How to Deal with Seat Belt Not Retracting?

1 Answers
CooperDella
07/25/25 1:24pm
Seat belt not retracting can be handled by the following methods: 1. The owner can use dishwashing liquid or some cleaning agents to clean it thoroughly; 2. Remove the fixing bolt and add a spring washer to keep the slide buckle away; 3. Open the decorative panel, clean the debris and dust near the roller, and then use some cleaning agents to wash it. The reasons are: 1. Excessive dirt accumulation at the contact point between the seat belt webbing and the B-pillar seat belt buckle; 2. The slide buckle component of the seat belt is too close to the B-pillar, causing the seat belt retractor and the seat belt webbing not to be in a straight line; 3. The lower roller of the seat belt is obstructed during retraction, preventing normal retraction.
Was this review help?
15
1
Share
More Forum Discussions

What to Do If 95 and 92 Gasoline Are Mixed?

Mixing 95 and 92 gasoline once or twice will not have much impact, but it should not be used for a long time. Long-term mixing of different grades of gasoline will affect the service life of the car's ignition system, fuel injector, and spark plug, and advance the overhaul time of the vehicle. The following is a related introduction about gasoline grades: 1. The commonly mentioned 92 or 95 gasoline grades do not represent the quality or purity of the gasoline, but rather the anti-knock index of the gasoline. 2. There is a component in gasoline called isooctane. The mentioned 92 or 95 refers to the octane number in the gasoline. The higher the content, the stronger the anti-knock property of the gasoline. Under the same conditions, the anti-knock index of 95 gasoline is stronger than that of 92 gasoline.
10
1
Share

How Long Does It Take for a Paint Protection Film to Fully Dry?

It takes at least half a month for a paint protection film to fully dry. Below is an introduction to paint protection films: 1. Introduction: A paint protection film is a high-performance, eco-friendly film widely used in the automotive beauty and maintenance industry. It is commonly known as a transparent paint protection film. With excellent toughness, it isolates the car's paint from the air after installation, providing long-lasting protection. 2. Features: (1) Superior elasticity and strong tensile strength. (2) Anti-yellowing properties for over 3 years and anti-aging properties for over 5 years. (3) Crystal-clear transparency that blends seamlessly with the original car paint without affecting its color. (4) Resistant to damage from petroleum, grease, weak alkali, gravel, acid rain, etc. (5) Exceptional softness and memory properties that protect against minor scratches and friction.
8
2
Share

What is the minimum ground clearance of the Baojun 730?

The minimum ground clearance of the Baojun 730 is approximately 160mm when fully loaded. Additional details about the Baojun 730 are as follows: 1. Overview: The Baojun 730 is a 7-seat family car customized by SAIC-GM-Wuling for 'China's big families' based on the needs of millions of users. It was officially launched in March 2019 and includes two models: the 1.5T-CVT Fashion and the 1.5T-CVT Flagship. The vehicle offers high driving smoothness and comfort. 2. Other specifications: The vehicle dimensions are 4780×1820×1755mm. The trunk volume is 261 liters. The fuel consumption ranges from 6.3-8.0L/100km. The fuel tank capacity is 52 liters. The engine type is a naturally aspirated engine. The standard seating capacity is 7. The top speed is 160km/h. The acceleration time is 18 seconds (0-100km/h). The curb weight is 1410 kg.
5
2
Share

Why does the car not accelerate when stepping on the gas?

The reasons why the car does not accelerate when stepping on the gas are as follows: 1. Check the fuel pressure, cleanliness, and replace the fuel filter. 2. Inspect the ignition system, spark plug wires, spark plugs, etc. 3. Check the cylinder pressure and whether the engine is misfiring. 4. Inspect if the intake and exhaust pipes are unobstructed (clogged catalytic converter). 5. Verify if the ignition timing is correct, including the throttle position sensor and idle control motor. 6. Poor fuel quality. Relevant information is as follows: 1. The accelerator pedal, also known as the gas pedal, is part of the car's fuel supply system. By controlling the amount of pedal depression, it regulates the throttle opening, controls the air intake, and the computer adjusts the fuel quantity, thereby controlling the engine speed. 2. The throttle of a car engine is typically controlled by the pedal, which is the device used to regulate the fuel supply. The operation of the accelerator pedal should use the right heel placed on the floor of the driver's compartment as a pivot, with the ball of the foot gently pressing on the accelerator pedal, using the ankle joint's extension and flexion to press down or release. When operating the accelerator pedal, the force should be gentle, ensuring smooth and gradual movements.
8
1
Share

What does the 'P plus △' symbol mean in the BMW 5 Series?

Reverse parking sensor, also known as 'reverse collision avoidance radar' or 'parking assist device', mainly consists of ultrasonic sensors, controllers, and displays. More information about the BMW 5 Series is as follows: 1. Overview: The domestic 5 Series is a premium sedan, with the current generation introduced in 2004. The BMW 5 Series is one of the most outstanding series in automotive history, with its peak era beginning with the third-generation E34 (1988-1996). The current 5 Series is the third-generation product of the E34. 2. Others: The top speed is 250km/h. The seat material is genuine leather. The acceleration time is 8.6 seconds (0-100km/h). The drivetrain is front-engine, rear-wheel drive. The body weight is 1740KG. The number of valves is 24. The standard transmission is an 8-speed automatic with manual mode. The maximum power is 190KW/rpm. The maximum torque is 400Nm/rpm.
20
5
Share

What to Do When the Remote Car Key Gets Wet?

When the remote car key gets wet, there are several ways to handle it: 1. Disassemble the key, wipe the chip and battery with anhydrous alcohol, and then dry it with a hair dryer: Use a cotton swab dipped in anhydrous alcohol to clean the circuit board. Alcohol with a concentration of 95% available at pharmacies can be used. Anhydrous alcohol has strong water absorption properties, preventing the chip in the remote key from short-circuiting and burning out. 2. Completely separate the two parts of the remote. Wipe the internal components with highly absorbent paper towels: If water is not thoroughly removed, it can cause oxidation and corrosion of the circuit board. Use highly absorbent paper towels to clean the internal parts, and avoid pressing any remote functions during this process. 3. Get a new key: You can have a new key made at a specialized key-cutting stall or visit a 4S dealership. By examining the engine chip inside the key and retrieving the records, a new key can be matched.
5
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.