···
Log in / Register

Is it okay not to change the engine oil for a long time?

1Answers
Jeff
07/24/2025, 12:41:42 PM

It is not advisable to not change the engine oil for a long time. The reasons are as follows: 1. Reduced sealing effect. High-quality engine oil with appropriate viscosity can effectively seal the gaps between the cylinder block and pistons, preventing gas leakage. If the oil is not changed for a long time, it will become watery and lose its sealing function. 2. Reduced lubrication effect. The lubrication system is crucial to the engine, affecting its performance and service life. If the oil is not changed for a long time, its lubrication effect will significantly decrease. 3. Reduced cooling effect. The heat absorption and conduction properties of oil are much higher than those of water. If the oil deteriorates severely, its heat dissipation function will be greatly reduced. 4. Increased wear of components. If the engine oil is not changed for a long time, it will become ineffective and deteriorate. Instead of protecting the components, it will increase wear and damage. 5. Corrosion of internal components. If the oil is not changed for a long time, it will accumulate many impurities, such as iron filings, and may also cause corrosion of internal components. 6. Further damage to the engine.

Was this review help?
114
Share
More Q&A

What is the top speed of the Civic 1.0t?

The three-cylinder version of the Civic 1.0t with five seats fully occupied has reached a maximum speed of 207 km/h on the speedometer. Introduction to maximum speed: The best driving speed a car can achieve on a level and good road surface. It refers to the maximum speed a car can reach under windless conditions on a level, good asphalt or cement road surface. Factors affecting a car's maximum speed: The power of the car's engine, the engine's maximum torque, the speed at maximum torque, the transmission ratio of the drivetrain, driving resistance, etc. The maximum speed is measured on a flat and windless road surface with zero acceleration, so the gradient resistance and acceleration resistance are zero. Therefore, the main resistance factors affecting the maximum speed are air resistance and rolling resistance.
109
Share

Why does the Jetta's air conditioning pipe freeze?

Jetta air conditioning pipe freezing reasons are as follows: Abnormal expansion valve: The expansion valve for the low-pressure pipe freezing should be abnormal. When the expansion valve senses the low temperature inside the low-pressure pipe, it will reduce the opening of the expansion valve, so that the low-pressure pipe will not freeze. Excessive refrigerant in the system: Too much refrigerant added to the system causes excessive pressure, leading to the expansion valve remaining wide open. Excessive refrigerant flow results in the low-pressure pipe freezing. It is normal for the low-pressure pipe to collect water, but a frozen air conditioning system should stop operating if the thermistor is functioning properly. Therefore, a faulty thermistor is also a possible cause.
112
Share

Does the Mercedes-Benz C-Class have a continuous screen?

The new generation C-Class has directly skipped the 'continuous screen' center console layout of the current E-Class and S-Class. Here are the specific details: Interior Design: The interior design closely follows that of the new generation S-Class, featuring an oversized vertical screen on the center console integrated with Mercedes' latest MBUX infotainment system. Above it are three circular air vents, while the instrument panel on the left retains a rectangular design, and the steering wheel style is identical to that of the S-Class. News: Currently, there is no confirmed powertrain information for the new generation C-Class. Future domestically produced models may continue to be equipped with a 1.5T+48V mild hybrid powertrain, while higher-end versions are expected to adopt a 2.0T+48V mild hybrid powertrain, similar to the new E-Class. In terms of the transmission system, the engine will be paired with a 9AT gearbox.
114
Share

What is the reason for the Mercedes-Benz E300 Bluetooth connection failure?

Failure to connect to Bluetooth may be due to excessive connection records. Below are the specific details about Bluetooth: Excessive Records: If your phone's Bluetooth has connection records with other devices or too many connection records, it is recommended to delete previously unused Bluetooth devices and try connecting again. Mercedes-Benz E-Class: The exterior and interior of the new Mercedes-Benz E-Class remain consistent with the previously available 2019 model (pre-facelift), with changes primarily in significant adjustments to the powertrain and minor tweaks to the configuration. Method: Try connecting another phone to the car's system. If it also fails to connect, it may be due to a malfunction in the car system's Bluetooth module. You can visit the brand's after-sales service to check if it is functioning normally.
105
Share

What are the reasons why the Volkswagen Tayron's rearview mirror cannot open?

Volkswagen Tayron's rearview mirror cannot open for the following reasons: Gear mechanism damage: You can ask someone to assist in operating the rearview mirror switch inside the car while you place your hand on the rearview mirror to feel whether the motor inside is working; if you feel the vibration of the motor working but the rearview mirror does not move, it proves that the opening and closing gear mechanism is damaged. Motor circuit failure: If you do not feel the vibration of the motor working, and there is still none after tapping it a few times, it indicates a motor failure or circuit problem. Circuit issues are usually caused by a damaged switch or a blown fuse. Switch damage: First, check the fuse of the rearview mirror folding circuit. If the fuse is intact, it is highly likely that the switch is damaged.
120
Share

Reasons Why Mercedes-Benz Indicates the Tire Pressure Monitoring System Has Stopped Working?

Mercedes-Benz indicating the tire pressure monitoring system has stopped working is due to a damaged tire pressure sensor. The tire pressure sensor is used to monitor the tire pressure and is directly installed inside the tire, connected to the tire inflation port. If the tire pressure sensor is damaged while driving, it can also cause the tire pressure warning light to illuminate. For sensor damage issues, the only solution is to replace it with a new component. According to the international GBT2978-2008 standard requirements, the standard tire pressure is 2.4-2.5bar. In winter, the tire pressure should be adjusted slightly higher than the standard, approximately 0.2bar, based on the standard tire pressure of the car tires. In summer, the tire pressure can generally be slightly lower than the standard, about 0.1bar, to avoid tire blowouts due to high temperatures. Tire pressure reset method: First, turn on the ignition switch, then press and hold the tire pressure monitoring reset button until you hear a "beep" sound before releasing it. The tire pressure monitoring system will then store the current normal tire pressure data, automatically clear the previous data, and finally, the dashboard warning light will turn off, completing the tire pressure reset.
111
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.