···
Log in / Register

Why is the Replacement of Internal Combustion Engines by Electric Vehicles Inevitable?

1Answers
OJulian
07/29/2025, 06:11:56 AM

Because electric vehicles have lower operating costs, lower maintenance costs, are quieter, faster, and respond more quickly than internal combustion engine vehicles. The following are the reasons why electric vehicles will replace internal combustion engine vehicles: 1. National policy: The country advocates energy conservation and environmental protection, reducing losses and pollution. 2. Natural reasons: Petroleum is a non-renewable resource, and global reserves are decreasing. 3. Cost advantages: Under the same maximum output power level, the cost of the motor itself is very low, and the pure electric power system has a lower efficiency advantage. 4. Maintenance and lifespan advantages: The price of electric vehicles will decrease, meeting most driving needs, with lower operating costs, lower maintenance costs, and being quieter and faster.

Was this review help?
111
Share
More Q&A

What is the service life of automotive compressed natural gas cylinders?

GB-17258-1998 "Steel Cylinders for Compressed Natural Gas as Automotive Fuel" does not specify the service life, but in practice, they are scrapped after 10 years. Additional information is as follows: Relevant regulations: GB-17258-1998 "Steel Cylinders for Compressed Natural Gas as Automotive Fuel" does not specify the service life, but in practice, they are scrapped after 10 years. In August 2003, Beijing Tianhai Industry Co., Ltd.'s enterprise standard Q/JBTHB014-2003 "Periodic Inspection and Evaluation of Steel Cylinders for Compressed Natural Gas as Automotive Fuel" clearly stated: "For cylinders used in taxis for more than 5 years and in other vehicles for more than 10 years, they will not be inspected after registration and will be scrapped.
118
Share

What octane gasoline should be used for a 2013 RAV4 Rongfang?

13-year-old RAV4 Rongfang should use 92-octane gasoline. The following is a related introduction to the 2013 2.0L manual two-wheel-drive urban version RAV4 Rongfang: 1. Power system: equipped with a 2.0L naturally aspirated 4-cylinder 6ZR-FE engine, paired with a 6-speed manual transmission. 2. Body dimensions: length, width, and height are 4570mm, 1845mm, and 1670mm respectively. The wheelbase is 2660mm. 3. Chassis: the drive mode is front-wheel drive, the front suspension is MacPherson independent suspension, and the rear suspension is double-wishbone independent suspension.
119
Share

Why doesn't the Kia Sportage automatically roll up windows after locking?

The Kia Sportage does not automatically roll up windows after locking because it lacks this feature. Here are detailed explanations about it: 1. Explanation one: The Sportage is equipped with multiple high-tech features such as hill-start assist and downhill assist systems, fully realizing the vehicle's intelligence. The design of the front face is a highlight of the car, with the elongated lines of the headlights giving a sense of refinement, and when viewed from another angle, the curved shape becomes apparent. 2. Explanation two: With body dimensions of 4400x1855x1660mm, it fits the standard size of a city SUV and is larger than the previous generation Sportage.
106
Share

How Long Does the Smell Last After Removing Car Film?

The smell after removing car film usually disappears in about three days. The lingering odor after film removal and adhesive cleanup is mainly caused by the following reasons: 1. Incomplete adhesive removal: The adhesive exposed to the air can continue to emit unpleasant odors. For example, the rear windshield is not flat and has fragile heating wires, making it difficult to completely remove the adhesive, which can lead to residue. 2. Incorrect adhesive removal method and inadequate protective measures: Residue from the adhesive can seep into other areas of the car. If the film is of poor quality and you attempt to remove it yourself, this situation is more likely to occur. 3. Low-quality car film: Poor-quality adhesive in the car film contains volatile gases such as formaldehyde and benzene. Prolonged exposure to sunlight causes these gases to "have nowhere to hide," leading to film bubbling and continuous emission of unpleasant odors inside the car. Once the film is removed, formaldehyde and other gases are released all at once, not only being extremely foul-smelling but also irritating, enough to make one's eyes water. Therefore, some professionals wear masks when removing film to protect themselves.
103
Share

Which fuse is for the Chery QQ3 wiper?

The fuse for the Chery QQ3 wiper is located in the fuse box under the steering wheel. Below are detailed explanations about it: 1. Explanation one: The purpose of the fuse is to prevent circuit overload. Vehicles usually have two fuse boxes, each responsible for protecting different circuits. 2. Explanation two: There are two types of automotive fuses: high-current and low-current fuses. However, medium and low-current fuses are more common in cars, and the wiper fuse belongs to the blade-type fuse. 3. Explanation three: Always use the wiper when there is rain. The wiper blade is designed to clear rainwater from the windshield. Do not use it when there is no rain, and never operate it dry. Running the wiper without water increases friction resistance, which can damage the rubber wiper blade and the wiper motor.
101
Share

How far should the front of the car be from the wall to avoid hitting it when turning the steering wheel to the full lock?

As for the question of how far the front of the car should be from the wall to avoid hitting it when turning the steering wheel to the full lock, it actually depends on the length of the vehicle and the timing of turning the wheel. If the car is longer, the distance from the wall should be greater. Similarly, if the steering is turned earlier, the car should also be farther from the wall. Therefore, there is no fixed value for this distance. Additional information is as follows: 1. Technique: You can treat the inner corner as the wall corner. Before entering the curve, first drive close to the right side of the lane, aligning the right 1/3 of the car hood with the right edge of the road, ensuring the right side of the car is about 30 cm from the edge. When the left rearview mirror is parallel to the inner corner, you can turn the steering wheel fully to the left. At this point, the car will not hit the inner corner, meaning it won't hit the wall corner. 2. Vehicle condition: In reality, the width of the road is wider than that in the driving test (Subject Two), so following the Subject Two method ensures you won't scrape the wall corner in real situations. If turning the steering wheel fully to the left, always monitor the front of the car and the rearview mirror, constantly checking the condition of the left side of the car. Slow down or even stop if necessary. Similarly, if turning the steering wheel fully to the right, observe the right front of the car and the right rearview mirror, and check through the rear window if needed.
107
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.