Can Winter Tires Run at 120 km/h on Highways?

Where is the Bluetooth button on the old Volkswagen Polo?

The vehicle management office requires the examinee to cancel the exam in person. The following is an introduction to the content related to Subject 2: 1. Exam requirements: The requirement for parallel parking is that the driver must park the vehicle in the right parking space without the wheels touching the lane boundary or the parking space boundary. 2. Content and requirements of Subject 2: The five assessment items are reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving on a curve. Subject 2 requires 26 class hours, including 2 hours of theoretical knowledge, so the actual practice is 24 hours. Below is extended information about the content of Subject 3: 1. Starting: Preparing to drive, starting, and driving straight. 2. Speed control: Shifting gears, changing lanes, and pulling over. 3. Turning: Going straight through an intersection, turning left at an intersection, and turning right at an intersection. 4. Passing designated areas: Passing through pedestrian crossings, school zones, and bus stops. 5. Vehicle control: Meeting other vehicles, overtaking, making U-turns, and driving at night.

110

Share

What are the reasons for poor performance in S-curve practice?

S-curve practice is challenging because the S-curve is relatively difficult. The S-curve is one of the items in the C1 driver's license test, specifically in Subject 2. Maintain slow speed: When entering the curve, keep the speed slow. If the speed is too fast, gently apply the foot brake, but do not come to a complete stop. Keep the car body to the right: When initially entering the curve, try to keep the car body close to the right-side boundary line. Correct use of the steering wheel: For the first curve, which turns left, turn the steering wheel one full turn plus 45 degrees to the left when the left corner of the car touches the right line. Maintain a certain distance: Keep the left corner of the car at a certain angle relative to the line on the ground to ensure the car does not cross or go out of the line.

111

Share

Why does the car air conditioner turn on and off intermittently?

The compressor turns on and off intermittently because it automatically starts or stops based on the set temperature, rather than running continuously. This intermittent operation is a protective phenomenon of the compressor, representing the recovery time of the compressor's thermal protector. Typically, this takes only a dozen to several dozen minutes, but these values may change after prolonged use of the compressor. The main reasons for this protection are threefold: 1. Lack of refrigerant: Insufficient refrigerant in the system causes the compressor's exhaust temperature to trigger thermal protection. Even if there are white bubbles at the needle point, it only indicates the presence of refrigerant in the system, but the amount and whether there is a shortage cannot be determined. 2. High exhaust pressure: Excessive exhaust pressure from the compressor increases the operating current, leading to current thermal protection. There are many possible causes, such as poor ventilation of the external heat exchanger, a dirty or clogged heat exchanger, or a faulty external fan motor, any of which could result in this situation. 3. Faulty thermal protector: A malfunctioning thermal protector in the compressor can also cause this issue, though this situation is more troublesome and usually requires replacing the compressor.

115

Share

What are the three must-have insurances for a car?

The must-have insurances for a car include: compulsory traffic insurance, third-party liability insurance, vehicle damage insurance, and passenger liability insurance. These are essential coverages. Compulsory traffic insurance is a mandatory insurance in China, and all vehicles must purchase this coverage. In the event of a traffic accident, the insurance company can only compensate the party that was hit, meaning the conditions for compensation are quite limited. Additionally, without compulsory traffic insurance, the vehicle will lose its eligibility for annual inspection. Therefore, compulsory traffic insurance is a must. Vehicle damage insurance is the most comprehensive necessary coverage. Whether the car suffers from collisions, scratches, water damage, or other harm, the insurance company will provide compensation. However, the final compensation amount depends on various factors such as the cause of the incident and the extent of the damage. Passenger liability insurance, also known as seat insurance, refers to the passenger portion of the vehicle's liability insurance. It covers situations where a qualified driver permitted by the policyholder causes an accident while using the insured vehicle, resulting in bodily injury or death to passengers inside the vehicle. The insurance company will compensate according to the insurance contract for the legal liability the policyholder must bear. Passenger liability insurance is a major component of commercial vehicle insurance, primarily functioning to compensate for injuries or deaths of passengers caused by traffic accidents.

107

Share

Is a distance less than 30 cm on a slope considered passing?

A distance less than 30 cm on a slope, without crossing the line, is considered passing. The requirement for stopping on an uphill slope with less than 30 cm means the right wheel should be less than 30 cm away from the right edge line. If the vehicle stops with the body 30 cm to 50 cm away from the road edge line, 10 points are deducted; if the body is more than 50 cm away from the road edge line, it is considered a failure. Uphill slope fixed-point stopping and slope starting are assessment points in the driver's test, consisting of two test items: first, fixed-point stopping on an uphill slope, and then starting the vehicle on the slope. This is one of the five mandatory test items. Mastering uphill slope fixed-point stopping and slope starting enables motor vehicle drivers to skillfully control the vehicle when stopping and starting on slope sections, preventing the engine from stalling or the vehicle from rolling backward and causing a rear-end collision during slope starts. For fixed-point stopping, the vehicle's front bumper must be in the middle of the yellow line for fixed-point stopping, with the bumper not exceeding or falling short of the yellow line by more than 50 cm. The front and rear right wheels must stop between the edge yellow line and the white line (width 30 cm). For slope starting, the vehicle must not roll back more than 30 cm.

110

Share

What are the reasons why the Baojun 560 cannot start?

The reasons why the Baojun 560 cannot start include insufficient battery power, steering wheel lock, and incorrect gear position. Detailed explanations and solutions are as follows: Insufficient battery power: Turn the ignition key to the ON position and turn on the headlights. If the lights noticeably dim or do not light up at all, and the horn sounds significantly weaker than usual or does not sound, it can be determined that the battery power is insufficient. Solution: Depending on your situation, you can seek assistance from nearby car owners for emergency measures such as jump-starting or towing. Steering wheel lock: If the steering wheel is locked and cannot start, this is a common anti-theft feature in many cars. After removing the key, if the steering wheel is not straightened or has been turned, the self-locking function of the steering wheel will activate, causing the steering lock pin and steering column to engage, making the steering wheel immobile and preventing the car from starting. Solution: Try turning the key while gently shaking the steering wheel. After a few attempts, the car should start. Incorrect gear position: Generally, the P (Park) or N (Neutral) gear is the correct position for starting an automatic transmission car. If the owner inadvertently leaves the gear in R (Reverse) or another position, the result will not only be the inability to start but also a potential safety hazard. Solution: Return the gear to the P or N position.

105

Share