···
Log in / Register

Where is the Chery Antifreeze Located?

6Answers
McBrody
07/29/2025, 10:00:00 AM

Chery's antifreeze filling port is located in the engine compartment. Pay attention to the oil reservoir and water reservoir. There are two filling ports for water. The antifreeze filling port is located above a small water reservoir, while the windshield washer fluid is on top and does not have a visible small water reservoir; it is marked with a water spray pattern on the cap. Vehicle antifreeze generally needs to be replaced every 2 years or 40,000 kilometers. This is just a reference interval. For commercial vehicles with longer mileage, the replacement interval should be shorter. Since driving conditions vary for each vehicle, the replacement should be based on actual usage. Check the antifreeze condition regularly. If the antifreeze level is low, replenish it promptly. If suspended particles, sediment, or discoloration are observed, replace the antifreeze and clean the system immediately. How to determine if antifreeze is low: Check the antifreeze warning light on the dashboard. If it lights up, it likely indicates low antifreeze, though it could also be due to excessively high cylinder temperature. Inspect the antifreeze reservoir. If the fluid level is below the minimum mark (MIN), do not continue driving and add antifreeze promptly. Check the water level markings on the antifreeze reservoir. The antifreeze level should normally be between the maximum and minimum marks. If it is below the minimum mark, it indicates a shortage of antifreeze.

Was this review help?
116
Share
MaryLee
08/13/2025, 01:39:18 AM

After driving Chery cars for so many years, I've noticed that the coolant reservoir is always tucked away in a corner of the engine bay. Specifically, when you pop the hood, it's typically located at the front right near the windshield – a translucent plastic tank with MIN and MAX indicator marks on its sight window for easy fluid level checks. My advice: always turn off the engine and wait for it to cool before inspecting to avoid burns. Never delay refilling when low; top up with the same-colored coolant to the MAX line to maintain peak cooling system performance. Chery's reservoir design is generally stable – my Tiggo series' unit hasn't moved positions in years. Just remember to replace the fluid every two years or so to prevent corrosion or leaks that could compromise engine longevity.

Was this review help?
19
Share
Expand All
VonGemma
10/10/2025, 02:29:19 AM

As someone who enjoys hands-on car maintenance, I find the antifreeze reservoir quite easy to locate in Chery vehicles: pop open the hood and look for the small round or square tank near the upper left corner of the radiator, typically a green or pink fluid container labeled 'COOLANT'. For safety, I always wait at least two hours after turning off the engine before touching it to avoid hot steam burns; the fluid level should be within the normal range when cold, otherwise poor heat dissipation can lead to overheating—an embarrassing situation if it happens mid-drive. Also, always top up with the manufacturer-specified type and avoid mixing different colored fluids to prevent chemical reactions that could clog the pipes. A quick glance at the reservoir before driving is a low-cost habit that prevents major headaches.

Was this review help?
6
Share
Expand All
DiLincoln
11/23/2025, 02:40:52 AM

As a new driver, I recently learned how to locate the antifreeze in my Chery car: After lifting the hood, it's positioned near a plastic box at the front left side - a small transparent reservoir that lets me easily check the fluid color as a beginner. The best time to inspect is in the morning when the engine is cold; test the tank opening temperature with your finger to ensure it's cool. If the level is low, slowly pour in factory-approved fluid of the matching color. Remember to maintain it regularly to keep your car running efficiently.

Was this review help?
18
Share
Expand All
Tucker
01/13/2026, 09:24:41 PM

The antifreeze reservoir in a Chery vehicle's engine compartment is typically located in the expansion tank area, near the fan or the upper part of the radiator. It is a transparent plastic container with a graduated scale to help monitor the fluid level. Its design allows drivers to easily identify and check, ensuring the engine operates at the proper temperature. Abnormal fluid levels may indicate system leaks or water pump issues, requiring prompt investigation. It is recommended to check during each maintenance cycle to prevent damage to the powertrain due to insufficient cooling.

Was this review help?
19
Share
Expand All
HaydenFitz
04/10/2026, 12:40:54 AM

I always pay attention to the details of my car. The position of the Chery coolant reservoir is usually in the front center or prominent left side of the engine compartment, a plastic tank marked with MAX/MIN for daily monitoring of the fluid level. Adding coolant of the same color safely with the tank cap open when the engine is cold can avoid the danger of overheating. Regular inspection of this component can extend engine life, saving money and providing peace of mind.

Was this review help?
4
Share
Expand All
More Q&A

Where are the accelerator, brake, and clutch pedals located in a car?

In a car, the clutch pedal is on the left, the brake pedal is in the middle, and the accelerator pedal is on the right. Below are some precautions regarding the operation of the accelerator and clutch pedals. 1. Starting: When starting a manual transmission car, it is essential to use the clutch properly. The key points for operating the clutch pedal during starting are: quick initial lift, slow adjustment when reaching the semi-engagement point, and coordinated movement. Initially, lift the clutch pedal quickly, then slow down the lifting speed when the semi-engagement state is reached. While lifting the clutch pedal, gradually press the accelerator pedal according to the engine resistance to ensure a smooth start. Mastering this technique helps avoid stalling the engine while driving. 2. Gear shifting while driving: When shifting gears during driving, the clutch pedal must be pressed. The clutch pedal should be pressed and released quickly without lingering in the semi-engagement state, as this can accelerate clutch wear. Pay attention to coordinating the accelerator during gear shifts. Inaccurate coordination between the accelerator and clutch may result in jerky gear shifts, causing wear to the car's transmission and reducing ride comfort. Some experienced drivers use the double-clutching method during gear shifts, but this is not recommended for novice drivers. 3. Pressing the clutch when stopping: The clutch should be pressed when stopping the car in daily driving. Not using the clutch when stopping can easily lead to stalling, cause impact on the transmission, and in severe cases, affect the engine's lifespan, increasing the owner's maintenance costs. Proper use of the clutch ensures smooth and stable stopping.
108
Share

What is the function of an automotive oil filter?

Automotive oil filter is used to: filter the engine oil, improving its cleanliness and lubricity, thereby reducing engine wear and ensuring optimal performance. The automotive oil filter, also known as the oil filter, operates similarly to the circulatory system of the heart—the oil in the oil pump continuously circulates, during which many impurities are generated, requiring the oil filter to remove them. Recommended replacement interval for automotive oil filters: replace every 5,000 to 10,000 kilometers driven. It is advisable to replace the oil filter every time the engine oil is changed because contaminants in the old oil filter can reduce the viscosity and cleanliness of the new oil, affect oil circulation speed, and potentially damage the engine.
117
Share

How to Adjust the Date on a Dash Cam?

To adjust the date on a dash cam: Click the menu on the dash cam, find the settings option, select the date and time settings, and adjust the time to the current accurate time. Reasons for incorrect dates on dash cams: 1. Dead battery: The dash cam does not retain time memory when powered off; replacing the battery will solve the issue. 2. Loop recording time setting: If set too short or too long, it may cause time desynchronization; setting an appropriate loop recording time will resolve this. The main functions of a dash cam are to record road conditions, prevent fraud, serve as evidence for liability determination in case of accidents, and capture scenic views during the journey.
112
Share

What is the fault when the excavator safety lock is opened but there is no action?

Excavator safety lock opened but no action fault diagnosis. Check hydraulic oil level: Blocked hydraulic circuit suction filter, oil circuit suction vacuum (including excessively low hydraulic tank oil level) can cause insufficient oil suction or even failure to draw oil in the hydraulic pump. These will directly lead to insufficient oil pressure in the hydraulic circuit, resulting in no movement of the excavator. This type of fault can be diagnosed by checking the hydraulic tank liquid level and the contamination degree of the hydraulic oil. Check if the hydraulic pump has malfunction: Hydraulic excavators generally use 2 or more main pumps to supply pressurized oil to the system.
112
Share

Does the Classic Sylphy have ESP?

Classic Sylphy does not have ESP. ESP stands for Electronic Stability Program, which helps maintain optimal vehicle stability under various conditions, particularly effective in cases of oversteer or understeer. More information about ESP is as follows: 1. The ESP system is essentially a traction control system. Compared to other traction control systems, ESP not only controls the drive wheels but also the non-drive wheels. 2. For example, in rear-wheel-drive vehicles that often experience oversteer situations where the rear wheels lose control and cause the car to fishtail, ESP will brake the outer front wheel to stabilize the vehicle. In cases of understeer, to correct the tracking direction, ESP will brake the inner rear wheel to adjust the driving direction.
117
Share

How Many Horsepower is 124kw?

124kw is equivalent to 168 horsepower. Power is a crucial performance parameter of an engine, measuring the amount of work done by the engine per unit of time. The higher the power, the more work the engine can perform within a given time frame. Greater power also translates to better acceleration performance in vehicles. Another important performance parameter of a car's engine is torque, which measures the output moment per work cycle. Automotive power refers to the work done by the vehicle per unit of time, indicating the work performed by an object within that period. Higher power results in greater torque, enhancing the vehicle's pulling force. Maximum power is commonly used to describe a car's dynamic performance.
115
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.