Where is the cabin air filter located in the Peugeot 2008?

What is the reason for the ABS and anti-skid lights on the Leiling being on?

The reasons for the ABS and anti-skid lights on the Leiling being on: It may be due to a faulty sensor; use a computer to check the ABS sensor and eliminate the fault. A constantly lit ABS light indicates an anti-lock braking system alarm. Normally, the light turns on when the ignition is switched on or the engine is started, and the system enters an automatic detection program. After the detection is completed, the light turns off. If the light does not turn on after switching on the ignition, or if it does not turn off after lighting up, or if it lights up while driving, it indicates a system fault. Solutions for the ABS light being on: 1. Carefully inspect the wiring and connectors to see if there is poor contact or damage; 2. Check the installation gap and position of the wheel speed sensor and the toothed ring, as well as any contamination by dust or impurities; 3. Check if the wheel bearing gap is too large and adjust it to the normal value; 4. Avoid high-speed driving and sudden braking, and take the car to a 4S shop for repair as soon as possible. The Leiling's body dimensions are 4640mm in length, 1780mm in width, and 1455mm in height, with a wheelbase of 2700mm.

19

5

Share

What are the test items for B2 Subject 2?

Hill start and stop, parallel parking, single-plank bridge crossing, curve driving, right-angle turning, passing through width-limited gate, stake test, narrow road U-turn, simulated highway driving, simulated emergency handling, continuous sharp turns on mountain roads, simulated emergency handling, simulated tunnel driving, and driving in rainy and foggy weather. These are the 14 test items for B2 driver's license Subject 2. The details of the B2 Subject 2 test items are as follows: Stake test: Reverse into the B garage from the starting point and stop correctly, then move the vehicle into the A garage with two advances and two reverses and stop correctly, then move forward out of the B garage to the control line, reverse into the A garage and stop correctly, and finally return to the starting point. The vehicle must not stop during the process, and the total time must not exceed 8 minutes. Parallel parking: After parking the vehicle on the right side in front of the garage, reverse into the garage in one go without stopping, and the wheels must not touch the lane boundary or garage boundary. Single-plank bridge crossing: During the test, the vehicle must not stop, and the wheels must not fall off the bridge. Narrow road U-turn: Drive the vehicle to the U-turn section and park on the right, complete the U-turn with no more than three advances and two reverses. The test time must not exceed 5 minutes. Right-angle turning: Drive the vehicle along the designated route, make a right-angle turn from left to right or right to left in one go without stopping, and the wheels must not touch the lane boundary. Curve driving: Commonly known as S-curve. The test requires the vehicle to drive on an S-shaped road of a specified width without pressing the edge of the road, and the steering must be used smoothly. This tests the driver's ability to control the vehicle through curves. The purpose is to train the driver's steering skills and mastery of wheel trajectory. Hill start and stop: Control the vehicle to stop accurately and start smoothly without rolling back. The starting time must not exceed 30 seconds. Simulated highway driving: After driving to the entrance ramp, turn on the left turn signal, look back to the left to observe the traffic, confirm safety, accelerate into the lane to the minimum speed limit, and drive normally, then turn off the turn signal. When changing lanes, turn on the turn signal of the lane you are about to enter, observe the traffic, and change lanes after confirming safety. When exiting the highway, adjust the speed and lane in advance according to the exit signs. Simulated emergency handling: During normal driving, randomly select one of the following emergency situations and simulate it with voice or lights: If an obstacle suddenly appears ahead, brake immediately, stop quickly, and turn on the hazard warning lights after stopping. In case of a tire blowout or other vehicle failure on the highway, slow down reasonably, observe the following traffic, park the vehicle steadily in the emergency lane, turn on the hazard warning lights, prompt passengers to move outside the guardrail, place the warning sign correctly, and the driver should move outside the guardrail and simulate calling for help. Simulated tunnel driving: Observe the road signs before driving into the tunnel and operate according to the signs. Slow down when approaching the tunnel, turn on the headlights, honk the horn, honk the horn again when approaching the tunnel exit, and turn off the headlights. Do not honk the horn in no-honking zones. Simulated driving in rainy (foggy) weather: Slow down the vehicle. In rainy weather, select the wiper speed according to the rain intensity. In foggy weather, turn on the fog lights, position lights, headlights, and hazard warning lights. Simulated driving on slippery roads: Slow down before entering the slippery road, then use low gear to drive at a constant speed and control the vehicle direction smoothly. Simulated driving on continuous sharp turns on mountain roads: Slow down before entering the curve, drive on the right side, honk the horn before entering the curve, and do not occupy the opposite lane during driving. Passing through width-limited gate: Drive through the three gates at a speed of no less than 10 km/h without touching the hanging rods.

14

0

Share

What is the replacement interval for the Kia K5 air filter?

According to the maintenance manual of the Hyundai Kia K5, the air filter should generally be replaced every 10,000 to 20,000 kilometers or every other maintenance interval. However, it is recommended to clean the air filter every 5,000 kilometers to reduce the buildup of throttle sludge. The location of the car's air filter varies depending on the intake form and the engine structure. It is usually located in the air cleaner on the engine intake pipe. There are two types of air filters in cars: dry and wet. Dry filters are made of paper or organic materials, while wet filters are made of metal wire mesh. Function of the air filter: It filters out particulate impurities in the air, ensuring that a sufficient amount of clean air enters the cylinder, preventing floating dust in the air from being sucked into the engine, which accelerates the wear of the piston group and the cylinder. Air filter: It is a type of filter, also known as an air filter cartridge, air cleaner, or style. It is mainly used in engineering vehicles, cars, agricultural vehicles, laboratories, sterile operating rooms, and various precision operating rooms as an air filter. During operation, the engine inhales a large amount of air. If the air is not filtered, the suspended dust in the air will be sucked into the cylinder, accelerating the wear of the piston group and the cylinder. Larger particles entering between the piston and the cylinder can cause severe cylinder scoring, which is particularly serious in dry and sandy working environments. The air cleaner is installed in front of the carburetor or intake pipe to filter out dust and sand particles in the air, ensuring that sufficient and clean air enters the cylinder. Dirty air cleaner: Using a dirty air cleaner while driving can cause insufficient engine intake, leading to incomplete fuel combustion, resulting in unstable engine operation, reduced power, and increased fuel consumption. Therefore, the car must keep the air cleaner clean. The car air cleaner is a device that removes particulate impurities from the air, consisting of one or several air filter components. Its main function is to filter out harmful impurities in the air that are about to enter the cylinder, reducing early wear of the cylinder, piston, piston rings, valves, and valve seats. Therefore, before air enters the cylinder, it must first pass through the fine filtration of the air cleaner. A dirty air cleaner can cause poor engine performance, excessive fuel consumption, and engine damage. When inspecting the air cleaner, if it is found to have little dust and is lightly clogged, it can be cleaned by blowing high-pressure air from the inside out and continue to be used. A severely dirty air cleaner should be replaced promptly.

8

4

Share

How Many Kilometers Can a Spare Tire Travel?

Spare tires are categorized into full-size spare tires and compact spare tires. For compact spare tires, the total mileage should not exceed 50 kilometers. Full-size spare tires are identical in size to regular tires and have no mileage restrictions, but they must be driven at lower speeds. Full-size spare tires have the exact same specifications as the other four tires on the vehicle and can replace any temporarily or permanently unusable tire. Compact spare tires have slightly smaller diameters and widths compared to the other four tires and are only intended for temporary use. They should only be used on non-driving wheels, and the maximum speed should not exceed 80 kilometers per hour.

15

4

Share

What does the AC switch in the car air conditioner mean?

In-car air conditioner AC switch refers to the cooling switch of the vehicle air conditioning system. When this button is pressed, the air conditioning compressor starts working, and the air blown out by the blower becomes cold. During summer when you need to lower the temperature inside the car, press this button and turn the temperature selection switch to the blue section to get cold air. If the car is equipped with automatic air conditioning, simply press this button and then press the AUTO button. The car air conditioning system is designed to adjust and control the temperature, humidity, air cleanliness, and air flow inside the vehicle cabin to an optimal state, providing a comfortable environment for passengers, reducing travel fatigue, creating good working conditions for the driver, and serving as an important ventilation device for ensuring safe driving.

3

4

Share

What Causes the Creaking Sound When Pressing the Accelerator Pedal?

The primary reason for a creaking sound when pressing the accelerator pedal is the aging of the throttle cable. Below are the related explanations: 1. Throttle Issue: The throttle cable may be aging or there could be mechanical wear between the accelerator pedal. Solution: Lubricate with engine oil. 2. Excessive Gap: The free play has increased. Solution: Adjust at a repair shop. 3. Clutch Problem: Consider the wear of the clutch. If pressing the accelerator makes it difficult for the vehicle to accelerate, this is a slipping phenomenon caused by thinning clutch plates. If there is noise, it is likely due to damage to the clutch release bearing. It could also be caused by excessive free play in the clutch. Solution: Timely repair or replacement of the clutch.

20

2

Share

Where is the cabin air filter located in the Peugeot 2008?

What is the reason for the ABS and anti-skid lights on the Leiling being on?

What are the test items for B2 Subject 2?

What is the replacement interval for the Kia K5 air filter?

How Many Kilometers Can a Spare Tire Travel?

What does the AC switch in the car air conditioner mean?

What Causes the Creaking Sound When Pressing the Accelerator Pedal?

What are the differences between Toyota Land Cruiser and Prado?

What to Do When the Wrangler Key is Locked in the Car?

How to test if ETC is working?

What do Volvo's T3, T4, and T5 mean?