···
Log in / Register

What is the trick for pulling over in Subject 3 of the driving test?

1Answers
ThomasDella
09/04/2025, 12:52:51 AM

When pulling over, turn on the right turn signal, then release the accelerator and reduce speed according to the actual situation while observing the right rearview mirror. Distance from the curb: After confirming it is safe behind, slightly turn the vehicle to the right, adjust slightly to the right side, align the front one-third of the car with the edge line of the right lane, and straighten the body. Slowly brake to stop the vehicle when it is about 30cm away from the edge line. Precautions for pulling over: When pulling over, first observe whether there are other high-speed vehicles around, promptly turn on the right turn signal, and slowly pull over to the right side.

Was this review help?
109
Share
More Q&A

Why does the car make a squeaking sound when starting?

Car starting with a squeaking sound is usually caused by a loose timing belt or an abnormal timing belt. The timing belt is an important component of the engine system. It connects to the crankshaft and works with a certain transmission ratio to ensure the timing of engine intake and exhaust, thus maintaining normal engine operation. The reason why cars use belts for transmission instead of gears is that belts produce less noise and provide precise transmission. Under high-temperature operating conditions of the engine, incorrect matching and installation of the timing belt tensioner can affect the service life of the timing belt. During the car's starting process, whether it's a cold start or a normal temperature start, if a squeaking sound occurs, the timing belt should be replaced promptly.
111
Share

Where are the A-pillar and B-pillar located in a car?

The positions of the A-pillar and B-pillar in a car are as follows: the A-pillar is located between the engine compartment and the passenger compartment, above the left and right rearview mirrors; the B-pillar is situated between the front and rear seats of the passenger compartment, extending from the roof to the bottom of the car. Both the A-pillar and B-pillar are part of the car's body frame, which protects the occupants in the event of a collision. In the structural design of a car, the position and shape of the A-pillar and B-pillar are related to the overall layout, safety, and driving comfort of the vehicle. They not only support the roof of the passenger compartment but also play a crucial protective role for the occupants inside. In the event of a rollover or overturn, they effectively prevent the passenger compartment from being crushed or deformed.
106
Share

What is the Correct Method for Starting a Car?

Correct car starting method is: 1. Fully depress the clutch, turn the ignition key to the ON position, wait for 5 to 8 seconds, then turn the key to the start position to ignite the engine; 2. Once the engine starts smoothly, immediately release the ignition key to let it automatically return to the ON position. Car starting precautions: Do not press the accelerator when starting. Before the key is turned to the ON position for power, the engine's idle motor, throttle sensor, oxygen sensor, temperature sensor, and a series of other sensors are not powered. When these sensors are powered, they will automatically adjust and adapt to an optimal position and parameters under the guidance of the computer based on the state of various engine components. This automatic adjustment and adaptation often require a certain amount of time.
110
Share

What Are the Causes of Steering Wheel Vibration?

The causes of steering wheel vibration: 1. When driving at speeds between 80 to 90 km/h, the steering wheel vibrates, but returns to normal when exceeding 90 km/h: This is caused by deformation or issues in the vehicle's drivetrain; 2. Steering wheel vibration when encountering bumpy roads: This occurs due to loose ball joints, detached rubber bushings at connection points, or irregular tire wear during driving; 3. Sudden steering wheel vibration during high-speed driving: This results from excessive or frequent braking, causing the brake discs and pads to overheat and deform upon cooling; 4. Steering wheel vibration when stationary: This is caused by aging engine mounts and rubber components at connection points.
119
Share

What Causes a Car with Power to Fail to Start?

The reasons why a car has power but fails to start are: 1. The steering wheel is locked; 2. Insufficient fuel in the car; 3. The car battery is depleted; 4. Incorrect connection of the positive and negative terminals; 5. Wrong gear selection; 6. Starter motor malfunction; 7. Excessive carbon buildup in the throttle; 8. Faulty crankshaft position sensor. Solutions for a car with power that fails to start: 1. Check the battery power level; if insufficient, replace the battery or charge it promptly; 2. Check if oil flow is obstructed, move the car to a warmer location to raise the temperature, enhance maintenance, and change the oil in a timely manner; 3. Drain any accumulated water in the exhaust pipe; 4. Inspect the condition of the antifreeze; 5. Clean the fuel lines promptly and replace the fuel filter.
119
Share

How to Remove Fog from Car Windows?

Methods to remove fog from car windows include: 1. Preventive measures like spraying anti-fog agents. Spray a small amount of defogger on the car windows and wipe it clean to remove dirt and stains from the glass; 2. Air conditioning cooling method. Use the air conditioning's dehumidification function to reduce air humidity and eliminate fog; 3. Air conditioning heating method. Reduce the temperature difference to remove condensation. Note that whether the air conditioning is automatic or manual, turning it on helps with dehumidification. Avoid setting the air conditioning temperature to the coldest position, as prolonged use may cause frost to form on the outer side of the windshield.
101
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.