How to Replace the Rear Brake Pads on the Envision?

[RyderLee]

The method for replacing the rear brake pads on the Envision is as follows: 1. Release the handbrake and loosen the hub screws of the wheel where the brake pads need to be replaced, then use a jack to lift the car and remove the tire; 2. Remove the tire to expose the brake caliper and brake disc, and apply lubricant to the screws or nuts that need to be loosened or removed; 3. Hang the brake caliper with a rope and remove the old brake pads; 4. Open the hood and unscrew the cover of the brake fluid reservoir; 5. Install the new brake pads in the correct position. The Envision has a length, width, and height of 4694mm, 1839mm, and 1686mm respectively, with a wheelbase of 2750mm. It is a 5-door, 5-seat SUV with a 7-speed dual-clutch transmission.

[ColtonAnn]

The process of replacing the rear brake pads on the Envision, I've tried it several times myself. First, find a flat and safe place to operate, and engage the parking brake to ensure the vehicle is stable. Prepare the tools: a jack to lift the rear of the vehicle, a wrench or socket to remove the rear wheel nuts, and take off the tire to access the brake assembly. Then, remove the screws of the brake caliper, take out the old brake pads, and clean the caliper area to avoid impurities affecting the installation of the new pads. When installing the new pads, align the holes carefully, place them in, and secure them with screws. Finally, reinstall the tire, lower the vehicle, and test the brake performance to ensure it's normal. The whole process requires attention to detail, and lack of tools might cause delays. Remember to wear gloves to protect your hands—safety first. After completion, it's recommended to test drive at low speed to check for any unusual noises.

[GenevieveFitz]

It's quite rewarding to change the rear brake pads by myself. As an ordinary car owner, I followed a video tutorial to get it done. After finding the correct jacking point to lift the Envision, removing the rear wheel revealed the caliper and old pads. Using a wrench to loosen the fixing bolts, I took out the old pads and compared them with the new ones to ensure the size matched. Before installation, I cleaned the surface of the brake disc to avoid uneven wear. Aligning the new pads properly, I inserted them and tightened the bolts to restore the caliper. Throughout the process, I took my time to avoid dropping tools and causing injury. Finally, I reinstalled the tire and tested the braking effect—no issues meant the job was done. Doing it myself saved me a few hundred bucks, but having all the necessary tools ready is essential. Beginners should consider asking a friend for help to avoid mistakes. I recommend buying OEM parts online to ensure compatibility.

[CourtneyFitz]

Replacing rear brake pads is straightforward: jack up the car, remove the wheel, take off the caliper bolts, and swap in new pads. I've done it a few times; all you need are a jack and basic wrenches. After removing the old pads, check the brake discs for wear—address any grooves if present. Align the new pads properly, ensuring a snug fit. The whole process takes about 30 minutes; don’t forget to reset the caliper. DIY saves money and builds skills, but safety first—keeping the vehicle stable is crucial. After finishing, test the brakes at low speed to confirm normal stopping distance before regular use.

[MalachiAnn]

As an experienced driver, I emphasize the need for caution when replacing rear brake pads. Prepare a jack and gloves, lift the Envision to remove the wheel, and you'll see the brake caliper. Loosen the screws to remove the old pads, and clean the dust with a cloth before installing the new ones. After installation, secure the caliper to ensure the new pads don't move. Be careful with tools to avoid hand injuries during the process; use lubricant if there's rust. Once done, reinstall the wheel and test drive, braking gently a few times at low speed to bed in the new pads. DIY saves time and money, but if you're unfamiliar, it's recommended to practice on a small scale first to ensure you're comfortable before doing a full replacement. Regularly pay attention to brake noises as a sign it's time to replace them.

[RyleeLynn]

Replacing rear brake pads yourself is cost-effective and practical. I used a jack to lift the vehicle, removed the rear wheel nuts to take off the tire. Then I took out the caliper mounting bolts to remove the old pads, cleaned the area, and installed the new pads aligning the holes. When reassembling, I tightened the bolts securely to prevent loosening, and made sure the caliper was properly reset after installation. The whole process requires patience, as beginners might make mistakes like failing to reset the caliper, leading to weak brakes. After completion, test drive to ensure there's no abnormal noise, and regularly check for wear. Sharing my experience, the Envision system is quite stable, but make sure to have all necessary tools on hand to avoid interruptions midway.