···
Log in / Register

What are the dimensions of the Santana's trunk?

1Answers
TheoLee
07/24/2025, 07:53:29 PM

The maximum width of the Volkswagen Santana's trunk is 1000mm, the maximum depth is 590mm, and the height is 590mm. According to these dimensions, the luggage compartment volume is 466L. Here are the detailed specifications of the Santana: 1. Powertrain: The Santana 1.5L is equipped with an EA211 series 1.5L naturally aspirated engine, with a maximum power of 110 horsepower and a maximum torque of 150 Nm. The transmission system is matched with a 5-speed manual or 6-speed automatic transmission, and comes standard with auto start-stop and brake energy recovery. 2. Features: It is equipped with safety features such as ESP electronic stability program, static cornering assist lighting system, comprehensive six airbags, and front seat pyrotechnic pre-tensioning force-limiting seat belts. Additionally, it offers comfort features including an air conditioning system with dust filter, cruise control, dual-opening anti-pinch electric sunroof, and a multifunction steering wheel.

Was this review help?
120
Share
More Q&A

Where is the first aid kit in an Audi car?

Audi's first aid kit is located inside the side trim panels in the trunk. You can see it by opening the trunk's interior trim panels. The first aid kit contains emergency supplies such as gauze, medical cotton swabs, gloves, tape, bandages, as well as some vehicle tools (warning triangle and tire removal tools) which are also placed in the trunk. Not all Audi models are equipped with a first aid kit; only some high-end models have it. Taking the Audi A6 as an example: it is a luxury car produced by Audi, available in both sedan and station wagon versions. It incorporates Audi's high-tech proprietary technologies, further enriches the luxurious configurations, and is endowed with strong sports characteristics. Its features are luxury, dynamism, and sophistication.
112
Share

What is the focusing adjustment method for xenon headlights?

Xenon headlights are adjusted for focus by: removing the screws of the xenon headlight assembly, then removing the bulb clip, turning on the light and moving the bulb upwards, observing the focal point against a wall—the focal point should be slightly above the cut-off line. The light emitted by xenon headlights is concentrated and directed forward, evenly spreading across the road surface to ensure sufficient brightness for forward visibility. Xenon headlights, also known as high-intensity discharge (HID) lamps, are a type of heavy metal lamp. They work by filling an ultraviolet-resistant quartz glass tube with various chemical gases, including xenon and other inert gases, and then using a booster to instantly increase the vehicle's 12-volt power supply to 23,000 volts. Under this high voltage, xenon gas is ionized, creating a light source between the two electrodes.
108
Share

What Causes Car Vibration at Speeds Above 130 km/h?

At that speed range, the engine's vibration frequency becomes close to the natural frequencies of the drivetrain and vehicle body, triggering resonance. Potential causes include: worn/loose component connections, unbalanced driveshaft, incorrect wheel alignment, uneven tire pressure, or bent axle shafts. Detailed explanations: 1. Severe carbon buildup: Can clog spark plugs and valves, directly causing idle vibration. If acceleration deteriorates significantly with persistent shaking, consider engine decarbonization. 2. Unstable fuel mixture: First replace the fuel filter, as prolonged use may cause clogging. 3. Misfiring cylinders: Faulty ignition coils or spark plugs failing to ignite properly will cause noticeable vibration.
102
Share

How Often Should Mercedes-Benz Brake Pads Be Replaced?

Mercedes-Benz brake pads are not replaced based on mileage. Generally, they need to be replaced when the brake warning light comes on. Additionally, you should check the thickness of the brake pads; if it is below 3mm, replacement is usually necessary. Here are the methods for inspecting brake pads: 1. Check the thickness: A new brake pad is typically about 1.5cm thick. As it wears down through friction, the thickness gradually decreases. When the visible thickness of the brake pad is reduced to about 1/3 of its original thickness (approximately 0.5cm), the owner should increase the frequency of self-inspection and be prepared to replace it. Some models, due to wheel design, do not allow for visual inspection, and the tire must be removed to check. 2. Listen for sounds: If a metallic scraping or squealing noise is heard when lightly applying the brakes (this could also be due to initial break-in of newly installed brake pads), the brake pads must be replaced immediately. 3. Feel the pedal response: If you notice that the brake pedal feels harder to press and requires deeper application to achieve the usual braking effect, or if the pedal position feels noticeably lower during emergency braking, it may indicate that the brake pads have lost most of their friction and must be replaced.
113
Share

Where is the diagnostic connector located on the Peugeot 5008?

The diagnostic connector of the Peugeot 5008 is located inside the cabin. There is an OBD-labeled clip at the diagnostic connector; opening the clip reveals the diagnostic connector interface. The purpose of the car's diagnostic connector is: when the car malfunctions, the fault codes can be read through the car's OBD interface, and then the faults can be analyzed and cleared. Relevant information is as follows: 1. The OBD system continuously monitors whether the car's exhaust exceeds the standard during engine operation and will issue an alert immediately if it does. 2. Initially, the OBD interface was set up only to monitor the car's exhaust emissions, but in recent years, OBD has evolved through several generations, greatly enhancing its functions and roles.
117
Share

What are the methods for repairing car body dents?

Car body dent repair methods are: 1. Clean the dented area of the car with alcohol and a cleaning cloth, and mark the center of the dent; 2. Load special hot melt glue into the glue gun and preheat for 7 minutes after plugging in; 3. Select an appropriate shim and evenly apply hot melt glue from the center to the edges using the glue gun; 4. Quickly attach the shim covered with hot melt glue to the marked dent location until the glue solidifies; 5. Align the hole in the bridge-type repair tool with the firmly attached suction cup screw, tighten the nut after inserting it, and the suction cup will gradually pull up the dent; 6. Remove any residual hot melt glue from the car paint using alcohol and a plastic scraper.
118
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.