···
Log in / Register

How to adjust the wipers on the BYD S7?

6Answers
EmeryLee
08/26/2025, 02:04:42 AM

The adjustment method for the BYD S7 wipers is as follows: 1. With the vehicle powered on, first move the wiper to near the edge of the windshield and then power off; 2. Open the hood, loosen the screw on the left wiper, move it to the correct position, tighten the screw, and then power on - it will automatically return to the lowest position; 3. At this point, loosen the screw on the right wiper, forcefully push the left wiper to the hidden position, and finally tighten the screw. The BYD S7 has dimensions of 4835mm in length, 1855mm in width, and 1720mm in height, with a wheelbase of 2730mm, and is equipped with a 6-speed manual transmission. The vehicle's top speed is 180 km/h, it features front-wheel drive, and the tire specification is 225/65R17.

Was this review help?
108
Share
Wren
09/08/2025, 04:44:09 AM

As a seasoned driver with three years of experience behind the wheel of a BYD S7, I've mastered the wiper controls. When you sit in the driver's seat, look to the right side of the steering wheel—the stalk with the raindrop symbol is the wiper switch. A light push upwards gives a single wipe, while pulling it all the way down turns it off. For regular rain, use the intermittent mode by pulling down to the first position. You can then rotate the small ring at the end of the stalk: turn it towards '+' for faster wipes and towards '-' for slower ones, just like adjusting the volume on a radio. In heavy rain, pull the stalk all the way down for continuous mode. Remember, the rear wiper is controlled by rotating the stalk in the opposite direction. Once, during a snowstorm, I forgot to turn off the wipers and they froze—since then, I’ve made it a habit to switch them off when parked for long periods. Oh, and to spray windshield washer fluid, pull the stalk towards you—just make sure to top up the washer fluid beforehand to avoid dry wiping, which can damage the rubber blades.

Was this review help?
11
Share
Expand All
EmmaLynn
10/22/2025, 10:02:21 PM

Last time I rode in my friend's newly acquired S7, I noticed he didn't know how to set the wipers to auto mode. Actually, the high-end models are super convenient. Just press the AUTO button at the very top of the stalk to illuminate it, and the sensor above the windshield will automatically adjust the speed based on rainfall. If you feel the sensitivity isn't enough, go to the vehicle settings - comfort settings on the central screen and slide the rain sensitivity slider to the right to the third level for maximum sensitivity. However, after using the auto mode for a long time, you need to pay attention to cleaning the sensor area. Once, a film on my roof blocked the sensor, and the wipers went crazy. When washing the car, avoid using a high-pressure water gun directly on that black square area; just wipe it with a soft cloth.

Was this review help?
16
Share
Expand All
LeHarley
12/05/2025, 09:25:33 PM

Speaking honestly from an auto repair shop technician's perspective, new car owners most often overlook wiper maintenance. The S7's washer nozzles are located at the edge of the hood - never mix tap water with washer fluid as mineral deposits will clog the nozzles. Before rainy season, remember to lift the wiper blades and wipe the rubber strips with tissue paper to remove grit. If the wipers don't clean properly when adjusting interval timing, the rubber is likely aged. Don't believe those online hacks about sanding the blades - spending a few dozen yuan on new rubber strips is the most reliable solution. Last week, a customer complained about wiper noise - upon opening the hood we found the nuts on wiper arms were overtightened during maintenance, and loosening them by half a turn fixed the issue.

Was this review help?
16
Share
Expand All
MarianaFitz
01/25/2026, 10:44:50 PM

You're looking at the silver-gray stalk on the right side of the steering wheel: the top knob adjusts the intermittent speed with 6 clock-like settings. Want to spray? Don't hesitate—pull it all the way down until you hear the motor. Here's a pro tip: after rain, want to wipe residual droplets without spraying? Gently push the stalk down three clicks then instantly return it to the off position—the wiper will make one perfect sweep and stop. In summer heat, never force dry wipers—the rubber sticking to glass may tear, so spray washer fluid first for lubrication. If the stalk gets stuck, try a 5-minute power reset—electronic systems occasionally glitch.

Was this review help?
9
Share
Expand All
Grady
04/21/2026, 04:12:33 AM

Veterans who have driven the S7 on the Yunnan-Tibet route share their off-road tips: In light rain, switch to the intermittent wiper setting at the slowest speed—the dashboard will display the gear number. When encountering heavy fog on mountain roads, don’t rely solely on wipers; turn on the front fog lights for better visibility. In extreme downpours where the wiper speed can’t keep up? Simultaneously rotate the intermittent knob with your left hand and press the wiper stalk with your right—the system defaults to the fastest action. In sub-zero temperatures, always lift the wiper blades if parked outdoors, or you risk burning out the motor fuse if they’re frozen. Once in the Gobi Desert, the washer fluid wouldn’t spray—turned out the hose had dislodged from sun exposure. Simply re-securing the soft tube near the hood hinge fixed it.

Was this review help?
7
Share
Expand All
More Q&A

Does Changing the Front Grille Affect Vehicle Inspection?

Replacing the front grille before a new car is registered does not affect the annual inspection. However, if the front grille is replaced after the new car is registered, it is necessary to re-register the modification with the vehicle management office and update the vehicle license; otherwise, it will affect the annual inspection. Regulations and purposes of vehicle inspection cycles: Vehicle inspection cycle regulations: For commercial passenger vehicles, inspections are required once a year within the first 5 years, and every 6 months thereafter. For trucks and large or medium-sized non-commercial passenger vehicles, inspections are required once a year within the first 10 years, and every 6 months thereafter. For small and micro non-commercial passenger vehicles, inspections are required once every 2 years within the first 6 years, and vehicles meeting the exemption criteria only need to apply for an inspection label. Starting from November 20, 2020, 7-9 seat non-commercial small and micro passenger vehicles (excluding vans) are included in the exemption range. Purpose of vehicle inspection: The benefits of safer driving are well understood, as during the inspection, staff will conduct a comprehensive check of the vehicle. For example, during the exterior inspection, overly dark window tints may require adjustment, as they can impair visibility during nighttime driving, increasing risks. During the on-site inspection, the chassis, braking system, and light brightness will also be checked.
116
Share

Where is the spark plug located in a sedan?

The spark plug in a sedan is generally located at the top of the engine cylinder. It can be clearly seen after removing the high-voltage ignition coil. Spark plug replacement procedure: Open the hood, lift the plastic cover of the engine, remove the high-voltage distributor wires, and mark the position of each cylinder to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. When removing them, check for any external debris such as leaves or dust, and make sure to clean them thoroughly. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the removed high-voltage distributor wires according to the firing order, and then secure the cover. Spark plug replacement interval: Under normal maintenance conditions, spark plugs should be replaced every 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type, so it is recommended to follow the user manual. Platinum spark plugs should be replaced at 40,000 kilometers, standard nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers.
101
Share

What is the normal tire pressure range for the Geely Binyue?

The normal tire pressure range for the Geely Binyue is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and decreased by 0.1 bar in summer. This data complies with the international GBT2978-2008 standard. The Binyue's tire pressure monitoring system is an indirect type, meaning it does not have tire pressure sensors and cannot directly display the tire pressure values. To check the tire pressure, first prepare a tire pressure gauge, locate the factory tire pressure label, press the gauge onto the tire valve to measure and read the value, and remember to replace the valve cap after measurement. Generally, a tire pressure above 2.8 bar is considered too high, and a pressure below 2.0 bar is too low. Hazards of overinflated tires: Reduced tire friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread pattern, shortening tire lifespan; increases vehicle vibration, indirectly affecting the lifespan of other components; overextends the tire cords, reducing elasticity and increasing the load on the vehicle during driving. Hazards of underinflated tires: Increases the friction coefficient with the road surface, leading to higher fuel consumption; makes the steering wheel heavy and prone to deviation, compromising driving safety; increases movement in various parts of the tire, causing abnormal heat due to excessive rolling; weakens the function of the cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, damaging the tire bead and causing abnormal wear; multiplies the friction between the tire and the ground, rapidly increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving under these conditions may lead to a blowout. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no stamp on top, four small spikes at the bottom, and an exclamation mark inside), it is generally due to one of the following three reasons: Abnormal tire pressure: The system typically alerts when the pressure is below 1.8 bar or above 3.0 bar. In this case, the tires should be checked and the pressure adjusted. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure monitoring system is not reset, it will continue to display the previous data, causing the indicator light to stay on. Simply reset the tire pressure monitoring system to resolve this issue. Damaged tire pressure sensor: The tire pressure sensor, which monitors tire pressure, is installed inside the tire and connected to the inflation valve. If the sensor is damaged due to impact while driving, the tire pressure warning light will activate. In such cases, the only solution is to replace the sensor with a new one.
101
Share

What is the difference between a motorcycle E license and a D license?

Permitted vehicle types are different. D license: ordinary three-wheeled motorcycles and E; E license: ordinary two-wheeled motorcycles and F. Below is the relevant information: Motorcycle driving license D: With a motorcycle driving license D, you can drive ordinary three-wheeled motorcycles, ordinary two-wheeled motorcycles, and light motorcycles, while an E license only permits driving ordinary two-wheeled motorcycles and light motorcycles. In other words, the motorcycle driving license D allows driving one more type of motorcycle than the E license, which is the three-wheeled motorcycle. Currently, many people taking the motorcycle driving test generally choose the D license. A1: Large passenger vehicles (A3, B1, B2, C1, C2, C3, C4, M).
116
Share

What Does Engine Seizure Mean in Cars?

Engine seizure refers to a situation where the engine temperature becomes excessively high, causing the piston to expand due to insufficient cooling from engine oil and become stuck in the cylinder, resulting in engine failure. In severe cases of engine seizure, when the cylinder pressure is too high and the piston cannot move, thick flames may be ejected. The following are the causes of engine seizure in cars: 1. Poor engine cooling efficiency: This is mainly due to the use of materials with inadequate heat dissipation properties during the manufacturing process, causing the engine's operating temperature to exceed the designed tolerance. 2. Inaccurate engine ignition timing: This occurs when the air-fuel mixture entering the engine is too rich or when ignition occurs too early.
120
Share

Can a Driver's License Be Transferred to Another Location for Learning?

Yes, here is the relevant information: The definition of a driver's license in China: A motor vehicle driver's license is a legal document issued by the administrative authorities, permitting individuals who have legally learned to drive motor vehicles, mastered traffic regulations and driving skills, and passed the required exams to operate specific types of motor vehicles. Exam content: The test subjects include traffic regulations and related knowledge, field driving, and road driving (including safe and civilized driving). The order of the test subjects is as follows: traffic regulations and related knowledge (referred to as Subject 1 [theory]), field driving (referred to as Subject 2 [nine items]), and road driving (referred to as Subject 3 [road test and safe and civilized driving]).
106
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.