What are the maintenance intervals for the Kicks?

Do new energy electric vehicles have a vehicle license?

New energy electric vehicles have a vehicle license. Road requirements: Low-speed electric vehicles are subject to a registration system in accordance with motor vehicle management and can only be driven on the road after being registered by the traffic management department of the public security organ. According to the national "Regulations on the Application and Use of Motor Vehicle Drivers", drivers of low-speed electric vehicles should obtain a C3 (including C3) or higher driver's license. Electric vehicles (BEV): Refers to vehicles that use on-board power as the power source, use motors to drive the wheels, and meet all the requirements of road traffic and safety regulations. Due to their relatively smaller environmental impact compared to traditional vehicles, their prospects are widely optimistic, but the current technology is not yet mature. Working principle: battery - current - power regulator - motor - power transmission system - driving the vehicle (Road).

120

Share

How to Fix P0366 Trouble Code?

P0366 trouble code can be resolved by replacing the camshaft. This code indicates a fault in the B (exhaust/right/rear) camshaft (CMP). The reasons for camshaft failure are as follows: 1. The camshaft is located at the end of the engine lubrication system, so the lubrication condition is not ideal. If the oil pump fails to provide sufficient oil pressure due to prolonged use, or the lubrication channels are blocked preventing oil from reaching the camshaft, or the bearing cap fastening bolts are overtightened preventing oil from entering the camshaft clearance, all these can cause abnormal wear of the camshaft. 2. Abnormal wear of the camshaft can increase the clearance between the camshaft and the bearing seat, causing axial displacement during camshaft movement, which results in abnormal noise. Abnormal wear can also increase the clearance between the cam lobe and the hydraulic lifter, causing impact and noise when they engage. 3. The camshaft may sometimes suffer severe failures such as fractures. Common causes include shattered or severely worn hydraulic lifters, severe lubrication failure, poor-quality camshaft, or a broken camshaft timing gear. 4. Incorrect disassembly or assembly of the camshaft during engine repair can lead to camshaft failure. For example, forcibly striking the camshaft bearing cap with a hammer or prying it with a screwdriver during removal; installing the bearing cap in the wrong position causing mismatch with the bearing seat; overtightening the bearing cap fastening bolts. When installing the bearing cap, pay attention to the directional arrows and position numbers marked on the cap surface, and strictly follow the specified torque using a torque wrench to tighten the bearing cap bolts.

112

Share

How to operate one-touch power window?

One-touch power window can be operated through the interior window control buttons. There are corresponding control buttons below each window: pressing the button to the bottom position activates one-touch down, lifting the button to the top position activates one-touch up, lifting the button one position enables manual window up, and pressing the button one position enables manual window down. Here is relevant information about one-touch power window: 1. One-touch power window refers to when the vehicle's computer receives a window-up signal (usually by immediately releasing the window switch after lifting) shorter than the preset time, it will send continuous window-up commands to the window motor until fully closed. 2. If the window switch is lifted or pressed again during window-up operation, the action will stop. 3. If the window switch is continuously held up longer than the one-touch preset time, the window will continue rising, but will stop immediately when the switch is released. 4. One-touch power window must be used with anti-pinch function, otherwise it may easily cause injuries due to the motor's strong closing force. This is why many vehicle models have one-touch down but not one-touch up function. 5. With anti-pinch function, there's additional motor current monitoring and control circuitry. When motor current increases beyond certain parameters (indicating foreign object interference causing motor overload), the motor will stop.

117

Share

Does crossing the stop line when the red light turns on count as running a red light?

If the vehicle stops, it does not count as running a red light. However, if it continues to drive past, it does count as running a red light. If the vehicle stops at the crosswalk without proceeding further, it is not considered running a red light but rather as stopping beyond the line. According to Article 4, Item 5 of the Scoring Standards for Road Traffic Safety Violations: Failing to drive or stop as required at intersections will result in a 2-point deduction. Running a red light refers to the act where the vehicle, while still behind the stop line, proceeds forward despite the traffic signal being red, and both the front and rear wheels cross the stop line. For electronic enforcement of red-light running, three photos are required: The vehicle is behind the stop line while the traffic signal is red. The vehicle continues to move forward under the red light, with both front and rear wheels crossing the stop line. The vehicle proceeds into the intersection: indicating whether the vehicle forcibly passed through during the red light. On October 8, 2012, the Ministry of Public Security revised and issued the Regulations on the Application and Use of Motor Vehicle Driving Licenses, increasing the penalty for violations such as running a red light from 3 points to 6 points. Running a yellow light will be treated as running a red light, also resulting in a 6-point deduction and a fine. Failing to yield to a 120 emergency vehicle will result in a 3-point deduction. Intentionally following a 120 emergency vehicle through a red light will result in a 6-point deduction and a fine. Running a red light is not considered illegal under the following circumstances: Yielding to special vehicles: Yielding to ambulances, fire trucks, or other special vehicles. If caught by surveillance cameras while yielding, manual review will not record the act as running a red light. Even if recorded, you can apply for reconsideration at the traffic police department. Extreme weather: When visibility is so low that even electronic police cannot clearly see the traffic lights. The photos of the violation may be blurry, and if you mistakenly run a red light, the traffic police will not impose penalties. Emergency situations: After delivering a critically ill patient, you can present proof from the hospital or the rescued person to the traffic police for verification. If confirmed, the violation record can be cleared. If possible, it is best to call an ambulance to avoid accidents caused by running a red light. Traffic police direction: During peak hours, traffic police may temporarily direct traffic at major intersections. Drivers must follow the gestures of the traffic police.

113

Share

What are the common methods for detecting pavement rutting?

Common methods for detecting pavement rutting include the rutting method. Pavement measurement method: Select the cross-section to be tested for rutting, place the reference ruler on the test cross-section, with its direction perpendicular to the road centerline. Requirements for the test section: Determine the test section, which should be free of standing water, ice, snow, and contamination. Adjust the tire pressure of all test equipment to the standard pressure required by the equipment, and check whether the vehicle and test equipment are functioning properly. ③ Check the weather forecast; testing should not be conducted when the wind speed exceeds level 6. When using a laser rutting instrument to measure the rut depth of the pavement, adjustments or avoidance should be made if sunlight affects the test results.

116

Share

What is the fuel consumption of the 7th generation Elantra 1.5?

The 7th generation Elantra 1.5L model has a combined fuel consumption of 4.9 liters per 100 kilometers under comprehensive driving conditions. This car excels in the following aspects: 1. Exterior design. The overall body appears gentle and elegant, but the redesigned front face exudes aggressiveness. Two prominent ridges on the engine hood extend forward to a small yet protruding grille, creating a strong sense of forward motion. The redesigned wedge-shaped headlights are more sporty than the peanut-shaped ones found on the Sonata. 2. Interior design. The Elantra's interior features clean lines, with a beige color scheme that gives a fresh feel. Matte metallic trim panels on the center console and door armrests add a touch of modernity. The plastic components on the dashboard are of decent quality, avoiding a particularly cheap impression. The Elantra measures 4495mm in length, 1720mm in width, and 1425mm in height, with a wheelbase of 2610mm, which is quite outstanding in its class. The interior space is also top-tier among its peers, with notable width and ample legroom and headroom in both the front and rear seats. 3. Chassis. The Elantra employs a front MacPherson strut and rear multi-link suspension system, equipped with gas-filled shock absorbers tuned for softness, delivering first-class comfort. On regular roads, road vibrations are effectively filtered out, and cabin noise reduction is well-executed, making the overall ride comfort comparable to that of a higher-class mid-size sedan.

101

Share