···
Log in / Register

Where is the fuse box located in the Jeep Compass?

6Answers
GarrettAnn
07/29/2025, 03:48:15 PM

The fuse box of the Jeep Compass is located under the left side of the driver's seat. If any electrical equipment stops working during use, it may be due to a blown fuse and should be replaced promptly. When replacing, first turn off the ignition switch and open the fuse box cover, then replace the fuse. Fuse replacement method: To remove a fuse in the Jeep Compass, you do not need to pull it out directly by hand. Each fuse box is equipped with tweezers for removing fuses. Both ends of the tweezers can be used to remove large and small fuses. Use the extraction tool to remove the fuse and install a new one. Precautions for replacing fuses: Replace the fuse according to the rated current value indicated on the fuse box cover. If the new fuse blows immediately, it indicates that there may be a fault in the circuit system, and it should be repaired as soon as possible. In the absence of a spare fuse, a temporary replacement can be used in an emergency. If a fuse with the same current load cannot be found, a fuse with a lower rated current than the original can be used as a substitute.

Was this review help?
120
Share
AlexFitz
08/14/2025, 11:22:15 AM

My Jeep Compass has been running for five years, and I'm quite familiar with the fuse box locations. There are two fuse boxes in the car: the one in the engine compartment is on the left near the windshield, and you can see the black square box with clips when you open the hood. The one in the cabin is below the steering wheel, and you need to pry open the left storage compartment first to see the plastic cover. I've replaced the cabin fuse myself using the small clip that comes with it. Here's a reminder: when checking, make sure the car is turned off and the key is removed, and replacements must use fuses with the same amperage. Last time, a friend replaced a 20-amp fuse with a 30-amp one, which ended up burning out the wiper motor—it's no joke.

Was this review help?
7
Share
Expand All
RoseAnn
10/15/2025, 03:29:16 AM

After years of working on cars, I'm very familiar with the location of the Jeep Compass fuse boxes. The engine compartment fuse box is located at the front left of the engine, usually next to the battery. Lift the black cover to reveal four rows of fuses. For the cabin fuse box, you'll need to crouch down and look at the lower left corner of the steering wheel. First remove the plastic storage compartment (use some finesse to release the clips on both sides), and you'll see three neatly arranged rows of fuses inside. I always remind car owners: use professional plastic tweezers to replace fuses - never use metal tweezers; turn off all power before removing or inserting fuses; it's best to take photos to record original positions as installing in wrong slots may cause other functions to fail.

Was this review help?
14
Share
Expand All
DelEliza
11/28/2025, 03:21:02 AM

When I first bought my Compass, I also looked for the fuse box. The one in the engine compartment is located at the lower left side of the windshield, and you can easily spot the square black box once you open the hood. The interior fuse box is behind the storage compartment on the lower left side of the steering wheel—just pull it outward with a bit of force to remove it. I’d advise ladies not to replace fuses themselves, as the position is quite deep and requires half-lying down to operate, making it easy to strain your back. Last time, the cigarette lighter fuse in my car blew, and a quick 10-minute visit to the auto repair shop fixed it—much more cost-effective than struggling for hours and breaking the storage compartment.

Was this review help?
14
Share
Expand All
Robin
01/18/2026, 09:56:37 PM

When doing modifications, it's often necessary to tap into the fuse box for power. The engine compartment fuse box in the Jeep Compass is the easiest to locate—just open the hood and look for the black plastic box in the upper left corner. The cabin fuse box is a bit trickier to find; you'll need to remove the storage compartment to the left of the steering wheel (insert your fingers into the gap and pull toward yourself). A detail I noticed when installing a dash cam myself: the fuse box position varies slightly by model year, shifting a few centimeters. The 2020 model sits about two finger-widths higher than older versions. Before tapping for power, I recommend using a multimeter to check the current direction—connecting to constant power can drain the battery, as I learned the hard way when my car wouldn't start the next day.

Was this review help?
3
Share
Expand All
OmarMarie
04/14/2026, 11:16:31 PM

Veteran Driver's Advice: No matter which generation of the Compass, the locations of the two fuse boxes remain largely unchanged. The one in the engine bay is hidden behind the coolant reservoir—just lift the rubber cover with the fuse symbol. The one in the cabin is located near the knee area, requiring the removal of the small storage compartment with the Jeep logo (turn counterclockwise and pull out). A reminder to everyone: clean the fuse box regularly. Once, I found my power windows weren’t working, and it turned out the fuse contact surface was covered in dust. Before you start, prepare a fuse puller and replacement fuses—don’t make the same mistake I did last time by using a toothpick, which got stuck inside and couldn’t be removed.

Was this review help?
12
Share
Expand All
More Q&A

How to Charge a 12V Battery?

12V battery charging method: Attach the red clamp of the charger to the battery's positive terminal marked with a plus sign, and the black clamp to the negative terminal marked with a minus sign. Starting batteries sometimes become discharged due to heavy usage or prolonged storage, so they should be periodically removed from the equipment and recharged in a charging area. Supplementary charging is generally performed once a month to enhance reliability and extend service life. It is advisable to perform a supplementary charge before winter. Battery charging precautions: Initial charging: The first charge of a battery is called the initial charge, which significantly impacts the battery's lifespan and charge capacity. Insufficient charging results in lower charge capacity and shorter lifespan, while overcharging improves electrical performance but also shortens lifespan. Therefore, new batteries should undergo initial charging carefully. Dry-charged lead-acid batteries: For dry-charged lead-acid batteries, as per the user manual, if used within two years of storage, simply add the specified density of electrolyte and let it stand for 15 minutes before use without charging. However, if stored for more than two years, partial oxidation may occur on the plates. To improve charge capacity, a supplementary charge of 5-8 hours is recommended before use. Scheduled charging: When not in use for extended periods, aim to perform a health charge once a month or discharge to 50% after full charge. The optimal ambient temperature for battery charging is 25°C, which is difficult to achieve in cold winters, so indoor charging is preferable. If conditions don't permit, choose to charge during sunny daytime hours to enhance battery activity and reduce range loss.
110
Share

How to Remove a Car Washer Nozzle?

Introduction to the method of removing a car washer nozzle: Generally, washer nozzles come with reverse clips. You can press the reverse clips on both sides with a flat tool to remove the nozzle. Wipers, also known as windshield wipers, are devices used to wipe away raindrops and dust attached to the vehicle's windshield, improving the driver's visibility and increasing driving safety. Due to legal requirements, almost all cars are equipped with wipers. Solutions for a clogged washer nozzle: 1. Check if your car's washer fluid reservoir has water. Ensure there is water before wiping the windshield; otherwise, it may burn out the wiper motor. 2. If the washer fluid reservoir has water and the motor is working, but the wipers are not spraying water, the nozzle may be clogged. 3. Take a paperclip, straighten it, and gently insert it into the nozzle, stirring back and forth. 4. Choose a paperclip with a diameter suitable for the nozzle's outlet hole size. Avoid using excessive force, as it may damage the outlet hole. 5. Avoid dry wiping the windshield. Always spray water while wiping to prevent scratches on the glass.
101
Share

How Many Liters of Antifreeze Are Generally Needed?

Generally, antifreeze requires about 5-7 liters. The amount of antifreeze to be added varies for each vehicle. After adding antifreeze, you can check the scale on the auxiliary water tank. Typically, there are two marks on the auxiliary water tank: one for the maximum level and one for the minimum level. The antifreeze must be between these two marks—neither too much nor too little. Below is more detailed information: 1. The engine's antifreeze must have characteristics such as freeze protection, boil-over prevention, corrosion resistance, scale prevention, and no foam formation, and it should not be affected by seasons or regions. Among these, the freezing point and boiling point are the basic indicators of antifreeze. 2. The coolant is prepared by mixing antifreeze with water in a certain ratio. Automobile manufacturers usually specify the mixing ratio for different low-temperature antifreeze grades in the user manual and also designate the type of antifreeze, which should not be mixed. The full name of antifreeze should be antifreeze coolant, meaning it is a coolant with antifreeze functionality. Antifreeze can prevent the coolant from freezing and cracking the radiator or damaging the engine cylinder block or head during cold winter parking.
116
Share

What does the P in automatic transmission mean?

P stands for Parking—the parking gear, where P is the abbreviation. After parking, it is necessary to engage the P gear to prevent the vehicle from rolling, especially when parking on a slope. The general method to engage P gear is to press the brake pedal and wait until the vehicle comes to a complete stop before shifting or using the electronic button for models equipped with one. Automatic transmissions have the following gears: 1. P gear: Represents the parking gear. When parking the vehicle, shift into P gear, including when shutting off the engine or during prolonged idling. 2. R gear: Represents the reverse gear. Shift into R gear when reversing the vehicle. 3. N gear: Represents the neutral gear, which is the same as the neutral gear in manual transmissions. It can be used for short-term parking. 4. D gear: Represents the drive gear. When shifted into this gear, the vehicle moves forward. In this gear, the transmission automatically shifts between 1st and the highest gear based on the vehicle's speed and throttle conditions. 5. S gear: Represents the sport mode. When shifted into this gear, the transmission delays shifting, keeping the gear at higher RPMs for longer to increase vehicle power, though this naturally consumes more fuel.
116
Share

What is the correct method to check car engine oil?

Correct methods to check car engine oil include the smell test, the rub test, the color test, and the light test. The engine needs sufficient oil for lubrication, but more is not always better. Insufficient oil can cause serious damage to engine components due to poor lubrication. Correct methods to check car engine oil: Smell test: Pull out the dipstick and bring it close to your nose. If there is a strong acidic or foul smell, it indicates the oil has deteriorated and should be changed. Rub test: Take some old oil and rub it between your thumb and forefinger repeatedly. Good-quality oil will feel smooth, produce little residue, and have no gritty feeling. If you feel impurities, poor viscosity, or even a rough texture, it's time to change the oil. Color test: Place a few drops of old oil on a clean white filter paper. After the oil spreads, good-quality oil will leave no powder, feel dry and smooth to the touch, and show a clear yellow diffusion ring. If the oil appears dark brown with visible impurities, it should be replaced. Light test: Hold the dipstick at a 45-degree angle under light and observe the oil droplets. If you can clearly see no metal particles, the oil is still good. If there are many particles, the oil should be changed.
109
Share

Can an automatic car be shifted into neutral while driving?

Automatic cars should not be shifted into neutral while driving. Here are the reasons: 1. Shifting an automatic car into neutral while driving will reduce the vehicle's braking force, which can easily lead to rear-end collisions. When the car is coasting in neutral, the connection between the engine and the drive wheels is lost, and the car moves forward solely by inertia. In emergency situations requiring braking, all braking force must be provided by the brakes alone. When coasting in gear, the engine itself provides some braking effect, which, combined with the brakes, shortens the braking distance. Additionally, coasting in neutral can easily cause the engine to stall, leading to failure of the brake booster and reduced braking performance. 2. Shifting into neutral does not save fuel and can sometimes even consume more fuel, which is related to the working principle of electronic fuel injection engines. Electronic fuel injection engines can determine the amount of fuel injection based on the computer program. When coasting in gear, if the driver releases the accelerator, the computer will put the car into coasting mode, during which the engine does not inject fuel for a long period. However, if coasting in neutral, the computer will put the car into idle mode, and the engine continues to inject fuel. This is why coasting in neutral sometimes consumes more fuel.
112
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.