 4WD 3 Inch Uniball UCA Suspension Kit control arms, follow these steps: First, gather your components, including the new Fabtech control arms, two FT1038 bushings, two FT1037 bushings, two FT84 grease zerks, and two FT626 sleeves. Next, use the provided grease packet (FTLUBE) to apply grease generously to both the bushings and the sleeves. Ensure complete coverage by coating the entire surface area of the bushings and sleeves with grease. This lubrication is essential for smooth operation. Once adequately greased, install the components into the control arm, referencing the detailed installation instructions within your kit's manual.
120
Share

What's the best way to fix sticking doors and drawers on my Evolur Cape May 896 Dresser?

Dealing with sticking doors and drawers on your Evolur 896 Cape May Dresser? It's a common issue, often due to changes in humidity and temperature. Here's how to tackle it, according to the Evolur manual: First, be patient. The wood may adjust naturally as conditions stabilize. If the problem continues, try a dehumidifier to control humidity in the room. This can reduce swelling. Finally, applying wax, like candle wax or paraffin, to the sides of the sticking doors and drawers can provide lubrication, making them easier to open and close. Following these steps should help keep your Evolur dresser functioning smoothly.
111
Share

How do I properly clean and maintain my SIGURO SGR-MP-X600S Multifunction Pressure Cooker?

Maintaining your SIGURO SGR-MP-X600S Multifunction Pressure Cooker is crucial for both its lifespan and your safety. Here's a straightforward guide to cleaning and maintenance, mirroring the manufacturer's recommendations: Exterior Cleaning: Wipe the exterior surfaces of the appliance with a soft sponge slightly moistened with warm water. Dry with a clean cloth. Inner Pot Care: Wash the inner pot using warm water and a small amount of dish soap. Rinse thoroughly and dry completely. Lid Cleaning: The lid comprises three parts: the outer lid, the inner lid, and the seal. To clean: Invert the outer lid and detach the inner lid by the central pin. Carefully remove the silicone seal band from the inner lid's edge. Clean all lid components after each use. Valve Inspection: Regularly check the safety and pressure valves to ensure they are clean and operating correctly. The safety valve should move freely. Storage Procedures: Prior to storage, ensure the appliance and all its accessories are clean and completely dry. Store them in a cool, dry, and well-ventilated area, away from children and pets. Troubleshooting Tips: If issues arise, consult the troubleshooting section in your SIGURO SGR-MP-X600S manual. For instance, if you notice steam or water leaking from the lid, verify the silicone seal is correctly positioned, clean, and not worn. Disposal Guidelines: When the time comes to dispose of your pressure cooker, adhere to the disposal instructions detailed in the manual to ensure environmentally responsible practices. Following these cleaning and maintenance steps will help keep your SIGURO SGR-MP-X600S Multifunction Pressure Cooker in excellent condition, ensuring safe and efficient cooking for years to come.
113
Share

How do I connect and configure the Solid State Instruments RTR-22+ High-Speed Relay?

Connecting and configuring the Solid State Instruments RTR-22+ High-Speed Water and Gas Meter Relay involves several key steps. First, the RTR-22+ can be mounted in any position. For power input, if using a 120VAC supply, connect the hot lead to the L1 terminal and neutral to the NEU terminal. For a 277VAC supply, connect the hot lead to the L2 terminal and neutral to the NEU terminal. Always connect the GND terminal to Ground. If a neutral connection is unavailable, connect both the NEU and GND terminals to Ground. An inline fuse is also recommended. Next, consider the meter connections. The RTR-22+ has two 2-Wire (Form A) inputs. Connect the Kin1 and Yin1 terminals to the first meter's K and Y terminals, and Kin2 and Yin2 to the second meter's K and Y terminals. The Yinx terminals provide a +13VDC wetting voltage to the meter's Y dry contact output. Each input has a Yellow LED indicating its status. Regarding relay input and output configuration, the RTR-22+ features input and output configuration switches. The input debouncing time can be set to 50uS, .5mS, 5mS, or 20mS. The outputs are dry-contact outputs, with a Green LED indicating output status. The RTR-22+ offers both "Normal" and "Fixed" pulse output modes. The Normal mode mirrors input pulse widths, while the Fixed mode uses a pre-set pulse width. Finally, configure the relay. Input filter times can be set to 50uS, .5mS, 5mS, or 20mS, while output times are independently selectable for each channel: 50mS, 100mS, 200mS, or 500mS. Refer to the Solid State Instruments RTR-22+ manual for detailed instructions and specific application needs.
105
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.