How to Remove the Rear Seats of a Volvo XC60?

[OLaura]

To remove the rear seats of a Volvo XC60, press the latches located on both sides of the rear seats near the front seats. Taking the 2020 Volvo XC60 as an example, it is a mid-size SUV with the following dimensions: length 4688mm, width 1902mm, height 1658mm, and a wheelbase of 2865mm. The curb weight is 1801kg. The 2020 Volvo XC60 features a double-wishbone independent front suspension and a multi-link independent rear suspension. It is equipped with a 2.0L turbocharged engine, delivering a maximum horsepower of 190PS, a maximum power of 140kW, and a maximum torque of 300Nm, paired with an 8-speed automatic transmission.

[NathanFitz]

As an XC60 owner who has removed the rear seats myself, remember to turn off the ignition and disconnect the power before starting. First, locate the metal hook under the front part of the seat—it's the plastic pull ring in the gap where the seat cushion and backrest meet. Pull it upward firmly to release the front latch. Then, grasp the front of the seat cushion and lift it straight up until you hear a click, indicating the pawl has disengaged. Slide the entire seat cushion backward about 10 cm to remove it completely. Note that there are two alignment pins at the rear that must be properly aligned when reinstalling. After removal, check if the fixing hooks are deformed and clean any debris from the slide rails for smoother operation.

[PhoebeFitz]

Last time I helped a friend fix the water leakage in the back row of his Volvo, I specifically studied the XC60 seat structure. The seat is actually secured by clips, but requires finesse: first, reach into the gap at the front of the cushion with bare hands to locate the metal hooks (newer models have one on each side), then lift the front part of the cushion vertically upward. The key point—you must hear a distinct 'click' sound to confirm successful unlocking. Be careful when removing the cushion as there are wiring harnesses on the back connected to heating or sensors. For reinstallation, it's recommended to have two people work together—first align the positioning pins with the body bracket holes, then firmly press the front clips into place.

[VanTyler]

As an experienced car interior modification specialist, Volvo's rear seat design is more intricate than Japanese cars. Under the seat cushion is a spring clip + ratchet mechanism, and pulling hard may break the clips. Key steps: 1. Lift the back cushion to locate the fixing hooks; for the new XC60, hooks are in the middle of the bottom metal plate. 2. Place your palm firmly against the front section of the seat cushion and lift upwards. 3. After lifting to a 20-degree angle, pull horizontally backward. Special reminder: The B5 hybrid version cannot be operated with electricity on, as it may trigger a low-voltage alarm. After removal, it's recommended to lubricate the bracket slides with WD-40. When reinstalling the clips, ensure you hear two consecutive 'clicks' to confirm proper placement.

[King]

To install a child seat in the rear of my XC60, the seat cushion must be removed. I've figured out a simple method: brace your legs against the rear support of the cushion, insert both hands under the front edge of the cushion, and when you feel a metal bar about 1.5cm wide, grip it firmly with your fingers and lift upward. Remember to lean your body weight backward for leverage - you'll usually feel a distinct click. Older models might have pull straps on both sides, but post-2018 models use hidden hooks instead. Flipping up the cushion reveals the ISOFIX anchors, making it particularly convenient for cleaning food debris. When reinstalling, gently lower the cushion to ensure the locating pins snap into the U-shaped channels on the rails.

[McElliana]

Last month, while apprenticing at a 4S shop, I disassembled over a dozen XC60s. The seat structures fall into three categories: early models have exposed pull rings, the 2020 version features raised plastic strips in the seat seam, and the latest edition requires lifting the seat corner to reveal a metal plate. Recommended sequence: Lift the front floor mat to locate anchor points → Grip the seat frame border with five fingers → Apply vertical force to lift 5cm → Slide the entire unit backward. Important note! Rear seat removal may affect airbag systems - disconnect the battery negative terminal for safety before proceeding. If encountering resistance, avoid forceful pulling; check for debris in slide rails. Plastic rail replacement costs approximately 2000 yuan if fractured.