What brand of tires does the Haval H6 use?

How to Remove the Steering Wheel of a Chery A3?

Method to remove the steering wheel of a Chery A3: 1. Disconnect the battery; 2. Turn the steering wheel approximately 90 degrees; 3. Insert a flat-head screwdriver into the hole behind the steering wheel; 4. Insert the tip of the screwdriver between the retaining clip and the airbag hook, causing the airbag side to automatically pop slightly towards the seat; 5. Turn the steering wheel 180 degrees and continue to pry open the retaining clip; 6. Remove the airbag, disconnect the yellow safety clip behind the airbag, and take out the airbag; 7. Unplug the airbag coupling coil connector located above inside the steering wheel, and use an M12 spline to loosen the central fixing bolt of the steering wheel counterclockwise; 8. Remove the steering wheel.

15

1

Share

How to Use the Mechanical Key of Sagitar?

The method to use the mechanical key of Sagitar is as follows: 1. Insert the key into the ignition and turn it to the 'on' position; 2. Place the gear lever in the neutral position; 3. Press the clutch pedal all the way down and turn the key to the 'start' position. Taking the 2021 manual Fashion Smart Connection Edition Sagitar as an example, its body dimensions are: length 4753mm, width 1800mm, height 1462mm, with a wheelbase of 2731mm, a fuel tank capacity of 50 liters, and a minimum ground clearance of 2731mm. The 2021 manual Fashion Smart Connection Edition Sagitar features a MacPherson independent front suspension and a multi-link independent rear suspension. It is equipped with a 1.2T turbocharged engine, delivering a maximum horsepower of 116PS, a maximum power of 85kW, and a maximum torque of 175Nm, paired with a 5-speed manual transmission.

5

2

Share

What are the dimensions for parallel parking a car?

The standard dimensions for parallel parking are as follows: The parking space length is 5.25 meters and width is 2.3 meters. The total road length is 15.9 meters, with single side length of 6.8 meters and width of 5.8 meters. Parallel parking evaluation criteria: Failing to follow specified route/sequence results in failure; Vehicle crossing lines results in failure; Incomplete parking results in failure; Stopping midway results in failure; Exceeding 4 minutes results in failure. Parallel parking rhyme: Parking in/out isn't hard, fasten belt, shift gear, left signal flashes. Press clutch, release handbrake, slowly lift clutch to start gently. Align body with right line, left mirror seam follows right line. Stop when front line reaches shoulder, shift to reverse, release clutch. When left mirror covers corner line, turn wheel fully right. Watch left mirror for garage line, at 30° angle turn back one round, when car parallels line, straighten wheel two full turns. When left mirror covers front corner, press clutch and brake. Shift to first gear to exit, turn fully left when hood touches line. Stop when hood covers line, keep wheel position to reverse. Watch right mirror for garage line, at 30° angle turn back one round, when car parallels line, straighten wheel two full turns, when left mirror covers front corner, press clutch and brake. Shift to first gear to exit, turn fully right when hood touches line. Stop when hood covers line, skillfully adjust body position. The new parking space has no poles, only ground markings. The length is much shorter, just enough for one car. The process is simpler: reverse in from right, drive out to left, reverse back in, then drive out to starting point - eliminating the current test's garage transfer step.

9

3

Share

Which part of the vehicle should the jack be placed under?

The jack is located on the left side of the car trunk. There are two common types of car jacks: one is the rack jack, and the other is the screw jack. How to use a rack jack: Open the jack to form a diamond shape, with the top being the support part and the bottom being the base. Place the base downward and the support part under the car's chassis. Insert the jack into the gap between the chassis and the ground, use the wheel hub bolt wrench as a crank, and simply turn it. How to use a screw jack: Place the base directly on the ground with the support part under the vehicle's chassis, insert the wheel hub bolt wrench into a small hole to act as a crank, and then turn it. When using the jack, you can place the spare tire under the chassis to prevent the vehicle from suddenly falling, providing an additional support.

17

2

Share

What to Pay Attention to When Taking Delivery of a New Car?

When taking delivery of a new car, pay attention to the following: 1. Ensure all accompanying documents are complete, including the purchase invoice, vehicle certification, vehicle conformity certificate, motor vehicle registration certificate, and warranty certificate; 2. Inspect the vehicle's exterior to check if the paint is uniform and free from scratches or wear. The production date of the car's windows can be determined by checking the labels on the glass; 3. Check the electrical equipment. After starting the engine, observe its condition and test the functions of other electrical equipment, including lights, wipers, air conditioning, multimedia system, and windows. It is important to note that the accompanying documents of a new car are crucial, as some are necessary for later registration. Therefore, they must be complete; otherwise, it may affect the new car registration.

18

0

Share

Should You Wash the Car Before Applying Window Tint?

It is necessary to wash the car before applying window tint. The method for applying the tint is as follows: 1. Use a specialized glass cleaner to remove dust and any dirt adhering to the glass. 2. Cover areas such as the hood and doors that might get dirty during the tinting process. 3. Measure the dimensions of the glass to be tinted and cut the film accordingly. 4. Apply the cut film to the glass, which has been sprayed with water, and trim it to fit the shape of the glass. 5. Use a heat gun to warm the film while pressing it with a plastic squeegee until it fully conforms to the curvature of the glass. 6. Clean the inside of the glass thoroughly. 7. Spray installation fluid on both the film and the inner surface of the glass before applying the film. 8. Spray installation fluid again on the surface of the film and use a squeegee to smooth it from the center to the edges, working from top to bottom and then to the bottom edge. 9. Finally, clean both the inner and outer surfaces of all window glass.

1

4

Share

What brand of tires does the Haval H6 use?

How to Remove the Steering Wheel of a Chery A3?

How to Use the Mechanical Key of Sagitar?

What are the dimensions for parallel parking a car?

Which part of the vehicle should the jack be placed under?

What to Pay Attention to When Taking Delivery of a New Car?

Should You Wash the Car Before Applying Window Tint?

How to use the cigarette lighter in Audi A6L?

Is the first maintenance of a new car free?

Where is the headlight height adjustment button for the 10th-generation Accord?

What should be noted when using a new car?