···
Log in / Register

how much is a second hand ps3

1Answers
LoganLee
12/10/2025, 10:09:10 PM

In the USA, a second-hand PlayStation 3 typically sells for around $50 to $150, depending on the model, condition, and included accessories. Older or lower-end units, like slim or super-slim versions, usually range from $50 to $80, while well-maintained or more desirable models with extra controllers or games can reach $100 to $150.

Was this review help?
120
Share
More Q&A

How can I test Mircom MIX-DH3000 Series Alpha Intelligent Duct Detectors without cover removal?

You can test the Mircom MIX-DH3000 Series Alpha Intelligent Duct Detectors without removing the cover, thanks to the built-in "Test Port Valve." This patented feature, as detailed in the Mircom MIX-DH3000 Series Alpha Intelligent Duct Detectors Instruction Manual, enables aerosol smoke testing. This design allows for convenient and efficient functionality checks, ensuring your detectors are operational and ready to identify smoke.
117
Share

How do I configure the binary address of the ALCN-792M/ALCN-792MISO Quad Loop Adder Module using DIP switches for my fire alarm system?

To set the binary address of your ALCN-792M/ALCN-792MISO Quad Loop Adder Module, follow these steps: First, locate the DIP switches, labeled SW1-1 to SW1-8, on the module. These switches control the binary address. Each switch represents a binary digit. An "ON" position activates the digit and an "OFF" position deactivates it. Consult the DIP switch settings table in the module's manual. This table provides the specific switch configurations for each address. For instance, to assign address "2", set SW1-1 to "OFF", SW1-2 to "ON", and SW1-3 through SW1-8 to "OFF". Always double-check your DIP switch settings to confirm the correct binary address has been assigned. Finally, complete the adder module installation and wiring, adhering to the guidelines in your Network Fire Alarm Manual. Correctly configuring the binary address is crucial for the proper function of your ALCN-792M/ALCN-792MISO Quad Loop Adder Module within your fire alarm system.
106
Share

How to mute the microphone on SteelSeries 61650 Tusq earbuds?

To mute your microphone using the SteelSeries 61650 Tusq In-Ear Mobile Gaming Earbuds, locate the Microphone Mute Switch directly on the earbuds. Simply flick this switch to the mute position. This is a quick and easy way to silence your microphone during gaming sessions or calls, ensuring your privacy and preventing unwanted background noise from being transmitted.
114
Share

How do I safely clean the glass panels on my IKEA KULINARISK Convection Oven door?

Cleaning the glass panels of your IKEA KULINARISK Convection Oven door requires a careful approach. Here’s a step-by-step guide based on the oven's manual: Begin by turning off the oven and allowing it to cool completely. Open the oven door fully and hold both hinges securely. Lift and pull the latches on the hinges until you hear them click. Partially close the oven door, moving it to the first opening position. Then, lift and pull to detach the door from its frame. Place the door on a soft cloth on a stable surface. Locate the door trim (identified as 'B') along the top edge of the door. Gently push inwards on both sides of the trim to release the clip seal. Pull the door trim forward to remove it. Hold the glass panels by their top edges and carefully slide them out one by one, starting with the top panel. Ensure each glass panel fully slides out of its supports. Clean the glass panels using a solution of water and soap. Dry them thoroughly. Important: Do not clean the glass panels in a dishwasher. After cleaning, reassemble the oven door by reinstalling the glass panels, the door trim, and the door itself. Close the latches on both hinges; a distinct click confirms proper installation.
115
Share

How can I synchronize multiple Potter GTSM modules for fire alarm system operation?

To synchronize multiple Potter GTSM Synchronization Control Modules for coordinated operation of your strobes and horn/strobes, follow these guidelines. First, designate one module as the master and the others as slaves. The sync input of each slave module should be wired to the sync output of the master module. The sync input terminals are electrically isolated, which allows slave modules to connect to different power supplies and panels. The wiring between the sync modules (sync + and - terminals) is supervised, ensuring proper operation. Keep in mind that the sync input and horn input terminals draw a 7mA load at 24VDC, so confirm your power supply can handle the load. If a slave module loses the sync signal from the master, it will operate independently. The horns on slave modules can be muted individually via the horn input on each slave module, while a mute signal from the master mutes all slave modules. For staggered zone power-up, all units will resynchronize with the master within four seconds if a slave module is powered on after the master. A green LED status indicator on the module will flash every four seconds if zone 1 is operational and twice every four seconds if both zones 1 and 2 are operating correctly. For optimal synchronization, ensure the master control module is powered on at the same time or before the slave modules.
115
Share

How do I safely replace the battery in my Eterna PRCIRMW3 LED Circular Bulkhead?

Replacing the battery in your Eterna PRCIRMW3 LED Circular Bulkhead requires following these steps for safety and proper function. Always begin by switching off the electricity at the mains, including both the permanent live and switch live, and allow the existing batteries to completely discharge. Once this is done, you can proceed with the replacement. First, remove the diffuser. Then, take the battery case out of the gear tray and remove the old battery, carefully cutting the wires. Before installing the new battery, write the current date on it. Next, fit the new 3.2V 1500mAh Lithium battery, ensuring you use a suitable connector. After the new battery is in place, refit the gear tray and the diffuser. Restore the power supply and allow the unit to charge for 24 hours. Following the replacement and charging, it's essential to perform a comprehensive operation check and update your test record. If, after following these steps, the light does not remain lit for a full 3-hour test period, consider the need for further inspection. Remember to allow the unit to charge for a full 24 hours after the replacement is complete.
112
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.