···
Log in / Register

who is the person on singapore dollar note

1Answers
VonBriella
12/01/2025, 02:22:36 AM

Based on the provided information, the person featured on the Singapore dollar note is Yusof bin Ishak.

Yusof Ishak was a prominent Singaporean statesman who served as the first President of Singapore, holding the office from the country's independence in 1965 until his death in 1970. His portrait is featured on the front of all denominations of the current Portrait Series of Singapore currency notes, which was first issued in 1999. This series was launched to honor his foundational contributions to the nation.

While one of the provided sources from the Monetary Authority of Singapore (MAS) was unavailable due to a maintenance issue, the Wikipedia source correctly identifies Yusof Ishak as the person on the notes.

Was this review help?
105
Share
More Q&A

How do I configure the DYNALINK A 3245 HDMI Extender With USB KVM to control my device remotely?

Setting up the DYNALINK A 3245 HDMI Extender With USB KVM for remote device control is straightforward. Follow these steps to get your system up and running: First, plug your HDMI source device into the transmitter unit's HDMI IN port using an HDMI cable. Then, connect your display device to the transmitter's HDMI OUT port, also using an HDMI cable. Next, establish a connection between the transmitter and receiver units using a single Cat6/6a cable. After that, connect your keyboard and mouse to the USB ports available on both the transmitter and receiver. Once all connections are made, plug in the power adapters for both the transmitter and receiver units. Now, power on your devices in the following order: HDMI source device, transmitter, receiver, and finally, the HDMI display device. If you plan to use audio, connect a 3.5mm analog audio cable between the transmitter and receiver. With these steps completed, you should be able to remotely control your source device using your keyboard and mouse connected to the USB ports of the DYNALINK A 3245 HDMI Extender With USB KVM.
108
Share

How can I wall-mount my Princess Smart Infrared Panel Heater?

Mounting your Princess Smart Infrared Panel Heater on the wall is straightforward. Here's how: First, ensure the heater is positioned safely, maintaining at least 15 cm from the floor and 50 cm from the ceiling. The heater requires mounting at four points. Make sure there is a 300mm clearance on all sides of the heater for optimal performance and safety. Accurately measure the distance between the center of each bracket, both horizontally and vertically, to ensure precise hole placement. Use the provided wall mount drawings to mark the four drilling hole positions on the wall. Drill the holes and insert the plastic expanded plugs. Secure the heater by attaching it to the wall with the four supplied screws into the plugs. Finally, attach the panel heater onto the screws and slide it to the left until the screws are secured in the slots. Following these steps will allow you to safely and effectively install your Princess Smart Infrared Panel Heater.
106
Share

How to Install a SIEMENS 6EP1437-2BA20 Power Supply

Properly installing your SIEMENS 6EP1437-2BA20 power supply is crucial for optimal performance. Follow these steps for a secure and correct setup: First, mount the power supply on a standard TH35-15 (EN 60715) mounting rail. Second, when mounting, make sure the terminals are facing downwards. Finally, maintain adequate spacing around the device; ensure at least 40 mm of clearance above and below the unit, and do not exceed a 50 mm cable duct depth. Adhering to these guidelines will help ensure the reliable operation of your SIEMENS power supply.
105
Share

How do I install a REELCRAFT CT Series Air or Water Hose Reel?

To correctly install your REELCRAFT CT Series Air or Water Hose Reel, follow these steps for a safe and secure setup: Handle and Link Lever: Attach the handle assembly to the link lever on the reel. Swivel Valve Threading: Apply teflon tape or pipe compound to the swivel valve threads before threading it into the reel. Mounting the Reel: Use appropriate bolts (3/8” or 10mm) to firmly secure the hose reel to a ceiling, wall, or floor, ideally near your air compressor. Connecting the Supply Hose: Apply teflon tape or thread sealant to the built-in supply hose fitting on the reel. Connect this to the outlet of your air compressor. Attaching the Hose Fitting: Apply teflon tape or thread sealant to the threads of the hose fitting. Attach the hose fitting to the reel swivel valve and feed the hose through the flange opening. Tightening the Hose Fitting: Use a wrench to stabilize the swivel valve and tighten the hose fitting, preventing any potential damage to the swivel valve. Following these steps will help ensure your REELCRAFT CT Series Air or Water Hose Reel is properly installed for optimal performance and longevity. If you need further assistance, consult the REELCRAFT instruction manual or contact their customer service.
116
Share

How can I tell when my device is fully charged using the ACEFAST PD65W Fast Charge Wall Charger?

To know when your device is fully charged with the ACEFAST PD65W Fast Charge Wall Charger, keep an eye on your device's battery indicator. Your device's display will show a full battery symbol or a 100% charge status when it's completely charged. The ACEFAST PD65W charger itself doesn't have an indicator. After your device is fully charged, it is advisable to unplug it to avoid consuming unnecessary power. Regularly checking your device's charge status helps maintain its battery health.
106
Share

What is the correct way to install Siemens FB-300 backboxes and doors for Firefighters' Telephone Stations?

Installing the Siemens FB-300 backboxes and FC-300 door for Firefighters' Telephone Stations requires careful attention to detail and adherence to local regulations. Here's a straightforward guide: Mounting Preparation: Before you begin, consider the mounting height. Ensure the station is easily accessible for firefighters. Also, factor in the weight and dimensions of the FB-300 enclosure. Always check and comply with all local mounting codes and regulations. Backbox Installation: FB-300 Flush Mount: First, remove the necessary knockouts to accommodate field wiring. Then, position the empty backbox against the wall, making sure the "TOP" marking is facing upwards. Next, cut an appropriately sized hole in the wall, referring to the dimensions provided in the Siemens documentation. Mark the locations for mounting screws, drill pilot holes, and securely fasten the backbox to the wall using screws appropriate for the wall material. FB-301 Surface Mount: The surface mount installation follows a similar process as the flush mount, with adjustments made for mounting on the wall's surface instead of recessed within it. FC-300 Door Installation: Once the backbox is securely mounted, attach the FC-300 door using the screws provided. For break glass installation or replacement, consult the FT-GLS Installation Instructions document for specific guidance. By carefully following these steps and referring to the official Siemens documentation, you can ensure proper installation, maintain accessibility, and comply with all relevant standards for your Firefighters' Telephone Stations.
109
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.