···
Log in / Register

Where is the VIN and engine number stamped on the Fengjun 5?

4Answers
VonDerek
09/03/2025, 11:33:34 PM

The VIN of the Fengjun 5 is located under the hood; the engine number is stamped at the lower right corner of the cylinder block. More information about the Fengjun 5 is as follows: 1. The Great Wall Fengjun 5 is a pickup truck under the Great Wall brand, meeting both passenger and cargo transportation needs. 2. The new Fengjun 5 retains the same exterior design as the current model, featuring a rugged overall appearance with a full bumper and headlight design that gives it a youthful look. 3. In terms of power, it continues to be equipped with a 2.0T diesel engine, 2.5T diesel engine, 2.8T diesel engine, and 2.2L/2.4L gasoline engine, paired with a 5-speed manual transmission.

Was this review help?
117
Share
TravisLee
09/16/2025, 12:42:11 AM

When I used the Great Wall Wingle 5 for transportation before, I often needed to check the VIN. The stamped number is actually quite hidden. It's located behind your right front wheel - you'll need to crouch down to see the area around the chassis beam, look near the shock absorber spring. First wipe away grease and dust with a cloth, then the stamped number will be visible. Remember to bring a flashlight, as it's hard to see in poor lighting. A tip: if the vehicle is too dirty to see clearly, first brush gently with a soft-bristled brush before wiping - never scrape hard as you might wear away the stamped numbers. The DMV also mainly checks this spot during inspections because it's more reliable than the paper label under the windshield. Make it a habit to clean this area during regular maintenance so you can find it quickly in emergencies.

Was this review help?
14
Share
Expand All
VonMicah
10/30/2025, 01:17:15 AM

Last year during the annual inspection of my father-in-law's Great Wall Wingle 5, we spent quite some time searching for the VIN stamp. Eventually found it at the rear section of the engine bay. When you pop the hood, don't rush to look at the engine - crouch down and check near the firewall towards the cabin. There's a set of raised numbers on the black metal frame. The location is roughly on the longitudinal beam directly behind the clutch pedal, requiring you to lean sideways to see it. If it's rainy and the car's muddy, better skip DIY searching and just drive to a repair shop for a lift inspection. Regular rust prevention for this area is crucial - if the stamp gets covered by rust, it becomes problematic. Heard some newer models might have it relocated near the left front wheel, but older versions mostly keep it on the right side.

Was this review help?
4
Share
Expand All
HannahMarie
12/13/2025, 12:25:14 AM

Once when helping a friend transfer ownership of a Fengjun 5, I realized the VIN stamp isn't in an obvious spot. Check near the brake pedal under the steering wheel - the 17-digit code is stamped on the right-side metal frame. It's located slightly inward from the door sill trim, requiring removal of plastic covers for clear visibility. Best viewed in early morning when sunlight angles make recessed characters more visible. If struggling, use a selfie stick to record video and zoom in. Note this must match the windshield sticker code - discrepancies may indicate frame tampering. Check stamp clarity biannually; take rubbings if wear appears.

Was this review help?
3
Share
Expand All
More Q&A

What Causes the Vibration in a Haval H9 While Driving?

Haval H9 vibration while driving may be caused by: 1. Dirty throttle body, excessive carbon deposits in the fuel injector or intake tract; 2. Check the oxygen sensor; 3. Regularly replace the three filters (engine oil filter, air filter, and fuel filter) which must be periodically changed during vehicle usage. Taking the 2020 Haval H9 gasoline 4WD Elite model as an example, it features a 5-door, 5-seat mid-to-large SUV body structure with dimensions of 4856mm in length, 1926mm in width, 1900mm in height, a wheelbase of 2800mm, an 80-liter fuel tank capacity, and a curb weight of 2285kg.
114
Share

What is the method for removing the plastic shell of the trunk?

The method for removing the plastic shell of the trunk is: 1. Locate the two clips next to the interior panel; 2. Then remove the interior panel from the clips. Maintenance methods for the trunk: 1. When cleaning, use a brush to remove dirt, including the edges and grooves of the trunk, and perform odor treatment after cleaning; 2. Use separate bags for organizing items; 3. Lay a trunk mat to prevent dirt or liquids from entering and corroding the trunk surface. Solutions for a trunk that won't close: 1. Lubricate and adjust the trunk; 2. Clean the trunk's slot; 3. Replace the spring rod with one of moderate hardness; 4. Check if there is a fault in the trunk's control circuit; 5. Replace the trunk's hydraulic support rod.
116
Share

What Causes the Steering Wheel Return Noise in BMW 7 Series?

BMW 7 Series steering wheel return noise may be caused by plastic friction, steering column rubbing against floor mats, faulty clock spring, or aging tie rod ends. Plastic friction: Especially in new cars, the steering wheel consists of various plastic components. If the gaps between these components are too small, friction will occur during steering wheel rotation. This usually resolves after a break-in period. Steering column rubbing against floor mats: This mainly occurs when aftermarket floor mats are too large and come into direct contact with the steering column, causing friction as the column rotates. Faulty clock spring: This happens when the clock spring is broken or its connector is unplugged. The solution is to replace or secure it. Aging tie rod ends: Replace the tie rod ends, but a wheel alignment is required after replacement.
107
Share

How to Turn Off the Rear Wiper on an Audi?

Audi rear wiper shut-off method: 1. Locate the wiper control lever below the right side of the steering wheel; 2. Push the wiper lever to the 'OFF' position. The function of wipers is to remove raindrops, debris, and dust adhering to the vehicle's windshield, thereby improving driver visibility and enhancing driving safety. Steps for replacing car wipers: 1. Lift the wiper arm; 2. Press the tab underneath to release the wiper blade. Car wiper replacement procedure: 1. Lift the wiper arm; 2. Press the lower tab to detach the wiper blade; 3. Remove the old wiper; 4. Pry up the front end of the center clip; 5. Insert the new wiper into the center clip, pull firmly until hearing a click sound to complete installation.
120
Share

How to Turn on the Air Conditioning Cool Air in Geely Binyue?

Geely Binyue is equipped with automatic air conditioning. Press the AUTO button to activate the automatic mode of the air conditioning. At this time, the Binyue's air conditioning system will automatically control the airflow and mode based on the conditions inside the car. If you need to turn on the cool air, press the AC button, while for warm air, there is no need to press the AC button. Taking the 2020 Binyue as an example, it is a compact SUV with a wheelbase of 2600mm, a fuel tank capacity of 45L, and a curb weight of 1310kg. The 2020 Binyue features a MacPherson strut independent front suspension and a torsion beam non-independent rear suspension. It is powered by a 1.4T turbocharged engine with a maximum horsepower of 141PS, a maximum torque of 235Nm, and a maximum power of 104kW, paired with a 6-speed manual transmission.
102
Share

Is the license plate in Changsha Xiang A?

Changsha's license plate is Xiang A. The license plate codes for various regions in Hunan are as follows: Xiang A for Changsha, Xiang B for Zhuzhou, Xiang C for Xiangtan, Xiang D for Hengyang, Xiang E for Shaoyang, Xiang F for Yueyang, Xiang G for Zhangjiajie, Xiang H for Yiyang, Xiang J for Changde, Xiang K for Loudi, Xiang L for Chenzhou, Xiang M for Yongzhou, Xiang N for Huaihua, Xiang S for provincial systems, and Xiang U for Xiangxi Tujia and Miao Autonomous Prefecture. The vehicle registration agency code consists of 2 characters, comprising a Chinese character and an English letter. The Chinese character represents the abbreviation of the province, autonomous region, or municipality directly under the central government, while the English letter denotes the code of the vehicle management office. When assigning English letter codes for license plates, the letters I and O are skipped to avoid confusion with the Arabic numerals 1 and 0.
101
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.