How to Remove the Door Panel of Baojun 730?

[LeCamila]

Method for removing the door panel of Baojun 730: 1. Remove the panel in the triangular area inside the door, which is located at the upper left corner of the door interior; 2. There is a small clip in the triangular area. After removing the clip, unscrew the fixing screw on the handle; 3. Starting from the position indicated at the lower rear or lower front corner of the front door, pry up all seven clips of the front door trim panel one by one, then use tools to remove the door panel. The Baojun 730 is a 7-seat family car under SAIC-GM-Wuling, with a body length, width, and height of 4780mm, 1820mm, and 1755mm respectively, a wheelbase of 2750mm, and a top speed of 160km/h.

[SanRonan]

I remember taking apart the door panels of my Baojun 730 several times before, and it felt quite easy. The door trim panels are usually secured with plastic clips. First, check the visible screw points on the inner side of the door, such as under the small cover of the door handle and in the corners of the storage compartment, then unscrew them with a Phillips screwdriver. Next, use a plastic pry tool to gently pry open the trim panel from the bottom or edges—avoid using gloves to prevent damage—and slowly pull it off. Inside, there are often wires connected, like the plugs for the window switch and door lock, which need to be unplugged before fully removing the panel. The clip placement on the Baojun 730 is quite well-designed. After removal, it’s best to check each clip; if any are broken, replace them (they cost just a few cents each online) to avoid rattling after reassembly. When washing the car, avoid blasting the clips directly with a high-pressure water gun—keeping them dry extends their lifespan. If you're repairing speakers or replacing parts yourself, just take it step by step. And remember, never attempt this while driving—safety first.

[EzraMarie]

As a car modification enthusiast, I always use simple tools when removing the door panels of my Baojun 730. Get a set of plastic pry tools or an old credit card, start gently prying from the bottom of the door to avoid scratching the interior surface. There are always screws hidden around the door handle—remove them first, then slowly peel off the entire panel. I noticed that most of the Baojun 730's wiring connectors are plug-and-play, so mark their positions before disconnecting to avoid incorrect reassembly. The main reasons for removing interior panels are to upgrade speakers or clean waterlogged areas—DIY saves money and adds fun. The clips are prone to breakage, so it's wise to keep some universal spares (car enthusiast groups recommend buying packs for about ten yuan). Avoid using excessive force when prying. After removal, I always check the door seal strips and clean off dust—maintaining small details helps prevent future issues.

[LaVincent]

In my experience, removing the door panel of a Baojun 730 is quite straightforward. After unscrewing all the interior screws on the door, you can easily pry open the trim panel from the corner. Be careful when unplugging the wiring harness to avoid damaging the circuits by pulling too hard. When reinstalling, make sure the clips are aligned and pressed down to prevent the door panel from becoming loose. Always check that the power is disconnected (turn off the engine and remove the key) before starting, for safety and convenience.

[LincolnDella]

Every time I remove the Baojun 730 door panel, I remind myself to pay attention to details: the screw positions vary (such as near the latch), using a flathead screwdriver and plastic pry tool; after prying open the interior trim, check if the wiring and clips are intact; Baojun models' clips are prone to aging—replace them immediately if cracked. Removal is for cleaning dirt or modifying components (like adding lighting strips), DIY saves repair costs. For regular maintenance, avoid frequently wiping clip areas with wet cloths to prevent water damage.

[Hadley]

I disassembled the door panel of my Baojun 730 at home to save money and for practicality. The steps are simple: remove the screws under the door handle cover, use a small pry tool to gently pry the edges, then pull off the interior panel and disconnect the wiring connectors. The clips often break after prolonged use, so handle them with care and keep some spare parts handy. The Baojun 730 door panel is designed for easy DIY, allowing you to repair door lock stains or install soundproofing material after removal. After cleaning, regularly check the seals to prevent moisture. Take your time and proceed step by step for the safest approach. Once removed, take the opportunity to clean the inside of the door, as accumulated dust can block the drainage holes.