What is the tire model of the Bestune T77?

What tires does the Tucson use?

The original tire specification for the Tucson is 225/55R18, which belongs to the premium series of Bridgestone tires. Below are some relevant materials about the tires: Tips to extend tire lifespan: 1. Pay attention to daily tire maintenance. Regularly check for punctures, scratches, or bulges caused by broken cords. 2. Monitor tire pressure periodically. Check tire pressure frequently and measure it every month, topping it up as needed. Always check tire pressure before highway driving to ensure it is within the normal range. 3. Develop good driving habits. 4. Try to avoid sudden starts, hard braking, and fast cornering, as these actions can accelerate tire wear and increase instantaneous pressure. Avoid running over hard objects on the road and control your speed.

109

Share

How to Remove the Santana 3000 Steering Wheel?

Santana 3000 steering wheel removal method: Unscrew the two screws of the steering wheel and remove the steering wheel cover. Next, pry open the gap of the steering wheel cover along the direction of the vehicle's headlight switch handle. Then remove the three clips of the steering wheel airbag. Finally, pull out the steering wheel with force. Below are some related details about the Santana: 1. The Santana 3000's headlight illumination system uses round projection lamps, with a horizontal strip-shaped position light at the lower part of the headlight that reflects incoming light from all directions. This projection lamp improves safety by enhancing nighttime illumination. 2. The Santana 3000's ABS is equipped with an electronic automatic distribution EBD system, which mainly offers three benefits: maintaining steering control ability during braking; ensuring directional stability of the vehicle during braking; and shortening the braking distance.

102

Share

How to Set Up the Leiling Trip Computer Display?

To set up the Leiling trip computer display, you can use the directional buttons on the circular control located on the right side of the steering wheel to select items within the instrument panel's trip computer. Below are specific solutions for when the car display screen does not light up: 1. Check whether the power supply to the display screen is normal. If the power supply is abnormal, replace the power supply module. 2. Check if the ribbon cable connection is secure. If the connection is loose, promptly inspect whether the wiring has poor contact, which could cause the central control screen to go black. Reconnect any loose parts properly. 3. Check if the display screen is damaged by replacing it for testing. If the issue is resolved, the display screen is damaged. If the power supply is normal and the ribbon cable connection is secure, inspect the video output signal of the motherboard and test by replacing the motherboard.

115

Share

How to Turn Off the Daytime Running Lights on the Lynk & Co 02?

The daytime running lights on the Lynk & Co 02 cannot be turned off as they automatically activate as a warning light. The only way to disable them is by removing the daytime running lights or installing an additional switch. Below are the usage instructions for the Lynk & Co 02 daytime running lights: 1. Rotate the wheel on the Lynk & Co 02 headlight combination switch to set the external lighting type. 2. When the automatic high beam is activated, the automatic high beam indicator on the driver's display lights up in white; when the automatic high beam is on, the indicator turns blue. After the automatic high beam is turned off, the headlight mode switches to low beam. 3. Pull the combination switch lever toward the steering wheel to flash the high and low beams; push the lever forward to enable continuous high beam lighting, which can only be activated when the light adjustment wheel is set to AUTO or headlight mode. When the high beam is on, the high beam indicator on the driver's display lights up in blue.

120

Share

When Should a Car Be Refueled?

Car should be refueled when the fuel gauge indicates one-quarter of the fuel remaining. Here is the relevant content introduction: 1. Generally, when the fuel light comes on, it means the fuel level has started to fall below the fuel pump, and the fuel in the tank is almost exhausted. When the fuel level is too low, the sediment remaining at the bottom of the tank will be drawn up for fuel supply, which can easily cause fuel line blockage or fuel pump obstruction. 2. Engine oil, motor oil, or engine lubricant is a substance enhanced with additives in base oil, mainly containing anti-wear additives, detergents, dispersants, and multi-grade oil viscosity index improvers. Engine oil is used for lubricating internal combustion engines. The main functions of engine oil are to reduce friction and wear of moving parts and to remove sludge (one of the functions of dispersants) and varnish (function of detergents) from the engine.

115

Share

Can Gear Oil Be Used as Engine Oil?

Gear oil cannot be used as engine oil. Below are the reasons why gear oil cannot be used as engine oil and the functions of gear oil: Reasons why gear oil cannot be used as engine oil: Gear oil is mainly used for lubricating heavy-duty transmission gears, featuring high viscosity and excellent pressure resistance and anti-wear properties. If engine oil is used as a substitute for gear oil, its low viscosity and poor pressure resistance and anti-wear performance can easily lead to gear damage. Additionally, engine oil tends to foam during gear rotation, further deteriorating lubrication. Therefore, gear oil must be selected according to requirements and cannot be substituted. Functions of automotive gear oil: Automotive gear oil is used in gear transmission components such as transmissions, steering gears, and differentials. It serves to lubricate, reducing wear on gears and other moving parts and extending gear life. It also reduces friction, minimizing power loss, and helps dissipate heat, providing some cooling effect while preventing corrosion and rust. Additionally, it lowers operational noise, reduces vibration and impact between gears, and cleans contaminants, especially those on gear surfaces, thereby reducing wear.

113

Share