What is the entire process of the Subject 3 driving test?

[SanErin]

Subject 3 driving test process: Preparation before starting: First, enter the vehicle and verify identity information. After confirmation by the safety officer, exit the vehicle to perform a walk-around inspection. Once safety is confirmed, re-enter the vehicle to adjust mirrors and seat position, while checking if the gear, handbrake, and lights are reset. Starting the vehicle: Activate the left turn signal and check the rear traffic by turning your head. After confirming safety, sound the horn and slowly enter the left lane. Note: Start in first gear, release the clutch slowly, and apply appropriate throttle to prevent stalling. The starting phase requires smooth operation—no rolling back, jerking, or stalling. Driving in a straight line: While driving straight may seem the simplest task, many fail here. Due to high usage of test vehicles and operation by novices, the vehicle may not drive straight even when the steering wheel is centered, indicating inaccurate alignment. In this situation, the student should focus on the distant view, making minor steering adjustments (excessive movement leads to failure) to maintain a straight path rather than keeping the wheel fixed.

[LeilaniLynn]

I almost failed the driving test for Subject 3, sweating nervously in my palms. The whole process started before getting in the car: after the examiner verified my identity, I sat in the driver's seat, adjusted the seat and mirrors, fastened the seatbelt, and started the engine. The next step was crucial—turning on the turn signal, checking the mirrors, and starting smoothly without stalling. During the test, I had to follow instructions, such as driving straight and accelerating to around 40 km/h while maintaining control of the steering wheel. Before reaching an intersection, I had to slow down and check the traffic on both sides to ensure safe passage. Lane changing and pulling over were the most challenging parts: when changing lanes, I had to turn my head to check the blind spot to confirm no cars were there before signaling and turning; pulling over required slowly moving to the right and stopping at the designated spot, 30 cm from the curb without crossing the line. Throughout the process, the examiner watched to ensure I drove safely, avoiding running red lights or getting distracted by my phone. After driving for over ten minutes, I had to turn off the engine, pull the handbrake, report completion, and receive the results. After the test, I felt exhausted but learned a lot of driving skills, such as how observation is the most important—unlike some people who panic and cause accidents when nervous.

[SanManuel]

After taking the driving test for so many years, the common steps are simple, but the key lies in execution. Before getting in the car, don't rush—check the vehicle condition, ensure the dashboard is normal, then adjust the seat and fasten the seatbelt before starting the car. When the examiner gives the instruction to start, signal with the turn indicator, check the rearview mirror, and accelerate smoothly without sudden bursts to merge into the main road. Throughout the drive, operations include maintaining a straight lane without unnecessary maneuvers, and adjusting speed according to instructions, such as accelerating to 50 km/h without exceeding the limit. At intersections, always slow down, observe left and right, and pass safely. When changing lanes, signal first, confirm no cars in the blind spot, then proceed. For pulling over, find the right spot, slowly move to the right, and stop close to the curb without scraping it. At the end, turn off the engine and report—steps are simple, but don’t forget details as examiners focus on safety. My advice is to practice these basics repeatedly to avoid mistakes like turning too sharply, a common error for beginners—pay extra attention and don’t be overconfident. The whole process takes 10 to 15 minutes—remember, safety first to ensure a smooth pass.

[Chavez]

I failed the driving test (Subject 3) and really regret not paying attention to details. The process involves checking ID, adjusting seat and mirrors, fastening seatbelt, starting the car, listening to examiner's instructions, and starting straight while maintaining proper speed control. Then comes lane changing - signal, check blind spot, turn slowly without rushing; slow down at intersections, check safety lines before proceeding, don't rush traffic signals. Parallel parking was the hardest part - I didn't position properly within 30cm when the examiner called stop, then needed to turn off engine and report. The entire test takes under 15 minutes, but minor mistakes like forgetting to check blind spots during lane changes will deduct points. The lesson learned is that neglecting details ruins everything.

[IsaacFitz]

The entire examination process emphasizes strict adherence to safe driving rules. Before getting in the car, prepare by adjusting the seat, mirrors, fastening the seatbelt, checking the dashboard, and starting the engine. The examiner gives instructions during driving: start smoothly, use turn signals, check mirrors to ensure safety; maintain speed and lane position when driving straight; slow down at intersections, observe the surroundings, and pass cautiously; when changing lanes, check blind spots, signal, then turn; for roadside parking, choose a spot, slow down, and park close to the curb without crossing the line. Conclude by turning off the engine, engaging the handbrake, and reporting to the examiner that the test is complete. The core is to follow traffic rules at every step, avoid common risks like distraction or speeding, and not let details become loopholes to ensure a safe pass.

[VanEverett]

The third subject is the on-road driving test, so remember the steps clearly. Before getting in the car, the examiner verifies your identity. Once seated, adjust the seat and mirrors, fasten the seatbelt, start the engine, and wait for instructions before moving off. Use the turn signal and accelerate smoothly—don’t rush. During the drive, maintain a straight path, control your speed (not too fast), and steer steadily without wobbling. Slow down at intersections, check for traffic, and proceed safely—don’t forget to use your lights. When changing lanes, signal first, check your blind spot by looking over your shoulder, then maneuver smoothly into the lane. Finally, pull over gradually to the right, stopping within 30 cm of the curb, turn off the engine, engage the handbrake, and report the end of the test. The whole process takes about 15 minutes and tests real driving skills—don’t overlook these small steps. Practice a few times, and it’ll become second nature—just stay calm and natural.