Browse
Marketplace
Collectibles & ArtClothing & ShoesBaby & KidsBooks · Movies & MusicElectronicsHealth & BeautyHome & GardenPet SuppliesSports & OutdoorsTicketsToys · Games & HobbiesAuto Parts & AccessoriesBusiness & IndustrialOther
Jobs
AccountingAdministration & Office SupportAdvertising · Arts & MediaBanking & Financial ServicesCall Center & Customer ServiceCEO & General ManagementCommunity Services & DevelopmentConstructionConsulting & StrategyDesign & ArchitectureEducation & TrainingEngineeringFarming · Animals & ConservationGovernment & DefenseHealthcare & MedicalHospitality & TourismHuman Resources & RecruitmentInformation & Communication TechnologyInsuranceLegalManufacturing · Transport & LogisticsMarketing & CommunicationsMining · Resources & EnergyReal Estate & PropertyRetail & Consumer ProductsSalesScience & TechnologySelf EmploymentSport & RecreationTrades & ServicesOther
Property
For RentFor Sale
Cars
Used CarsOthers
Services
Home Cleaning & ChildcareEntertainmentFinancial & LegalHealth & BeautyTradesmen & ConstructionRepair ServicesMoving ServicesTutors & ClassesIT & ProgrammingPetsOther
Community
Activities & GroupsArtists & MusiciansClasses & LessonsEventsFriendship & NetworkingLost & FoundRideshareSports TeamsVolunteersTravel & Travel PartnersSkills & Language SwapOther
···
Log in / Register

How do I get the DC2369A demo circuit up and running?

1Answers
CarterMarie
12/17/2025, 11:34:06 AM

Powering the DC2369A demo circuit is straightforward. Begin by ensuring that slide switch SW1 is in the ON position. The circuit operates using the two AAA batteries included with your demo circuit. This switch activates the enable pin of the LTC3335 power supply. To confirm the power supplies are functioning correctly, measure the voltage on the back of the circuit board. The voltage between VDD and GND should be 3.3V, and the voltage between VREF and GND should be 3.0V. For more detailed instructions on the DC2369A demo circuit's operation, please consult the DC2369A instruction manual.

Was this review help?
118
Share
More Q&A

How do I best clean and care for my FRANKE EOS NEO Stainless Copper Kitchen Faucet?

Keeping your FRANKE EOS NEO Stainless Copper Kitchen Faucet looking its best and functioning flawlessly is straightforward with the right care. Here's a guide based on the installation manual: Regular Inspections: Periodically check the connection and shower hoses for any signs of leaks, corrosion, or mechanical damage. Replace any hoses that show these issues immediately, using only genuine FRANKE spare parts. Pre-Installation Flush: Before installing your faucet, ensure all pipes are thoroughly flushed. This removes debris and impurities that could negatively impact your faucet's performance. Operating Guidelines: Adhere to the recommended operating pressure and water temperature outlined in the manual. The ideal operating pressure is 3 bar (45 PSI), with a maximum of 5 bar (70 PSI) and a minimum of 1 bar (14.5 PSI). The recommended water temperature is 60°C (140°F), with a maximum of 70°C (158°F). Balanced Pressure: Maintain equal pressure throughout your water system to ensure your FRANKE EOS NEO faucet operates as intended. Cleaning Routine: For cleaning, use a mild soap solution and a soft cloth to wipe down the faucet's surface. Avoid abrasive cleaners or pads that could scratch the finish. Rinse thoroughly with water and dry with a clean cloth to prevent water spots. Maintenance Checks: Regularly check for any leaks, drips, or unusual noises while using the faucet. Address any issues promptly to prevent potential damage. By following these simple steps, you can keep your FRANKE EOS NEO Stainless Copper Kitchen Faucet in excellent condition and enjoy its premium performance for years.
101
Share

How do I control the browning of waffles with the FriFri WA102 Multex Belgian Waffle Maker?

To adjust the browning level of your waffles with the FriFri WA102 Multex Belgian Waffle Maker, utilize the integrated thermostat. Here's how: Locate the thermostat adjustment button; it's positioned centrally on the top cover of the waffle maker. This button features a dial with eight settings. For optimal results with most batter types, aim for a setting between 6 and 8. To achieve your preferred level of browning, rotate the dial clockwise. The signal light will extinguish once the FriFri WA102 has reached the set temperature, typically within a few minutes. At this point, the waffle maker is ready for use, and your waffles will cook to the desired crispness or softness. Experiment with the settings to discover your ideal waffle perfection!
101
Share

How do I best clean and maintain my Polaris PCWH 0512D ceramic heater?

Keeping your Polaris PCWH 0512D ceramic heater in top condition ensures it runs efficiently and lasts a long time. Here's a guide to cleaning and maintenance, mirroring the manufacturer's recommendations: Cleaning Your Heater: Safety First: Always unplug the heater and let it cool completely before cleaning. Surface Cleaning: Use a soft, damp cloth to wipe down the exterior. Avoid harsh chemicals, solvents, or abrasive cleaners, as these can damage the heater's finish. Regular Dusting: Dust the ceramic heater regularly. Dust buildup can reduce the heater's performance. Avoid Damage: Never use sharp or hard objects to clean the heater, as these could scratch or damage internal components. Cleaning Frequency: Optimal Performance: Clean your heater regularly to maintain its efficiency. The frequency will depend on your environment, but aim to clean it whenever dust accumulates. Maintenance Tips for Your Heater: Power Off: Always unplug the heater before any cleaning or maintenance. Ventilation: Ensure the heater's hot air outlet remains unobstructed. Safe Operation: Do not allow children to operate the heater or insert objects into it. Cord Care: Protect the power cord from damage; do not twist, pull, or place heavy objects on it. Inspection: If you suspect any damage to the power cord or the heater itself, stop using it immediately and contact the service department for inspection and repair. Storage: Store the heater in a clean, dry room at a moderate temperature when not in use. Transportation: When moving the heater, follow the transportation guidelines in the manual to prevent damage. By following these cleaning and maintenance steps, you can help keep your Polaris PCWH 0512D ceramic heater working optimally.
109
Share

How do I connect the remote to my RC Spider-Man 2017 Ford GT?

To link your remote control with your RC Spider-Man 2017 Ford GT, follow these steps. First, power ON the vehicle. Then, within 30 seconds, turn ON the transmitter controller. Next, press the trigger on the controller back and forth once to initiate the connection process. Avoid pressing any other buttons or switches during pairing to prevent interference. The LEDs on both the vehicle and the controller will begin to blink. A successful pairing is indicated when the LEDs on both the vehicle and controller stop blinking and remain lit. If pairing fails, turn both the vehicle and controller OFF and try again. If your controller's LED blinks or dims, replace the batteries. If your vehicle's LED blinks or dims, recharge the vehicle's battery. When operating multiple RC vehicles, ensure you pair each controller to its respective vehicle one at a time to prevent signal interference. Following these steps will help ensure successful remote pairing for optimal enjoyment of your RC Spider-Man 2017 Ford GT.
119
Share

How to install the Lithonia Lighting BGR ALO SWW2 MVOLT PER Dusk to Dawn LED Area Light?

Installing the Lithonia Lighting BGR ALO SWW2 MVOLT PER Dusk to Dawn LED Area Light involves several steps. Before beginning, gather these tools: a drill, lag bolts, wire nuts, conduit, silicone sealant, and an Allen wrench (if using a mounting arm). Prioritize safety by switching off power at the circuit breaker. Do not rely solely on the wall switch. Begin with the photocontrol installation; align the arrow on the photocontrol with the receptacle arrow and twist clockwise to lock. Keep the photocontrol or Shorting Cap installed. For surface mounting, remove the conduit plug and feed supply wires through the hole. Use the provided template to mark mounting hole locations and drill pilot holes. Secure the fixture with lag bolts. If using an optional Mounting Arm (OMA), follow its instructions for attachment. Connect wires, insert the mounting arm into the fixture arm hole, and secure with set screws. Ground the fixture by connecting the house supply ground wire to the fixture ground wire using a wire nut. Connect the black and white fixture wires to the corresponding power supply wires with wire nuts. Turn on the electricity to test the fixture. Adjust the brightness and light color using the fixture's settings. For the diffuser, align its keyholes with the fixture bottom heads, push up, and rotate to install. Tighten screws to secure. This LED light requires minimal maintenance; clean surfaces with mild soap and water, avoiding abrasive materials. If issues arise, check power, wiring, line voltage, and the Photocontrol. Consult the manual for troubleshooting or contact Technical Support for further assistance. Following these steps ensures successful installation and operation of your Lithonia Lighting BGR ALO SWW2 MVOLT PER Dusk to Dawn LED Area Light.
120
Share

How do I set the mowing schedule on my Einhell 1200 LCD BT Robot Lawn Mower?

Scheduling your Einhell 1200 LCD BT Robot Lawn Mower ensures your lawn stays perfectly manicured with minimal effort. Here's how to program the mowing schedule: First, access the settings menu by pressing the "SET" button. Then, follow these steps: To set the time and date navigate to "Time/Date" using the arrow keys and press "OK". Set the current time and date, confirming each with "OK". Next, to set the mowing schedule, go to "Mowing Schedule" and press "OK". Choose the days for mowing using the arrow keys and confirm with "OK". Set the start time and the mowing duration, confirming each with "OK". Finally, check the settings menu to ensure the schedule is activated. The mower will then automatically mow according to your schedule. Always consult your Einhell 1200 LCD BT Robot Lawn Mower's instruction manual for specific details.
114
Share
Trending Ranking
What are the proper installation steps for the PULS UB40.241 DIN Rail Controller?
How do I replace the drill bit on my BOSCH GBH 18V-36 C Professional Rotary Hammer?
How to configure RS485 communication on the NOVUS N321S Differential Temperature Controller?
4
How can I clean the air filters on my Seasons SP07H2-20 heat pump?
5
How do I assemble the ASHLEY A8010297 Floxville Floorstanding Mirror safely and correctly?
6
What's the best way to clean my Fisher & Paykel PG4V*0 or PB*4V*0 ceramic hob?
7
How to configure RS485 communication for the NOVUS N321S Differential Temperature Controller?
8
What are the proper torque specifications for tightening nuts on a Smith-Blair TI-008 Full Circle Repair Clamp?
9
How to Install the GLOBO LIGHTING 12379-6W Simple Ceiling Lamp?
10
How do I find digital instructions for the LEGO 71416 Super Mario Lava Wave Ride Expansion Set?
More Q&A

How do I securely anchor a storage chest to a wall to prevent it from tipping?

119
1

How can I best maintain and care for my FRANKE FC 0044.501 EOS NEO Stainless Steel Kitchen Faucet?

116
1

What is the best way to maintain my FRANKE FC 0044.505 EOS NEO Copper Kitchen Faucet?

104
1

How do I assemble the MULTIPLEX 1-01771 RaceWulf RR Racer model airplane?

104
1
About Us
Terms of Use
Privacy Policy
Help
Contact Us
FAQ
Cookie
Cookie Policy
Cookie Settings
© 2025 Servanan International Pte. Ltd.