How much can you actually drive with a speed limit of 120?

Why does the Audi Q5 shake when hot but not when cold?

Audi Q5 shaking when hot is mainly caused by an inappropriate air-fuel mixture, carbon deposits on the valves and intake ports, and uneven cylinder conditions. Specific explanations include the following three reasons: Inappropriate air-fuel mixture: The air-fuel mixture ratio is not accurately adjusted, which occurs in both open-loop and closed-loop control systems. In vehicles with closed-loop control, the minimum operating temperature of the oxygen sensor is 370 degrees Celsius. Carbon deposits on the valves and intake ports: If carbon deposits accumulate on the valves and intake ports inside the engine, the ECU may make incorrect judgments because the carbon deposits can absorb a certain amount of fuel. Uneven cylinder conditions: After prolonged use of the engine, the gaps between each cylinder liner and piston can vary in size, meaning some gaps are larger while others are smaller. Solutions: Whether it's a cold start or restarting after a short stop, generally after disconnecting the power for a few minutes, each time you start the engine, first turn on the power for 3-5 seconds to allow the fuel pump to supply fuel and the oil pump to build up pressure. Ensure all sensors receive signals before ignition.

111

Share

Why don't the Nissan Teana's small lights turn on?

The reasons for the failure of the car's small lights not turning on are switch issues, socket issues, and wiring faults. Switch issues: When the car's small lights don't turn on, multiple checks should be performed. First, turn on the small light switch and check whether the voltage at the bulb's two electrodes is normal. If there is no voltage, inspect the switch and connectors. Socket issues: Connect the socket and check whether the small lights turn on. If there are no issues, proceed to inspect the wiring. Bulb wiring fault issues: Remove the tail light bulb and check whether the filament is burnt out. If the filament is intact, use a test pen or screwdriver to scrape the tail light's live wire terminal against the metal to check for sparks. If there are no sparks, it indicates an open circuit in the tail light wiring. Locate the open circuit and reconnect the wire. If there are sparks, it indicates poor grounding of the tail light.

105

Share

What are the essential maintenance items for the second service of a BMW 530?

For the second maintenance of a BMW, replace the engine oil and oil filter, and check if the air filter needs replacement. The specific maintenance should be carried out according to the vehicle's maintenance manual. If there are no abnormalities with the vehicle, replacing the engine oil is sufficient. Maintenance can also be chosen based on the mileage driven. At 20,000 kilometers: The essential maintenance items at 20,000 kilometers include replacing the engine oil, oil filter, air filter, cabin air filter, and performing tire rotation with four-wheel dynamic balancing. If it's at 20,000 kilometers: For the vehicle's second maintenance (if it's at 20,000 kilometers), in addition to the same items as the first maintenance—replacing the engine oil and oil filter—the air filter and cabin air filter can also be replaced.

117

Share

Where is the engine number located on a Mercedes ML350?

The engine number of the Mercedes ML350 is located under the front passenger seat. Adjust the power seat to its rearmost position, and you will find a small opening on the floor mat—pry it open to reveal the engine number. It typically consists of a combination of 7 to 8 digits and letters. In addition to the method mentioned above, the engine number can also be found through the following four ways: The vehicle's driving license displays the engine number, usually located on the second-to-last line; The motor vehicle registration certificate records the engine number; The purchase invoice includes the engine number; The vehicle purchase tax payment certificate states the engine number. It's important to note that the engine number is not the same as the engine model. The engine model refers to the specifications and size of the engine within the manufacturer's lineup, and multiple engines can share the same model. On the other hand, the engine number is the production serial number of the engine—each engine has a unique number, and no two engines share the same engine number.

115

Share

Where is the fuse for the reversing camera of Audi A6L located?

Audi A6 has two fuse boxes, one is located on the side when the driver's door is opened, and the other is inside the right side of the trunk when opened. Tips for replacing fuses: If there is no spare fuse for the Audi A6, you can use other idle fuses as substitutes. For example, if the fuse for the window is blown and there happens to be no spare fuse, you can use fuses from idle components like the audio system or air conditioning, provided that their ampere ratings are the same or smaller than the original fuse. Usage precautions: For the Audi A6, you don't need to remove fuses directly by hand. Each fuse box is equipped with a pair of pliers for removing fuses. Both ends of the pliers can be used to remove large and small fuses.

114

Share

At how many kilometers does the BMW Mini require its first maintenance?

The first maintenance should be performed between 8,000 to 10,000 kilometers. First maintenance inspection items: The primary focus of the first maintenance is to check the vehicle's break-in and wear condition. The main tasks include changing the engine oil and oil filter, followed by cleaning the air filter, checking tire pressure, testing the engine and transmission speeds, and inspecting the functionality of lights to eliminate potential safety hazards. Engine oil replacement method: Start the vehicle for about one minute to allow the oil to circulate and warm up, then turn off the engine. Open the oil cap, use tools to loosen the oil filter and oil drain plug, place an oil pan, and then remove the drain plug to drain the old oil. After all the oil has drained, re-tighten the drain plug, clean any excess oil around it with a cloth, and then remove the old oil filter with a cloth underneath. Apply oil to the new filter's sealing ring, reinstall it in its original position by turning it clockwise, then add new oil through the oil filler port to the standard level, and finally tighten the oil filler cap. Note: After adding the oil, start the engine and observe for 1-2 minutes to check for any oil leaks. If any leaks are detected, immediately turn off the engine and inspect the issue.

120

Share