What are the steps to reset the maintenance light on the new Highlander?

[StCourtney]

Steps to reset the maintenance light on the new Highlander: 1. With the engine off, press and hold the short-distance counter reset button below the tachometer; 2. Turn the ignition switch to the ON position, release the short-distance counter reset button, and the SERVICE indicator will appear on the dashboard; 3. Pull out the minute button of the clock and turn it to the right; the mileage will appear on the display; 4. Turn off the engine at this point, and the vehicle computer will prompt a reset; 5. Turn the ignition switch to the ON position, and the SERVICE indicator will disappear, completing the entire maintenance light reset process. The new Highlander is equipped with a 2.0T turbocharged engine model, replacing the original 2.7L engine, and uses 95-octane or higher gasoline.

[StHenry]

I just researched how to turn off the maintenance light on the new Highlander! After getting in the car, don't press the brake pedal—just press the start button twice to power up the dashboard. At this point, you'll see the maintenance reminder pop up in the center of the display. Use the small buttons on the right side of the steering wheel (the directional pad for the trip computer) to navigate left or right a few times until you find the maintenance reset option in the settings menu. Here's the key step: Press and hold the √ confirmation button on the steering wheel for 3 seconds without releasing it. Wait until the progress bar on the dashboard completes or the warning light turns off. After finishing, it's best to turn off the ignition and restart to check if it worked. This operation is like turning off a phone alarm—don't overcomplicate it. The crucial part is holding the menu button long enough. Beginners might need to try it twice to get the hang of it.

[Gideon]

I often reset the maintenance light on the new Highlander. The most reliable method is to park the car, turn off the engine, and then press the small button next to the instrument cluster—the one used to adjust time and toggle the odometer. At this point, turn the key to the "ON" position without starting the engine, keep holding the button for about 5 seconds, and release it immediately when the English maintenance mode menu pops up on the instrument panel. Then, follow the prompts to select "reset maintenance indicator" and confirm. The whole process takes about 30 seconds. Actually, the manufacturer designed this feature to prevent you from forgetting the last maintenance time. I usually check the oil dipstick level while doing this, since resetting the maintenance reminder should align with the actual vehicle condition. Remember to perform the reset promptly after maintenance, otherwise the light popping up every day can be quite annoying.

[VonPenelope]

Resetting the maintenance light is actually super easy: After powering on without starting the engine, locate the two small buttons near the left leg of the steering wheel. Navigate to the settings menu, find the vehicle maintenance option, select reset, and hold the confirm button for about 5 seconds. Key note: The infotainment system may vary slightly for different model years, but this method works flawlessly for 2023 models. The principle is simply clearing the mileage counter recorded in the system—similar to resetting an alarm clock. Avoid unreliable tricks like disconnecting the battery, as they may cause fuel consumption data loss. If unsure, check page 72 of the manual in the glove compartment for detailed illustrated steps.

[Reed]

The method the guy at the 4S shop taught me last time was super practical: Sit in the driver's seat, insert the key and turn it to the ON position without starting the engine. Use the round button on the right side of the steering wheel to navigate to the vehicle information page, scroll down to find the maintenance settings. Select 'Reset Reminder' and hold the OK button, then watch the dashboard blink a few times—done. The whole process takes just 1 minute, much easier than driving to the repair shop. This light is just reminding you to change the oil. I recommend doing this right after maintenance, otherwise, it keeps lighting up on the highway and distracts you. Make it a habit to clear it when you check tire pressure yourself—then you won’t forget.

[SophieAnn]

As a veteran driver who has owned three generations of Highlanders, I must remind you to verify the mileage after resetting the maintenance light. The steps are simple—power on the vehicle, press and hold the OK button on the steering wheel for 3 seconds to enter settings, then locate and confirm the maintenance reset in the menu. However, many people overlook the key point: pay close attention to the text prompts that appear on the dashboard to avoid incorrect operations. Accidentally deleting tire pressure data can cause unnecessary trouble. New owners can search for video tutorials of their specific model on TikTok for a more visual guide. This design is essentially a safety reminder—don’t rely on resetting as a substitute for actual maintenance. You still need to change the oil on time.