···
Log in / Register

What type of engine oil should the Arrizo 5 use?

1Answers
Eileen
08/28/2025, 10:04:10 PM

Arrizo 5 uses 5w30 engine oil. The method for changing its engine oil is as follows: 1. Lift the vehicle with a jack, locate the oil drain bolt, and loosen it to drain the oil; 2. Remove the oil filter and place a container beneath it; 3. Replace with a new oil filter and add new engine oil. The Arrizo 5 is a compact car with body dimensions of: length 4572mm, width 1825mm, height 1482mm, wheelbase 2670mm, and a fuel tank capacity of 48l. It is equipped with a 1.6l naturally aspirated engine, with a maximum power output of 66kw and a maximum power speed of 6150rpm.

Was this review help?
106
Share
More Q&A

What is the purpose of the line on the car rearview mirror?

The line on the rearview mirror is used to identify distance and position. Here is an introduction to the functions of the rearview mirror: 1. The rearview mirror reflects the situation behind, beside, and below the car, allowing the driver to indirectly see these areas clearly; 2. It expands the driver's field of vision, enhancing safety during reversing and driving. Here is additional information on how to adjust the rearview mirrors: 1. Left-side exterior rearview mirror: Adjust the horizon reflection in the mirror to the center, and position the reflection of the left side of the car to occupy the right quarter of the mirror; 2. Right-side exterior rearview mirror: Adjust the horizon reflection in the mirror to two-thirds of the mirror's height, and position the reflection of the right side of the car to occupy the left quarter of the mirror.
108
Share

What car is featured in Wolf Warrior 2?

The off-road vehicle in Wolf Warrior 2 is the domestically produced BAIC BJ40L. BAIC's technology: The previous generation Mercedes-Benz GLS technology platform was provided to BAIC. However, even so, after the launch of the BJ90, it will become the most luxurious SUV among China's independent brands and perhaps one of the most expensive SUVs. BAIC's structure: In terms of engine, transmission, and chassis, the BAIC BJ90 is identical to the Mercedes-Benz GLS. Mercedes-Benz has been generous to BAIC. However, it is certain that BAIC purchased ready-made engines, transmissions, and chassis, with Mercedes-Benz directly exporting these three major components from overseas to China for assembly by BAIC, rather than BAIC producing them independently.
117
Share

Why does the fan only start working at the third speed setting but not the first?

Fan not operating at the first speed setting but only starting at the third speed is caused by a decrease in the capacitance of the fan starting capacitor. Replacing it with a capacitor of the same capacity will resolve the issue. Below is relevant information about automotive cooling fans: 1. Axial fans: The blades of an axial fan push air to flow in the same direction as the axis. The impeller of an axial fan somewhat resembles a propeller. During operation, the majority of the airflow moves parallel to the axis, meaning along the axial direction. The power consumption of an axial fan is lowest when the inlet airflow is free air at 0 static pressure, and it increases as the back pressure of the airflow rises during operation. 2. Centrifugal fans: When a centrifugal fan operates, its blades push air to flow in a direction perpendicular to the axis (i.e., radially). The intake is along the axial direction, while the exhaust is perpendicular to the axial direction.
101
Share

Is the first maintenance better at 3,000 kilometers or 5,000 kilometers?

The first maintenance is better at 3,000 kilometers, and the first maintenance at six months/5,000 kilometers should be the limit. The following is a related introduction to the first maintenance: 1. Running-in period: Precautions for driving before the first maintenance. The initial driving period of a new car is called the running-in period. Generally, you should not drive too fast, absolutely do not exceed 100 mph, and the engine speed should not exceed 3,000 rpm; A well-run-in vehicle will have a lower probability of problems in future driving and will also be more fuel-efficient. 2. First maintenance time: The first maintenance service for a new car is usually provided free of charge by the 4S store, and the time is according to the regulations in the car maintenance manual, which varies for each model.
102
Share

What does 'hand-operated clutch' mean?

For individuals with leg disabilities who cannot operate the clutch pedal with their feet, the clutch is modified to be positioned above and operated by hand through a backward pulling motion, hence termed as 'hand-operated clutch'. Location of the clutch: The clutch is situated within the flywheel housing between the engine and the transmission. The clutch assembly is secured to the rear plane of the flywheel with screws, and the output shaft of the clutch serves as the input shaft of the transmission. Usage of the clutch: During vehicle operation, the driver can depress or release the clutch pedal as needed to temporarily disconnect or gradually engage the engine with the transmission, thereby interrupting or transmitting the engine's power to the transmission. The clutch is a common component in mechanical transmission systems, allowing the drivetrain to be disconnected or engaged at any time.
110
Share

What does engine compression ratio mean?

Engine compression ratio refers to the degree to which the engine's air-fuel mixture is compressed, expressed as the ratio of the total cylinder volume before compression to the cylinder volume after compression (i.e., combustion chamber volume). Additional information: 1. The vast majority of automobiles use so-called "reciprocating engines", where a piston in the engine cylinder performs linear reciprocating motion repeatedly in cycles. Therefore, within these continuous working strokes, there is a specific range of motion. 2. For a particular engine cylinder, when the piston reaches its lowest point, this position is called bottom dead center, and the entire cylinder volume including the combustion chamber forms the maximum stroke volume. When the piston moves in the opposite direction and reaches the highest point, this position is called top dead center, resulting in the smallest volume condition during the entire piston stroke. The compression ratio to be calculated is the ratio of this maximum stroke volume to the minimum volume.
113
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.