···
Log in / Register

what is the value of a 1972 silver dollar with no mint mark

1Answers
KiraLynn
12/01/2025, 02:18:36 AM

Based on the information provided, a 1972 dollar with no mint mark is an Eisenhower Dollar that was struck at the Philadelphia Mint. It is important to clarify that these specific coins, intended for general circulation, are not made of silver. They are composed of a copper-nickel clad alloy. The term "silver dollar" is a common name for the denomination, but in this case, it does not reflect the coin's metallic content.

The value of a 1972 copper-nickel Eisenhower dollar is highly dependent on its physical condition. A coin that has been used in circulation and shows signs of wear and tear is typically only worth its face value of one dollar. The vast majority of these coins fall into this category.

For a coin that is in uncirculated, or "mint state," condition, the value increases. A standard uncirculated 1972 Eisenhower dollar might be valued at approximately $5. However, for specimens in a very high state of preservation, such as those graded MS 65, the value can rise to $25 or more. There are also rarer die varieties for this year that can be worth significantly more, but these require expert examination to identify.

Was this review help?
114
Share
More Q&A

What is the maximum number of devices supported by a single Siemens HLIM Loop Isolator Module?

For optimal performance and safety, the Siemens HLIM Loop Isolator Module Instruction Manual recommends connecting no more than 20 devices to a single module. This limit helps ensure the loop isolator functions correctly and protects the system. Always adhere to national and local wiring codes to maintain safety standards and system reliability when installing or connecting devices to the HLIM module. Exceeding the recommended device count may impact the module's performance.
116
Share

How do I install and mount my REELCRAFT WC7000 Series Welding Cable Reel?

Installing your REELCRAFT WC7000 Series Welding Cable Reel involves a few straightforward steps. First, inspect the reel for any shipping damage and ensure smooth operation by manually turning it. You'll then configure the reel for your preferred cable dispensing direction (top, side, or bottom) by adjusting the guide arm bracket. Next, position the reel on your chosen surface – floor, wall, or ceiling – and secure it using four bolts (customer-supplied). To install the output cable, remove the outer nuts from the collector ring cover and strip 1 1/8” of insulation from the cable. Route the cable around the reel spool, avoiding the guide arm opening, and add protective tubing to the spool opening. Route the input cable through the spool, collector ring base casting, and strain relief, securing it between the clamp plates with the nuts/screws. Tighten the strain relief and replace the collector ring cover. Fasten the cable to the spool using a u-bolt and nuts. Before winding the cable, check for ground faults using an ohmmeter. Wind the cable onto the spool, adding a few extra turns to create tension. Finally, add a bumper to the cable at your desired location. Always consult the REELCRAFT WC7000 Series Welding Cable Reel instruction manual for detailed diagrams and safety information.
106
Share

How do I correctly connect batteries to my SIEMENS PSC-12C 12 Amp Power Supply?

Connecting batteries to the SIEMENS PSC-12C 12 Amp Power Supply ensures backup power. Here's how to do it safely and correctly: Battery Compatibility: The PSC-12C is designed to charge batteries up to 100 amp hours and supports a minimum size of 12 amp hours. Recommended battery models include: Battery 12V/12AH (V24069-Z103-A12) Battery 12V/25AH (GBI:13013) Battery 12V/40AH (V24069-Z103-A6) Battery 12V/65AH (V24069-Z103-A7) Battery Connection Procedure: Use a 0.5-meter wire assembly to connect the batteries together. Secure each end of the wire assembly to the battery terminals using M5 screws and lock nuts. Attach the red wire to the positive (+) terminal and the black wire to the negative (-) terminal of the battery. Ensure the battery covers are securely closed. Circuit Breaker: Before connecting the batteries, make sure the battery circuit breaker on the SIEMENS PSC-12C is in the OFF position. Wiring: Use either 14 or 12 AWG (2.5mm2 or 4mm2) wire for the battery connection. Connect the earth ground from an appropriate source to the PSC-12C. Always adhere to local electrical codes and regulations during the wiring process. Following these steps helps guarantee a reliable backup power solution for your SIEMENS PSC-12C.
105
Share

How do I safely install the BePureHome 800391-B INTENSE Wall Cabinet?

To ensure your BePureHome 800391-B INTENSE Wall Cabinet is securely mounted, follow these steps: Wall Preparation: Before you begin, confirm your wall is suitable for installation. It should be flat, clean, and capable of supporting the cabinet's weight, along with its contents. Gather Materials: You'll need 4 wall plugs and 4 screws, which are not included with the cabinet. Purchase these from your local hardware store. Mounting the Cabinet: Position the cabinet on the wall at your desired height, ensuring it is level. Mark the wall where the screws will go. Drill holes at the marked spots, insert the wall plugs, and hold the cabinet against the wall. Drive the screws through the cabinet's mounting holes and into the wall plugs to secure it. Tilting Protection: Review the manual for specific instructions regarding tilting protection to prevent the cabinet from tipping over. Additional Tip: Consider adding felt glides under the cabinet's legs to protect hard floors and ease movement.
110
Share

How can I connect my Siemens RDM-PC Remote Diagnostics Module to my computer?

Connecting your Siemens RDM-PC Remote Diagnostics Module to your personal computer allows for remote diagnostics and monitoring of your MXL system. Here's how to do it: First, use the provided RS-232 DB9 cable to connect your PC or laptop to Port 232-A on the RDM-PC. Note that this is a straight-through RS-232 cable. The pin connections are as follows: RDM-PC (Port A, 9 pins, DCE) to PC/Laptop's COM port (9 or 25 pins). Second, connect the 24 VDC power pack to its connector located near Port C on the RDM-PC. Third, connect a standard telephone line to the RJ11 phone socket on the RDM-PC using an FCC Part 68 compliant telephone cord (usually supplied with the device). For a visual guide, please consult the connection diagram in the RDM-PC instruction manual (Figure 1), which illustrates the wiring setup.
108
Share

How do I install the TORO 08146 2-inch Receiver Draw Bar?

To install the TORO 08146 2-inch Receiver Draw Bar, follow these steps: Machine Preparation: Park your machine on a level surface. Engage the parking brake or put the transmission in the P (PARK) position. Turn off the machine and remove the key for safety. Attaching the Hitch Ball Mount: Insert the hitch ball mount into the receiver at the back of your machine. Put the hitch pin through the holes in both the receiver and the hitch ball mount. Secure everything with the hairpin cotter. Key parts to know: Hairpin cotter Receiver Hitch ball mount Hitch pin Towing Your Trailer: For important towing details, please consult your machine's Operator's Manual. By following these instructions, you'll ensure your TORO 08146 2-inch Receiver Draw Bar is correctly installed for safe and effective towing. If any part of the installation feels unclear, check the manual, or reach out to TORO customer support for help.
117
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.