···
Log in / Register

What are the common issues with the Mitsubishi Lancer EX?

1Answers
VonStephen
07/28/2025, 07:54:34 PM

The common issues with the Mitsubishi Lancer EX are mainly as follows: 1. Various abnormal noises, especially from the center console area, and also when going uphill or accelerating. The sound insulation is poor, and the tire noise is very loud. Difficulty in engaging reverse gear. The engine coolant pipes are prone to leakage. 2. The Lancer EX is a compact sedan under the Southeast Motors brand, a joint venture model between Southeast Motors and Mitsubishi Motors. As of October 2019, the Mitsubishi Lancer EX has been completely discontinued. 3. The last model of the Mitsubishi Lancer EX was the 2016 version, launched in March 2016, all compliant with the China V emission standards, featuring a front-engine, front-wheel-drive layout. 4. The Mitsubishi Lancer EX used a total of three engines: a 1.6-liter naturally aspirated engine, a 1.8-liter naturally aspirated engine, and a 2.0-liter naturally aspirated engine. In terms of transmission, the Mitsubishi Lancer EX was equipped with a CVT continuously variable transmission and a 5-speed manual transmission.

Was this review help?
119
Share
More Q&A

What are the braking techniques for Subject 2?

Subject 2 braking techniques are as follows: 1. Familiarize with the clutch: In Subject 2, you don't need to press the accelerator, only the clutch is used to control the speed. Only by mastering the clutch can you effectively control the speed. For clutch operation, use the left heel as the pivot point, with the left forefoot fully in contact with the pedal, controlling it by lifting or pressing the forefoot. When shifting gears, quickly press the clutch all the way down and shift to the corresponding position. 2. Clutch semi-engagement: Starting with the clutch fully pressed, slowly release it. The following signs indicate that the clutch is in semi-engagement state. Before semi-engagement, the tachometer shows the engine idle speed; when the pointer or numbers drop significantly, it indicates the clutch is starting to semi-engage. When semi-engagement begins, the engine sound will also decrease along with the tachometer.
113
Share

Does the Dash Cam Still Record After the Car Power is Off?

After the car power is turned off, the dash cam can still record for about 30 seconds. This is mainly due to the residual power inside the dash cam, which is relatively low, so the recording time is also very short. Generally, the dash cam is connected to the car's battery. If the car's power is turned off and the dash cam does not have a parking recording function, it will usually stop recording after the car is parked. The dash cam is an instrument used to record video and audio during the vehicle's operation. By installing a dash cam, it can record the video and audio during driving, which can serve as evidence in the event of a traffic accident to protect the driver's legal rights. The dash cam is equivalent to the black box of a car, but the video data inside cannot be edited. Once edited, it cannot be used as evidence to assist in traffic accidents. All dash cams consist of a host, sensors, data analysis software, and an infrared camera. The video data from the dash cam can be viewed through the corresponding mobile app.
112
Share

Where is the Fog Light Switch?

Generally, the fog light activation button is located on the light control lever. Below is a detailed introduction to automotive fog lights: 1. Usage Scenarios: The most common scenario for using fog lights is in foggy conditions. Additionally, they are used in severe weather such as snow or rain, or when driving in environments filled with smoke. To ensure driving safety, front fog lights must be used for illumination, while rear fog lights should be used as needed. 2. Precautions: Front and rear fog lights should not be used unless necessary, as they lack light shields. The intense glare can affect the vision of oncoming or following drivers, potentially compromising driving safety.
112
Share

Is It Correct to Press the Clutch and Brake Simultaneously?

Pressing the clutch and brake simultaneously is not the correct practice, as it can easily shorten the lifespan of the clutch. However, this method can be used in emergency situations. When stopping the car, first press the clutch to reduce the speed and then apply the brakes. This can prevent the car from stalling suddenly. If the car is moving at a relatively high speed and needs to slow down or stop, you must either press the clutch or shift to neutral. Once the speed drops to an appropriate range, shift to the appropriate gear based on the specific speed and engine RPM, then press the brake to stop the car. If the driver needs to perform an emergency stop while driving, they can press both the clutch and brake simultaneously. This helps prevent misoperation by the driver and reduces the likelihood of the car stalling suddenly. In emergency situations, the driver is more likely to misoperate the pedals. By pressing both the brake and clutch at the same time, even if the accelerator is accidentally pressed, it will not affect the braking performance, ensuring the safety of the passengers.
119
Share

What Causes Gear Shift Jerkiness When Driving?

Every vehicle experiences some degree of jerkiness during gear shifts, though the intensity varies. Driver's control technique issues: The severity of gear shift jerkiness is closely related to the driver's control skills. If the timing of gear shifting isn't properly managed, jerkiness naturally occurs. Mismatch between RPM and gear position: Generally, at low speeds, if the engine RPM and vehicle speed just meet the shifting criteria, upshifting will produce stronger jerkiness; if the throttle is slightly larger, making both engine RPM and vehicle speed significantly exceed the shifting standard, the jerkiness during shifting will be relatively milder.
115
Share

What are the material properties of 510L steel plate?

510L is an automobile beam plate. 510- represents the lower limit of tensile strength, with the unit being N/mm2/L- representing automobile longitudinal and cross beams. Automobile beam plates are mainly used to manufacture structural components such as automobile longitudinal beams, cross beams, front and rear axles, and bumpers, with a thickness generally ranging from 4.0 to 8.0mm. It is a type of steel with high demand and strict performance requirements in automobile structural steel plates. Additional information: 1. Beam: The main load-bearing component of a truck, carrying almost the entire weight of the cargo. The quality of the beam affects the vehicle's service life and driving safety. The manufacturing of automobile beams generally adopts stamping forming technology, with bending as the main deformation method. 2. Beam plate performance: High formability requirements, meaning automobile beam steel plates must have excellent comprehensive performance, sufficient strength and toughness, and good fatigue resistance and cold formability. 3. Composite materials: To improve automobile load capacity, extend vehicle service life, and meet requirements for energy saving, material saving, and safe driving, the use of low-alloy high-strength and ultra-high-strength steel plates to produce automobile beams has become the current trend in the development of automobile beam steel.
107
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.