Is Repainting the Hood Durable?

1 Answers
JosiahAnn
07/29/25 10:43pm
Not durable. After the hood is repainted, prolonged use can lead to paint cracking, color fading, and eventual paint peeling. The reason is that the engine generates high temperatures during operation, which can cause changes in the hood's paint surface, thereby affecting its durability. Additional Information: Repainting the hood does have an impact. Firstly, there may be some color discrepancy. During the later stages of vehicle use, the hood may experience color fading. In severe cases, paint peeling may occur, which also affects the resale value of the vehicle. This is because the vehicle's paint has been resprayed. While driving, it is essential to pay attention to the vehicle's safety.
Was this review help?
7
0
Share
More Forum Discussions

What is the fuel consumption of the BJ40 off-road vehicle?

The BJ40 off-road vehicle has 15 models currently on sale. Among them, the Beijing BJ40-2022-2.0T-Automatic Four-Wheel Drive Official Edition, Champion Edition, 2020-2.0T-Automatic Four-Wheel Drive City Hunter Edition Supreme, and Xia Ke Edition, equipped with a 224 horsepower engine, have an NEDC fuel consumption of 9.9L per 100km. The 2020-2.0T-Automatic Four-Wheel Drive Tribute 2020 Edition Xia Ke, Supreme, Automatic Two-Wheel Drive City Hunter Edition Pioneer, and Xia Ke Edition, equipped with a 224 horsepower engine, have an NEDC fuel consumption of 9.4L per 100km. The 2022-2.3T-Automatic Four-Wheel Drive Excellence Edition, 2021-2.3T-Automatic Four-Wheel Drive Blade Hero Edition Supreme, and 2020-2.3T-Automatic Four-Wheel Drive Rainforest Cross Edition, equipped with a 231 horsepower engine, have an NEDC fuel consumption of 10.3L per 100km. The 2021-2.0D-Automatic Four-Wheel Drive Blade Hero Edition Xia Ke, Xia Ke Edition (front and rear electronic control locks), and Pioneer Edition, equipped with a 163 horsepower engine, have an NEDC fuel consumption of 8.5L per 100km. The 2021-2.3T-Manual Four-Wheel Drive Blade Hero Edition Pioneer, equipped with a 211 horsepower engine, has an NEDC fuel consumption of 9.7L per 100km. The fuel tank capacity of different BJ40 off-road vehicle models is the same. The distance that can be covered with a full tank of fuel is as follows: Models equipped with a 224 horsepower engine have a fuel tank capacity of 75L, and the distance that can be covered with a full tank is 75/9.9*100=758km and 75/9.4*100=798km. Models equipped with a 231 horsepower engine have a fuel tank capacity of 75L, and the distance that can be covered with a full tank is 75/10.6*100=708km.
19
2
Share

How often should the coolant in the Leiling be replaced?

The coolant in the Leiling should be replaced every two years or 40,000 kilometers. Coolant prevents the freezing of the cooling liquid during cold winter parking, which could otherwise crack the radiator and damage the engine cylinder block. Its full name is antifreeze coolant. Many people think that coolant is only used in winter, but in fact, it should be used all year round. The Leiling is a compact 4-door, 5-seater sedan with dimensions of 4640mm in length, 1780mm in width, and 1455mm in height, and a wheelbase of 2700mm. This car is equipped with a 1.2T turbocharged engine and a CVT continuously variable transmission, delivering a maximum power of 85 kW and a maximum torque of 185 Nm, with a front-wheel drive system.
2
1
Share

How to Measure Cylinder Pressure?

To measure cylinder pressure, follow these steps: 1. Use compressed air to clean the dirt around the spark plugs, then remove all spark plugs. For gasoline engines, also disconnect the ignition system's secondary high-voltage wires and securely ground them to prevent electric shock or fire. 2. Insert the conical rubber tip of the dedicated cylinder pressure gauge into the spark plug hole of the cylinder being measured, ensuring it is properly aligned and tightly sealed. 3. Fully open the throttle (and the choke if equipped), then use the starter to rotate the crankshaft for 3 to 5 seconds (at least 4 compression strokes). Stop rotating once the pressure gauge needle indicates and maintains the maximum pressure reading. 4. Remove the pressure gauge, record the reading, and press the one-way valve to reset the gauge to zero. Repeat this process for each cylinder, measuring each cylinder at least twice. Calculate the arithmetic mean of the measurements for each cylinder and compare the results with standard values to analyze and assess the cylinder's working condition.
17
5
Share

How to Replace the Air Conditioning Filter in a Honda Vezel?

Honda Vezel replacing the air conditioning filter method is: 1. Remove the glove box by pressing inward on these two positions of the glove box. Although the glove box is already open, the left damping hook is still connected; 2. Press down hard on this damping hook, and then you can remove the glove box; 3. Open the cover outside the air conditioning filter, there are clips on both sides, and then you can remove the old air conditioning filter; 4. Replace with a new air conditioning filter according to the direction. The Honda Vezel is a compact SUV with dimensions of 4328mm in length, 1772mm in width, and 1605mm in height, a wheelbase of 2610mm, and a body type of a 5-door, 5-seat SUV.
9
2
Share

How to Replace the Rear Brake Pads on the Envision?

The method for replacing the rear brake pads on the Envision is as follows: 1. Release the handbrake and loosen the hub screws of the wheel where the brake pads need to be replaced, then use a jack to lift the car and remove the tire; 2. Remove the tire to expose the brake caliper and brake disc, and apply lubricant to the screws or nuts that need to be loosened or removed; 3. Hang the brake caliper with a rope and remove the old brake pads; 4. Open the hood and unscrew the cover of the brake fluid reservoir; 5. Install the new brake pads in the correct position. The Envision has a length, width, and height of 4694mm, 1839mm, and 1686mm respectively, with a wheelbase of 2750mm. It is a 5-door, 5-seat SUV with a 7-speed dual-clutch transmission.
17
2
Share

Where is the anti-theft screw of BMW X1?

The anti-theft screw of the BMW X1 is located under the floor of the vehicle's trunk, near the tire removal tools. Its anti-theft principle involves machining the outer diameter of the screw into an irregular shape, which requires the use of a dedicated removal tool specific to the wheel to remove it. The BMW X1 is a compact SUV introduced by BMW Brilliance, with dimensions of 4565mm in length, 1821mm in width, and 1620mm in height, and a wheelbase of 2780mm. It is equipped with either a 1.5T L3 or a 2.0T L4 turbocharged engine, with maximum power outputs of 103kw and 141kw respectively, paired with a 7-speed dual-clutch or an 8-speed automatic transmission.
13
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.