···
Log in / Register

How many people take the test in one session of Subject 2?

6Answers
Shelby
07/23/2025, 06:06:45 PM

It is necessary to specify the city and the specific test center, as the scale of test centers varies. Below are the precautions for Subject 2 test: Reversing into the garage: The main points for deduction include pressing the line while reversing, the car not entering the garage, exceeding the time limit, and not following the designated route. Reversing into the garage must be completed within 210 seconds; exceeding the time limit results in a failing grade, as does not following the sequence. Pay attention to the 30cm margin issue when reversing. Parallel parking: The main points for deduction include the turn signal, 30cm margin, and pressing the line. Right-angle turn: The main points for deduction are the turn signal and pressing the line. Operating the turn signal incorrectly after entering the test area deducts 10 points.

Was this review help?
115
Share
OEliza
08/10/2025, 01:51:27 PM

I remember when I was taking the Subject 2 test, there were about 15 people in my session. We were queuing up in the test area, and the atmosphere was quite tense. We waited nearly two hours before it was our turn. The examiner said each test site has limited parking spaces, with a maximum of 20 people, so they could carefully monitor each one to prevent safety incidents. I took the test in a big city where there were more people, while a friend in a smaller area had only 10 people in their session. I recommend you register for off-peak hours in advance to avoid wasting time like I did. For test items like reverse parking, too many people can be distracting and affect performance. If the examiner is efficient, a session can be completed within 15 minutes. During regular practice, ask your instructor more questions—they know the actual situation of the test site and can help you avoid pitfalls.

Was this review help?
16
Share
Expand All
AustinFitz
09/23/2025, 01:57:01 AM

In my experience, the number of candidates per session for Subject 2 usually ranges between 10 and 20 people. It depends on the size of the test site and the number of examiners—generally, one examiner is responsible for 8-10 candidates. Larger test sites can accommodate more. Last time I took the test in the suburbs, there were only 12 people in my session, and the time was well-distributed, so I didn’t wait too long. In crowded urban test sites, it can go up to 25 people, but mistakes are more likely. The tests are scheduled in batches to avoid congestion, so don’t worry about too many people. A few experienced drivers I know mentioned that each candidate averages about 5 minutes, so proper scheduling is key. When you register, you can check local driving association info—maybe a less crowded time slot will improve your chances. After the test, chat with others about your experience; it helps ease the pressure for everyone.

Was this review help?
19
Share
Expand All
Willis
11/06/2025, 03:12:48 AM

The number of candidates for the Subject 2 driving test is usually around 12 per session. The test regulations are set for safety reasons, and the examiner can monitor the entire process. Based on my research at the test site, the number may reach 18 during peak periods, but the maximum is 30. A larger number of candidates can increase pressure and may slightly lower the pass rate. It is recommended that candidates choose to take the test during off-peak seasons to minimize distractions. During the test process, there are time limits for each section of the course, and candidates take turns performing tasks such as reversing. Understanding the rules is crucial; if the test goes smoothly, there won't be any time overruns, and fewer candidates make the process more manageable.

Was this review help?
5
Share
Expand All
SanPaislee
12/27/2025, 10:09:48 PM

From what I've observed, each session of Subject 2 (Parking Test) typically accommodates around 15 candidates, with slight variations depending on test site conditions and daily schedules. Each parking bay operates independently, with one examiner supervising 10 candidates, ensuring sufficient time allocation. Overcrowding can affect efficiency – during my observation on test days, sessions with fewer candidates showed lower error rates. Driving schools coordinate information to avoid batch conflicts, making advance booking a wise choice. Bringing beverages for the wait helps maintain composure. Proper scheduling can improve pass rates, allowing candidates to tackle test items with ease.

Was this review help?
19
Share
Expand All
VanDakota
03/25/2026, 01:17:57 AM

When my child took the Subject 2 driving test, there were 12 people in one session, and the test center administrator said the standard is 10-20 people. That day, there weren't many people, so it was easier to pass, and the examiner was more focused on each reversing maneuver. Waiting a bit longer during the test is normal; everyone queues up and takes turns. When the weather is bad, there are fewer people, and suburban test centers are better. It's recommended to schedule the test during less crowded periods to reduce anxiety. Those who have taken the test several times say that sessions with fewer people are easier to pass, and their mindset is more stable. Sharing more experiences makes preparation easier.

Was this review help?
20
Share
Expand All
More Q&A

What is the Difference Between 92 and 95 Octane Gasoline?

92 octane gasoline and 95 octane gasoline differ mainly in their formaldehyde content. 95 octane gasoline contains more isooctane. Below is a detailed introduction about engine oil: 1. Overview: Engine oil, also known as engine lubricant, is referred to as Engine-oil in English, with a density of approximately 0.91×10³ (kg/m³). It serves to lubricate and reduce friction in the engine, assist in cooling, seal against leaks, prevent rust and corrosion, and provide shock absorption. 2. Composition: Engine oil consists of two parts: base oil and additives. The base oil is the main component of lubricating oil, determining its basic properties. Additives can compensate for and improve the shortcomings of the base oil's performance, imparting certain new properties, making them an important part of lubricating oil.
105
Share

How to Install Tire Pressure Monitoring System on Kia K3?

Installation method for tire pressure monitoring system on Kia K3: Remove the original valve and replace it with a valve equipped with tire pressure sensor. There are two types of tire pressure monitoring systems: direct tire pressure monitoring system and indirect tire pressure monitoring system. The Kia K3 is a compact car with body dimensions of 4600mm in length, 1780mm in width, and 1445mm in height, with a wheelbase of 2700mm. The Kia K3 is equipped with two engines: a 1.5-liter naturally aspirated engine and a 1.4-liter turbocharged engine. The 1.5-liter naturally aspirated engine has a maximum power of 85 kW and a maximum torque of 143.9 Nm; the 1.4-liter turbocharged engine has a maximum power of 96 kW and a maximum torque of 211 Nm.
108
Share

What Are the Causes of Abnormal Noise in a Car Clutch?

Abnormal noise in a car clutch may be caused by clutch wear, control unit failure, etc. Here is a detailed introduction to car clutches: 1. Overview: The car clutch is located inside the flywheel housing between the engine and the transmission, and the output shaft of the clutch is the input shaft of the transmission. During driving, the driver can press or release the clutch pedal as needed to temporarily disconnect or gradually engage the engine and transmission, thereby cutting off or transmitting the power input from the engine to the transmission. 2. Principle: The driving and driven parts of the clutch transmit torque through friction between contact surfaces, use liquid as a transmission medium, or employ magnetic transmission (electromagnetic clutch). This allows temporary disconnection and gradual engagement, while permitting relative rotation between the two parts during transmission.
116
Share

What is the difference between cold testing and hot testing?

Cold testing refers to linkage testing, which is system testing without materials. Hot testing refers to feeding testing, which is system testing with materials and will involve chemical reactions. The following is a detailed introduction about car driving: 1. Overview: Car driving is one of the basic skills that modern people need to master. To master the technology of driving a motor vehicle, one must meet the required age and physical conditions, and undergo training and examination on road traffic safety laws and regulations, as well as general knowledge about automobile mechanics and safe driving. 2. Others: The permission to drive a vehicle is granted through the issuance of a driver's license. This indicates that obtaining a driver's license is a formal procedure that must be issued by a specialized authority.
105
Share

What Causes Difficulty in Pressing the Clutch Pedal?

Clutch pedal difficulty can be attributed to the following specific reasons: 1. Poor Return: Air entering the clutch hydraulic system leads to excessive clutch travel and poor return, primarily caused by air intrusion into the hydraulic system. In this case, the cause of air intrusion should be identified promptly, and the air in the hydraulic system should be purged. 2. Contaminated Fluid: Severe wear of the internal piston in the clutch master cylinder or blockage of the return oil hole prevents the clutch from returning. 3. Insufficient Spring Tension: As the vehicle mileage increases, the clutch return spring may lose tension or break, causing the clutch pedal not to return. The symptom is a lowered clutch pedal height with reduced or no free play, making the pedal feel harder to press.
119
Share

Should You Press the Clutch or Brake First When Stopping on a Slope in Subject Two?

When stopping on a slope in Subject Two, you should press the clutch first. Here is a detailed introduction about the car clutch: 1. Overview: The car clutch is located inside the flywheel housing between the engine and the gearbox, and the output shaft of the clutch is the input shaft of the gearbox. During driving, the driver can press or release the clutch pedal as needed to temporarily separate or gradually engage the engine and the gearbox, thereby cutting off or transmitting the power from the engine to the gearbox. 2. Principle: The driving part and the driven part of the clutch transmit torque through friction between contact surfaces, or use liquid as a transmission medium, or use magnetic transmission (electromagnetic clutch) to allow temporary separation and gradual engagement, while permitting mutual rotation between the two parts during transmission.
120
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.