···
Log in / Register

What is the MIIT fuel consumption of the Terra?

1Answers
Gary
07/29/2025, 12:34:22 AM

2020 2.5L manual two-wheel drive Terra has a MIIT comprehensive fuel consumption of 8.9L. 2020 2.5L automatic two-wheel drive Terra has a MIIT comprehensive fuel consumption of 9.2L. The following are related introductions about fuel consumption: 1. Habits and road conditions: Fuel consumption is greatly related to driving habits and road conditions. Avoid heavy acceleration and start gradually for the most fuel efficiency. To save fuel, avoid pressing the accelerator heavily when starting, as heavy acceleration consumes 2 to 3 times more fuel than normal starting speed. 2. Braking: Maintaining distance and avoiding frequent braking saves more fuel. If you don't maintain distance, you may need to brake frequently on the road. When braking, the automatic transmission will downshift, and the car will have to accelerate again from a lower gear. Starting from a standstill or low gear requires the engine to consume more fuel.

Was this review help?
116
Share
More Q&A

Will There Be Any Impact If a Car Is Not Driven for a Month in Summer?

Not driving a car for a month can cause problems. Leaving a car unused for an extended period can be harmful. If the vehicle must be parked for a long time, it is best not to leave it outdoors. A better option is an underground garage or a relatively enclosed space. The issues that may arise from not driving a car for a month include: 1. Component and Rubber Aging: When a car is parked for a long time, electronic components are more prone to moisture damage, and rubber parts may accelerate aging due to exposure to wind and rain. These conditions can significantly reduce the car's waterproofing and soundproofing capabilities. 2. Battery Drain: A car's battery gradually charges while the vehicle is in use. However, if the car is left unused for an extended period, such as a month, the battery remains in a state of continuous discharge without recharging. This is mainly due to devices like the anti-theft module, which continue to operate even after the engine is turned off.
120
Share

What is the fuel tank capacity of the NV200 in liters?

The NV200 has a fuel tank capacity of 55 liters, as officially published. The NV200 uses 92-octane gasoline, with a fuel consumption of 6.9L per 100 kilometers. A full tank can provide a driving range of approximately 797 kilometers. During daily driving, it is essential to monitor the remaining fuel level in the tank. This is typically done by observing the fuel gauge inside the vehicle. Under normal circumstances, the fuel gauge accurately reflects the fuel level. Most fuel gauges have 5 to 6 segments. It is recommended to refuel when only 2 segments remain to avoid running out of fuel mid-journey. During actual refueling, the amount of fuel added may exceed the nominal tank capacity. This is because the manufacturer's specified tank capacity is measured from the bottom of the tank to the safe fill level, leaving some space between the safe fill level and the tank opening. This extra space accommodates fuel expansion due to temperature increases, preventing overflow. If fuel is filled up to the tank opening, the actual refueled amount may exceed the nominal tank capacity.
103
Share

Is a tire temperature of 60 normal in summer?

Tire temperatures between 90-110 degrees Celsius are considered normal, and a tire temperature of 60 degrees is not a cause for concern. Tires are equipped with insulation sleeves that generally keep the temperature within a controllable range. Additionally, excessively high tire temperatures can be very dangerous. Here are some methods to prevent car tire blowouts: Maintain normal tire pressure: Manufacturers provide standard tire pressure values, which should not be too high or too low. High pressure can easily lead to blowouts, while low pressure can also cause blowouts when the tire temperature rises. It is recommended to use tires of the same model and tread pattern for the vehicle: Especially, the front two wheels and rear two wheels should not use different types of tires. Regularly inspect tires: Repaired tires should not be used as front tires. Tires with tread crowns punctured by hard objects over 5mm, side punctures, tread depth below 1.6mm, or cracks and damages at the bead should be replaced promptly. Check the tread: Look for embedded stones or foreign objects. Ensure the spare tire maintains proper pressure. Use a pry bar to tap the tire—if the sound is crisp or the rebound is good, it's fine; if the sound is dull, inflate it promptly.
113
Share

Start the Engine First or Depress the Clutch?

Depress the clutch first before starting the engine. Below is relevant information about the clutch: Clutch: The clutch is located within the flywheel housing between the engine and the transmission. The clutch assembly is secured to the rear plane of the flywheel with screws, and the output shaft of the clutch serves as the input shaft of the transmission. While driving, the driver can depress or release the clutch pedal as needed to temporarily disconnect or gradually engage the engine and transmission, thereby cutting off or transmitting the engine's power to the transmission. The principle of releasing the clutch: The principle of releasing the clutch is: 'Slow at first, quick in the middle, and coordinated at the end.' When initially depressing the pedal, do it quickly and press it all the way down in one motion. When lifting the pedal, move quickly during the free travel phase, slow down as it nears engagement, pause slightly at the semi-engagement point, and then release it completely. The key to this process is accurately identifying the semi-engagement point. To control the vehicle speed effectively, treat the semi-engagement point as the dividing line—lifting quickly above it and lowering slowly below it, adjusting downward to select a speed that suits you.
102
Share

What is the difference between 3-cylinder and 4-cylinder engines?

The differences between 3-cylinder and 4-cylinder engines: 1. Manufacturing structure: The 3-cylinder turbocharged engine has a simpler manufacturing structure, is smaller in size than a 4-cylinder engine, and is lighter in weight. 2. Acceleration: The 4-cylinder turbocharged engine performs better in terms of starting and acceleration, and its stability is superior to that of the 3-cylinder engine. 3. Operation state: The 3-cylinder engine operates in an unbalanced state, making it more prone to vibration compared to the 4-cylinder engine. 4. Noise: The 3-cylinder engine is louder than the 4-cylinder engine, and despite the use of balance shaft technology, the issue remains unresolved. 5. Displacement: 4-cylinder engines are typically used in cars with a displacement of 1.3L or more, offering greater displacement and naturally more horsepower compared to 3-cylinder engines.
120
Share

How to Determine if a Vehicle is China 5 or China 6?

Methods to distinguish between China 5 and China 6 vehicles mainly include the following: 1. Query on the Motor Vehicle Environmental Protection Website; 2. Inquiry at the Vehicle Management Office; 3. Check the vehicle's environmental protection label; 4. Review the vehicle's factory certificate. Additional information: 1. China 5 and China 6 refer to standards established to implement the Environmental Protection Law of the People's Republic of China and the Air Pollution Prevention and Control Law of the People's Republic of China, aiming to prevent pollution from the exhaust of compression-ignition and gas-fueled ignition engine vehicles, protect the ecological environment, and safeguard human health. 2. The differences between China 5 and China 6 include: (1) Different implementation times: China 5 standard was implemented in December 2017; China 6 standard was implemented in December 2014. (2) Different sulfur content limits: China 5 standard stipulates no more than 10mg per kilogram; China 6 standard stipulates no more than 50mg per kilogram.
109
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.