···
Log in / Register

Is the fuel consumption of the old Mazda 6 high?

6Answers
Alexandra
07/29/2025, 09:40:25 PM

The comprehensive fuel consumption of the old Mazda 6 is about 10 liters per 100 kilometers, which is relatively high. More information about the Mazda 6 is as follows: 1. The Mazda 6's exterior design features an oval front face inspired by sports cars, combined with a wide and low chassis, showcasing Mazda's strong dynamic feel. 2. The Mazda 6 is equipped with 2.0-liter and 2.3-liter inline four-cylinder engines. Its 2.3-liter four-cylinder engine utilizes Sequential Valve Timing (S-VT) and Variable Valve Timing (VVT) technologies, which can significantly improve engine power, output more torque, and provide greater performance.

Was this review help?
108
Share
StKevin
08/15/2025, 03:27:26 AM

The fuel consumption of the old Mazda6 really depends on the specific situation. My 10-year-old 2.0L automatic version consumes around 10-11 liters per 100km in city driving, and it can drop to just over 7 liters on the highway. These cars are all quite old now, so the engine condition is particularly crucial. Worn spark plugs or a faulty oxygen sensor can cause fuel consumption to skyrocket. In summer, with the AC on and stuck in traffic, it's not uncommon to see consumption hit 13 liters per 100km. However, among Japanese cars of the same era, its fuel consumption isn't particularly low, mainly because the 5AT transmission is considered outdated by today's standards. I recommend checking tire pressure and the air filter—these are the simplest factors but have a significant impact.

Was this review help?
19
Share
Expand All
McKing
10/20/2025, 04:29:36 AM

When I drove my old Mazda 6 for ride-hailing, I specifically tested the fuel consumption: the 2.3L automatic transmission model consumes at least 13L/100km in city driving, and can be reduced to 10.5L/100km with gentle driving. The most fuel-consuming part is frequent acceleration, as this car has weak low-end torque and often requires deep throttle input. Last time, while helping a fellow car owner diagnose high fuel consumption, I found the carbon canister purge valve was faulty, causing fuel tank vapors to directly enter the engine and waste fuel unnecessarily. Additionally, carrying too much clutter in the trunk can increase consumption by 0.5L/100km - with older cars, you really need to be meticulous about these details.

Was this review help?
19
Share
Expand All
DanielaMarie
12/03/2025, 09:13:14 PM

The fuel consumption of the old Mazda6 largely depends on the vehicle's condition. I've refurbished over twenty of them. A normal 2.0MT should consume around 9 liters per 100km; anything over 12 indicates a problem. Common issues include: a faulty rear oxygen sensor causing excessive fuel injection, leaking ignition coils leading to incomplete combustion, and a significant drop in transmission efficiency if the gearbox oil hasn't been changed in eight years. Last week, an owner reported high fuel consumption, which turned out to be due to switching to 235 wide tires—the original 205 width is sufficient.

Was this review help?
3
Share
Expand All
IsabellaMarie
01/23/2026, 10:36:55 PM

After seven years of driving a 2.0L manual transmission, here's my summary: Gentle driving at 60km/h yields the best fuel economy at 6.8L/100km, but daily commuting with frequent traffic lights usually results in around 9.5L/100km. Winter consumption is about 0.5L higher than summer. Using 5W40 engine oil increases consumption by 0.3L compared to 0W20. I recommend regular throttle body cleaning for older vehicles - carbon buildup causes unstable idle and higher fuel consumption. Modified exhaust systems should be noted - insufficient backpressure reduces low-end torque and increases fuel consumption.

Was this review help?
8
Share
Expand All
DiAngelina
04/19/2026, 04:44:59 AM

When I first took over my dad's 2008 Mazda 6, the fuel consumption was a shocking 14L. After replacing the iridium spark plugs and cleaning the fuel injectors, it immediately dropped to 10L. A special reminder: regularly change the fuel filter—mine was clogged, causing the fuel pump to work overtime. For older cars, it's recommended to use fuel system cleaner to remove carbon deposits; now it's basically maintaining 9.2L. The fuel consumption of this car varies depending on how it's driven—shifting at 3000 RPM versus 2000 RPM can make a 2L difference. Also, an aging AC compressor is a hidden fuel consumption killer.

Was this review help?
19
Share
Expand All
More Q&A

How to remove ISOFIX?

Method for removing an ISOFIX rigid interface car seat: 1. First, adjust the headrest of the car seat to the highest position. 2. Press the shoulder strap adjuster to extend the shoulder straps to their maximum length. 3. Open the buckle and separate the shoulder straps to the left and right. 4. Fasten the five-point buckle and adjust the shoulder straps to their shortest length. 5. Push the seat inward, press the red buttons on the ISOFIX connectors simultaneously with both hands, and pull backward forcefully. A click sound indicates that the ISOFIX connectors have been successfully removed. Introduction to ISOFIX: 1. ISOFIX is a new standard for installing child car seats in vehicles. 2. Function of ISOFIX: It makes the installation of child car seats quick and easy, and the rigid connection enhances safety.
113
Share

What is the method for cleaning a car radiator?

It is necessary to clean the car radiator cooling system once a year to maximize the lifespan of the car radiator. The method for cleaning a car radiator is as follows: 1. Ensure the engine is cool and turned off, then remove the radiator cap, making sure the engine is not hot. 2. Open the drain plug at the bottom of the radiator to allow the coolant to flow into a bucket. The coolant should be disposed of properly to avoid environmental harm. 3. Close the drain plug and fill the radiator with water. 4. Start the engine and turn on the heater control system (this will open the heater control valve), add the cooling system cleaner, and let the engine idle for 30 minutes (or follow the instructions on the cleaner bottle). 5. Turn off the engine and let it cool for 5 minutes, then drain the liquid from the radiator. 6. Close the drain plug, fill the radiator with water, and let the engine idle for 5 minutes. Then refill with a 50/50 mixture of water and ethylene glycol antifreeze/coolant.
108
Share

Why is the antifreeze level low?

Antifreeze is designed to prevent the coolant from freezing during cold winter parking, which could otherwise crack the radiator and damage the engine block. The reasons for low antifreeze levels are as follows: 1. Increased water temperature leading to natural evaporation. Antifreeze serves a cooling function for the car engine, which often operates at high temperatures. Since the antifreeze is in constant contact with the engine, some consumption is normal. 2. Corrosion and deterioration of the cylinder head gasket, resulting in severe antifreeze loss (especially if water is used as a substitute in summer, accelerating corrosion). Replacing the cylinder head gasket will resolve this issue. 3. Malfunctioning water pump or thermostat: This can cause the water temperature in the circulation system to rise excessively, leading to increased pressure inside the radiator and cooling system, which forces antifreeze to overflow from the reservoir. Prompt repair or replacement of the water pump or thermostat is necessary to restore normal function.
117
Share

What are the reasons for a car's exhaust emissions failing to meet standards?

There are four main reasons why a car's exhaust emissions may fail to meet standards: 1. Aging of car components: During long-term use, many parts of a car may age, leading to a noticeable decline in performance. For vehicles used over an extended period, it can be difficult to meet emission standards, possibly due to the level of production technology causing excessive emissions. 2. Poor fuel quality: When refueling, if the fuel quality is not guaranteed, the high impurity content in low-quality fuel can easily lead to excessive emissions. This may result in the car failing the annual inspection, especially for imported cars, which have stricter fuel requirements. 3. Catalytic converter failure: After prolonged use, the catalytic converter may malfunction due to carbon buildup in the car. Therefore, regular maintenance should include checking the catalytic converter to avoid emission-related failures during the annual inspection. 4. Design or production defects causing the vehicle to exceed standard atmospheric pollutant emissions.
111
Share

Which region does a license plate starting with 'Ji' belong to?

Ji is the license plate prefix for Shijiazhuang City, Hebei Province. Ji is the abbreviation for Hebei Province, hence all vehicle license plates in Hebei Province start with 'Ji', with license plate codes ranging from JiA to JiT. Hebei Province is a provincial-level administrative region of the People's Republic of China, with Shijiazhuang as its capital. Information regarding vehicle license plates is as follows: 1. License plates, commonly known as vehicle plates, refer to the plates hung on the front and rear of a vehicle. They are typically made of aluminum, iron, plastic, or paper, and display the vehicle's registration number, registration region, or other relevant information. 2. License plates serve as a numbering and information registration system for vehicles. Their primary function is to identify the region to which a vehicle belongs and to trace the vehicle's owner and registration details based on the plate. 3. License plate numbers can be customized, with the exception of the first two characters, which must comply with national regulations; the remaining characters can be freely chosen.
110
Share

Which city does the license plate starting with Gui K belong to?

Gui K is the license plate prefix for Yulin City in Guangxi. The license plate prefixes for other cities in Guangxi are as follows: Guangxi Zhuang Autonomous Region (Gui) Gui A Nanning, Gui B Liuzhou, Gui C Guilin, Gui D Wuzhou, Gui E Beihai, Gui F Chongzuo, Gui G Laibin, Gui H counties under Guilin City (excluding Yangshuo County, formerly the Guilin Prefecture), Gui J Hezhou, Gui K Yulin, Gui L Baise, Gui M Hechi, Gui N Qinzhou, Gui P Fangchenggang, Gui R Guigang. Relevant information about license plates is as follows: 1. License plates, commonly known as vehicle plates, refer to the plates hung on the front and rear of vehicles. They are usually made of aluminum, sheet iron, plastic, or paper, engraved with the vehicle's registration number, registration region, or other relevant information. 2. License plates serve as a numbering and information registration system for vehicles. Their primary function is to identify the region to which the vehicle belongs and to enable the tracing of the vehicle's owner and registration details based on the license plate.
106
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.