···
Log in / Register

Why does the car make a clunking sound when turning?

1Answers
StMartin
07/29/2025, 04:08:12 AM

The reasons for the clunking sound when the car turns are: 1. The sound from the turn signal returning to position. If the turn signal is activated while turning, this sound could be from the return clip of the turn signal's automatic return mechanism; 2. Aging of the steering tie rod ball joint; 3. Steering gear failure. If the abnormal noise is very loud during turning, it might be caused by excessive gear clearance in the steering gear, requiring replacement of the steering gear; 4. Abnormal noise from the stabilizer bar. Loose or damaged stabilizer bar bushings not only produce noise when turning but also when driving on uneven roads. Loose stabilizer bar bushings can be fixed by adding shims.

Was this review help?
106
Share
More Q&A

How to Manually Deactivate the Lavida Anti-Theft System?

When the door lock is disabled, an alarm will sound. Use the key to open the driver or passenger door, then wait a few minutes for the alarm to stop. Open the engine hood and locate the alarm, typically found below the steering wheel, then turn it off. Find the fuse box and remove the fuse belonging to the alarm. If none of the above methods work, you can disconnect the battery. Alternatively, take it to a repair shop for professional assistance in removing the alarm, then simply reinsert the fuse without damaging the wiring.
112
Share

What to Do When the Side of a Tire is Cut Open?

Utilize the friction from the ground to loosen the tire bolts in a counterclockwise direction using a wrench in a diagonal pattern. After loosening the bolts, locate the chassis frame and use a jack to lift the side with the damaged tire. There is usually a corresponding slot on the chassis for the jack. Lift the vehicle until the tire is about a finger's width off the ground, then remove all the bolts. Take out the spare tire, align it with the bolt holes, and fasten the bolts in a diagonal pattern. Remove the damaged tire from under the vehicle, retract the jack, lower the tire to the ground, and finally tighten all the bolts.
118
Share

How to Reset the Maintenance Light on the Dorcen G60s?

Turn on the ignition switch, hold down the "Reset Button 5" with one hand, and turn off the ignition switch with the other hand. Keep holding the "Reset Button 5" without releasing it until the clock and mileage on the dashboard completely disappear (there should be no display on the dashboard), then release the button. Press and hold the "Reset Button 5" again with one hand, then turn on the ignition switch. At this point, the maintenance reminder on the dashboard will flash. Continue holding the "Reset Button 5" without releasing it until the maintenance reminder stops flashing, then release the button. Turn on the ignition switch or start the vehicle again to check if the reset was successful.
116
Share

How to Read Mileage Information from a BMW Key?

First, press the ignition switch twice and wait for the car to respond before proceeding with the following steps. Hold down the central locking button, then press the ignition switch once and immediately release the ignition switch. After that, release the central locking button. This step is crucial: place the key against the marked area on the steering column and hold it there for a few seconds to allow the information to transfer. Wait for 3-5 seconds until you hear a beep, indicating that the data transfer was successful. At this point, you have successfully retrieved the mileage information from the BMW key.
120
Share

What to Do When a Passat Lingyu Emits Blue Smoke During Cold Start?

Remove the camshaft and hydraulic tappets, use a wrench to remove the spark plugs, and adjust the piston of the corresponding cylinder to top dead center. Screw the pressure hose into the spark plug threaded hole. Bolt the spring compression tool onto the cylinder head. Adjust the valves to the correct position, then connect the pressure hose to the air compressor. Use a threaded mandrel and thrust piece to press down the valve spring and remove it. Gently tap the valve spring seat to remove the valve lock, then pull out the valve stem oil seal. Place the plastic sleeve onto the valve stem, lightly apply a layer of engine oil to the oil seal lip, and slowly push it onto the valve guide.
120
Share

How to Remove and Install the Fuel Pump on an Older Land Cruiser Prado 4000?

Prepare the tools needed for fuel pump removal, then position the vehicle on a level indoor surface, turn the ignition switch to OFF, and engage the parking brake. Remove the rear seat cushion of the vehicle, and use tools to carefully detach the rear access cover. Disconnect the cable from the negative terminal of the battery, and remember to wrap the disconnected fuel lines with plastic wrap. Using a screwdriver with protective tape wrapped around its head, disconnect the fuel pump filter hose, and carefully remove the fuel pump downward. Disconnect the fuel pump wiring harness, remove the fuel pump O-ring, and place the fuel pump in a clean parts tray.
109
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.