What is the reason for the sudden failure of the Magotan's auto start-stop function?

1 Answers
LeEmersyn
07/30/25 12:06am
Magotan's auto start-stop function suddenly not working may be due to the function being turned off or temporarily suspended when the battery power is insufficient. Below is relevant information about the engine auto start-stop system: 1. The engine auto start-stop system automatically shuts off the engine when the vehicle comes to a temporary stop (e.g., at a traffic light) and automatically restarts the engine when it's time to move forward again. 2. STT is short for STOP&START. The STT intelligent fuel-saving system is a set of controls for engine start and stop. The system uses a computer to determine the vehicle's status, such as when the vehicle is idling at a red light or in traffic congestion. The computer can then control the engine to automatically stop running without affecting the use of in-car air conditioning, audio, and other equipment. This technology can save about 5% of fuel under normal road conditions and up to about 15% in congested road sections.
Was this review help?
12
2
Share
More Forum Discussions

How to Open the Hood of a Great Wall H6?

Method to open the engine hood of the Great Wall Haval H6: The switch is located at the lower left side of the driver's compartment; pull it to open. To close the engine hood of the Great Wall Haval H6: Remove the support rod from the opened hood and press it downward to close. Below is some related information about the Haval H6: 1. The Haval H6 is a compact SUV under the Haval brand. 2. The low-power version of the 1.5-liter turbocharged engine has a maximum power of 110 kW and a maximum torque of 210 Nm. 3. The high-power version of the 1.5-liter turbocharged engine has a maximum power of 124 kW and a maximum torque of 285 Nm.
7
4
Share

What is the displacement of 1.6xl?

1.6xI represents a displacement of 1.6 liters, where xI denotes the configuration. Here are detailed explanations about displacement: 1. Displacement is a crucial parameter of an engine. Generally, engines with larger displacement have stronger power but also higher fuel consumption. 2. Engines with larger displacement intake more air, thus requiring more fuel to mix with the air for combustion. Displacement refers to the total volume between the top dead center and bottom dead center of all cylinders in an engine. 3. Before turbocharging technology was widely applied in automotive engines, most car manufacturers increased engine power by combining supercharging with larger displacement. However, after turbocharging technology matured, many manufacturers began using turbocharging to enhance engine power.
1
5
Share

What Does the Second Car Maintenance Include?

The second car maintenance includes servicing the transmission, engine, body suspension, braking and steering systems, as well as tires, etc. If the inspection and maintenance during the second service are done properly, it can significantly improve the overall vehicle condition and greatly enhance driving safety. The specific items for the second car maintenance are: 1. Change the engine oil, oil filter, and fuel filter. 2. Check tire pressure to ensure it is normal. 3. Inspect the suspension arms and shock absorbers to ensure they are securely fixed and functioning properly, with the wheel hub bearings not overheating after driving. 4. After performing the 'three cleans and three filters' operation on the engine, check that it starts easily, runs smoothly, has normal exhaust, and that the coolant temperature and oil pressure meet requirements. Ensure the engine speed is stable, there are no abnormal noises, all belts are properly tensioned, and there are no leaks of water, oil, electricity, or gas. 5. Check that the steering free play and toe-in meet requirements, ensuring the steering is light, flexible, and reliable, with no wobbling or deviation of the front wheels during driving. 6. Verify that the clutch free play meets requirements, ensuring the clutch is easy to operate, fully disengages, engages smoothly and reliably, with no abnormal noises, and no oil leaks in the hydraulic system. 7. Inspect the transmission, drive axle, or half-shaft drive device to ensure good lubrication, secure connections, no abnormal noises or overheating, smooth gear shifting without jumping or oil leaks.
19
4
Share

What is the real driving range of the NIO ES6?

The real driving range of the NIO ES6 is approximately 300 kilometers. Here are the details about the NIO ES6: 1. Body dimensions: The NIO ES6 has a length, width, and height of 4850/1956/1758mm, and comes with 255/55-R19 tires across all variants. 2. Powertrain: The NIO ES6 is equipped with a dual permanent magnet synchronous motor setup, delivering a total power output of 320kW and a total torque of 610Nm. 3. Charging time: The NIO ES6 supports fast charging in 0.8 hours and slow charging in 12 hours. 4. Drive system: The NIO ES6 features an electric all-wheel-drive system.
18
4
Share

How to Turn on the Hazard Warning Lights?

The hazard warning light button is located in the center of the dashboard, featuring a red triangle symbol. Press it to activate. Additional information about hazard warning lights is as follows: 1. Hazard warning lights, commonly known as emergency flashers or 'double flash', are technically termed as hazard alert lights. 2. Hazard warning lights represent the highest level of warning signals. Many drivers instinctively turn them on during heavy fog, though this practice is prohibited in some countries as it makes it difficult for following vehicles to discern the leading vehicle's direction. 3. Never use hazard warning lights while changing lanes. Avoid lane changes in foggy conditions whenever possible. If lane change is necessary, turn off the hazard lights and use turn signals instead. When driving on highways, it's recommended to activate turn signals 500 meters before changing lanes or exiting via ramps.
3
1
Share

Why Does a Motorcycle Wobble When Hands Are Off the Handlebars?

Specific reasons are as follows: 1. Loose bolts: These bolts include front and rear axle nuts, swingarm pivot nuts, steering stem nuts, shock absorber mounting bolts, and other bolts directly related to the motorcycle's stability. Each of these bolts and nuts plays a significant role. 2. Excessive clearance in the motorcycle: Excessive steering stem clearance, excessive front and rear wheel bearing clearance, or excessive swingarm clearance can all cause this issue. Excessive wear can also affect the motorcycle's stability. 3. Deformation of corresponding motorcycle parts: Improper operation by the rider or other reasons during use can lead to deformation of the front and rear wheels, front shock absorbers, or the motorcycle frame. 4. Motorcycle tire pressure: The air pressure in the front and rear tires must be appropriate. Otherwise, both over-inflation and under-inflation can cause the motorcycle body to wobble. Additionally, loose spokes or wheels can also lead to handlebar wobbling.
20
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.