···
Log in / Register

What are the precautions for changing Fit tires from 185 to 195?

6Answers
DelMiguel
07/29/2025, 02:11:58 AM

Precautions for changing Fit tires from 185 to 195: 1. Note that the diameter of the tire will increase after replacement, so the ground clearance of the car will also increase, leading to higher fuel consumption and slower acceleration, but the car can run faster. 2. For small-displacement engines, it may also reduce the vehicle's acceleration capability. 3. 195 tires are more expensive than 185 tires, increasing the cost of tire replacement. 4. Changing the tire size may cause the vehicle to fail the annual inspection. Precautions for tire use: 1. Pay attention to tire pressure, as it is crucial for tire longevity—both too high and too low pressure will shorten the tire's lifespan. 2. If the pressure is too low, the tire body deformation increases, cracks may appear on the tire side, and flexing motion occurs, leading to excessive heat generation, which accelerates rubber aging, fatigue of the cord layer, and breakage of the cords.

Was this review help?
116
Share
SamanthaRose
08/12/2025, 05:18:38 PM

When upgrading the Fit's tires from 185 to 195, I must first ensure the wheel rim width is compatible. Otherwise, the new tires may rub against the wheel arches or interfere with steering, creating safety hazards. Additionally, wider tires will cause speedometer inaccuracies due to the changed diameter, potentially leading to speeding tickets or extra drivetrain wear. I also recommend checking the suspension system, as 195 tires may be stiffer or softer, affecting ride comfort—especially making bumps over speed bumps more noticeable. Finally, ensure tire pressure is adjusted to the manufacturer's recommended value; don't overinflate just for extra grip. After the change, monitor fuel consumption regularly for any upward trend. This prevents minor modifications from causing major issues and maintains smooth driving.

Was this review help?
11
Share
Expand All
MilesMarie
10/03/2025, 10:22:45 PM

When I drove the Fit before, I also replaced the 185 tires with 195 ones. The grip improved noticeably, making driving in the rain much more stable. However, fuel consumption did increase a bit, especially on long trips where I used to save 50 cents but now spend around 80 cents more. Don’t overlook the wheel size—too narrow rims with wider tires can cause tire deformation, accelerate wear, and even lead to blowouts. Also, remember to adjust the tire pressure to a balanced point; too high will make the ride bumpy, while too low will wear the tires faster. Drive slowly for the first few days after the modification to ensure the tires don’t rub against the body when not turning. Although this is a minor modification, it can improve handling and make city driving safer. Make sure to choose matching brands and avoid buying cheap second-hand tires.

Was this review help?
17
Share
Expand All
DeJasmine
11/16/2025, 10:58:08 PM

Be cautious about the cost when switching to wider tires. Upgrading from 185 to 195 means purchasing more expensive new tires, with an average increase of around 80-100 yuan per tire, totaling over a thousand yuan including installation fees. Increased fuel consumption is common after the change, adding dozens of yuan to monthly commuting costs; wear resistance may also decrease, and if the rims don't match, tire edges can wear out quickly, making a year's worth of new tires pointless. It's advisable to compare the size charts of old and new tires to ensure they don't exceed the manufacturer's allowed range—otherwise, the effort might not be worth it. Also, check your insurance policy, as modifications can sometimes complicate claims, turning small savings into big troubles.

Was this review help?
12
Share
Expand All
SanIsabela
01/07/2026, 12:36:42 AM

Pay attention to regulations and safety! In some places, privately changing the tire width is illegal, and you may get a ticket during road inspections; after switching to 195 tires, the speedometer becomes inaccurate, showing lower readings, which can easily lead to speeding and may even trigger brake failure risks. The rims must be compatible—if you change the tires without replacing the rims, a width that's too small can cause tire deformation and uneven contact with the road, increasing body roll during high-speed cornering. During maintenance, check tire pressure and outer tire wear frequently to ensure uniformity; safety comes first—consult a repair shop before making changes to avoid issues, and don’t sacrifice driving safety for aesthetics.

Was this review help?
1
Share
Expand All
VanClaire
04/03/2026, 11:37:58 PM

I discussed this with a friend who switched from 185 to 195 tires on his Fit. Initially, it felt more stable with no drifting during turns, but after a week, he noticed a clicking noise. Upon inspection, he found the wheel rim was slightly too narrow, causing the tire edge to rub against the inner liner, creating noise. It was all for nothing as he had to remove and reinstall them. My advice is to measure the wheel rim compatibility before changing tires—even a 1mm difference won't work. After the change, test drive on low-speed sections to check for interference with the suspension or tire scraping when turning the steering wheel to full lock. Regular maintenance is crucial—check tire pressure monthly to ensure it's within the standard range. This minor modification can improve comfort, but don't overlook potential issues.

Was this review help?
20
Share
Expand All
More Q&A

What type of engine oil is best for the RAV4?

Toyota's engine manufacturer recommends using engine oil with a viscosity of 0w-20 or 5w-30. For new vehicles, it is advisable to use 0w-20 viscosity oil as it can reduce engine resistance and fuel consumption. 1. Lubrication and friction reduction: Forms an oil film on the surfaces of two sliding components to prevent friction during operation, ensuring smooth movement. 2. Cleaning and dispersion: High-quality oil can flush away surface contaminants on components through oil flow, adsorb tiny metal fragments inside the engine, and then rely on the piston oil ring to scrape them into the oil pan. 3. Cooling: The engine generates high temperatures during operation. When the oil reaches the operating parts, it absorbs heat and carries it away, aiding in component cooling. 4. Sealing and leakage prevention: Forms a sealing ring between the piston ring and piston via an oil film to prevent combustion exhaust gases from entering the crankcase. 5. Rust and corrosion prevention: High-quality oil adheres to component surfaces, preventing contact with air, acidic substances, and harmful gases, protecting the engine from corrosion by atmosphere and water.
116
Share

What kind of engine oil should be used for Toyota Reiz V6?

Toyota Reiz V6 recommends using fully synthetic engine oil. The benefits of using fully synthetic engine oil: 1. Low evaporation loss: Synthetic oil is generally a pure compound with a narrow boiling point range, and its evaporation loss is much lower than that of mineral oil, which can reduce fuel consumption, reduce exhaust emissions, and extend the service life of the catalytic converter. In addition, compared with traditional mineral oil-type engine oil, synthetic engine oil also has excellent chemical stability, good radiation resistance, high oil film strength, and less foam. Therefore, high-end cars generally choose synthetic engine oil. 2. Strong high-temperature oxidation resistance: The thermal oxidation stability of synthetic oil is much better than that of mineral oil-type engine oil, which means the tendency to produce acid and sludge due to oxidation is small. Under various harsh operating conditions, it can provide appropriate lubrication and effective protection for the engine, thus having a longer service life and ensuring the performance stability of the engine oil during long-term use. In the same working environment, synthetic oil has a much longer service life than mineral oil, so although the cost is higher, after comparing the number of oil changes, it is not much higher than mineral oil.
113
Share

What to Do If You Keep Hitting the Corner in the Right-Angle Turn of Subject Two?

The solutions for frequently hitting the corner in the right-angle turn of Subject Two are as follows: 1. Turn the steering wheel fully to the left: When the bottom of the black vertical rod on the left window falls on the horizontal extension line of the corner, turn the steering wheel fully to the left. Observe the rearview mirror carefully. When the car body is parallel to the sideline, straighten the steering wheel and drive out of the test area at a steady speed. 2. Turn left: Keep the car close to the right side, similar to aligning for parallel parking, maintaining a distance of about 30cm between the car body and the right sideline while driving straight. Then, watch the car hood. As soon as the car hood aligns with the sideline, immediately turn the steering wheel fully to the left, and straighten the direction as soon as the car hood is aligned.
103
Share

Why is the Mercedes-Benz rearview mirror not automatically retracting?

It may be due to the battery being disconnected, out of power, or not properly set. Here are the relevant explanations: 1. Automatic folding function: Mercedes-Benz comes with a one-touch automatic folding rearview mirror function. The function button is located on the front driver's door, parallel to the rearview mirror. The four directional keys represent the four angle adjustments of the rearview mirror, the RL key represents the left and right rearview mirrors, and the middle round button is the folding switch. When the rearview mirror is extended, press and hold the middle round button for more than 2 seconds to fold it. When folded, press and hold it for more than 2 seconds to restore it to the memorized position and extend the rearview mirror. 2. Gear mechanism damage: If you feel the vibration of the motor working but the rearview mirror does not move, it proves that the opening and closing gear mechanism is damaged. If you do not feel the vibration of the motor working and there is still no response after tapping it a few times, it indicates a motor failure or wiring issue. Wiring problems are usually caused by switch damage or a blown fuse.
111
Share

What are the effects of using low-quality fuel on trucks?

The effects of using low-quality fuel on trucks are as follows: 1. Damage to the diesel filter: Low-quality fuel contains a large amount of impurities, and long-term use will overload the diesel filter. Over time, the impurities will coat the filter, eventually leading to clogging of the filter and fuel injectors, causing poor fuel supply and poor vehicle acceleration. In severe cases, high-speed vehicles may stall due to fuel cut-off, potentially leading to more serious consequences. 2. Engine idle vibration: Due to poor fuel quality, the fuel entering the cylinders cannot burn completely, or more knocking phenomena may occur during combustion. This results in engine vibration at idle, poor acceleration, and reduced power. 3. Clogged fuel injectors: Poor fuel quality can cause clogging of the fuel injectors, which not only leads to poor engine performance but may also cause the engine to stall in severe cases. If the vehicle is traveling at high speed, sudden stalling can lead to major accidents. 4. Damage to the urea injector: The complex post-treatment system of China VI is an important module that differs from China V. Low-quality fuel contains too many impurities, and the exhaust gases produced after combustion contain a large amount of sulfur compounds that can corrode the urea injector. Once the post-treatment system is damaged, frequent malfunctions may occur.
105
Share

What to Do with Renault Koleos Parts After Discontinuation?

The car manufacturer should ensure the supply of consumable parts within five years, and auto parts manufacturers will continue to produce parts, so there is basically no need to worry about parts availability. Parts refer to the components or assemblies used in assembling machinery; they also include parts or assemblies replaced after damage. Parts can be divided into two categories: standard parts and optional parts. The lifespan of a car is very long, so both automakers and the government have taken this into consideration. Here is additional information: 1. Three Guarantees Policy: The General Administration of Quality Supervision, Inspection and Quarantine issued the "Automobile Three Guarantees Policy" in 2005, requiring that automobile after-sales services must meet users' needs for 10 years after the discontinuation of the entire vehicle production. 2. Discontinuation Analysis: Automobile discontinuation can be discussed from two aspects: one is the discontinuation of an entire series, and the other is the discontinuation of a specific model within a series. Car models are frequently updated and replaced. For example, after a recent update, a low-end model from five years ago may be discontinued, but the series itself will continue to be produced.
109
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.