Is it necessary to transfer the vehicle files for car ownership transfer?

1 Answers
DiAutumn
08/26/25 2:56am
When transferring the ownership of a motor vehicle, it is necessary to transfer the files. The following is an introduction to vehicle files: Documents required for file transfer: Vehicle license, motor vehicle registration certificate, motor vehicle registration supplementary form, vehicle purchase tax certificate. ID cards of both the buyer and seller. If the buyer is a non-local resident, a temporary residence permit is required, and the buyer's temporary residence permit must have been valid for at least one year. Time for file transfer: Within three days from the date of acceptance, the vehicle management office will annotate the changes on the motor vehicle registration certificate, reclaim the license plate and vehicle license, issue a temporary license plate valid for 30 days, and hand over the motor vehicle files to the owner. The owner must apply for the vehicle transfer at the local vehicle management office within the validity period of the temporary license plate.
Was this review help?
9
1
Share
More Forum Discussions

What are the symptoms of engine cylinder head collision?

Engine cylinder head collision can cause symptoms such as reduced cylinder compression pressure and loss of power. The following are the reasons for engine cylinder head collision: 1. Broken spring: The intake and exhaust valve springs break, causing the valve to fall into the cylinder; possibly due to hard objects falling into the combustion chamber. 2. Excessive gasket thickness: The connecting rod bearing replaced during overhaul is too thick, or the gasket is too thick; or the piston geometric dimensions do not meet the requirements. 3. Cylinder gasket failure: Frequent cylinder gasket failures cause damage to the cylinder block plane. Excessive repair leads to the piston top exceeding the cylinder block plane when the piston moves to the top dead center, resulting in cylinder head collision. 4. Poor fuel quality: The cause of engine cylinder head collision may be the use of poor-quality fuel by the owner, causing the fuel to condense near the valve stem after the engine is turned off, leading to valve sticking when the engine is cold and causing cylinder head collision during startup.
20
1
Share

How to Emergency Release the P Gear on Buick Excelle?

Insert the red T-shaped lever into the small hole in front of the gear shift lever and below the cup holder, then rotate it 90° clockwise. Remove the gear shift lever dust cover to see the emergency release button, and use a screwdriver or other tool to push it forward. There is a white cover plate at the lower left of the instrument panel. Insert a coin into the groove of the cover plate and turn it counterclockwise to open it, then pull the red cable inside. There is a hexagon socket screw and a P gear lever at the middle lower part of the left side of the transmission. Turn the screw upward to lift the P gear lever.
16
2
Share

What is the reason why the Zotye T600 cannot sense the key and fails to start?

Zotye T600 cannot sense the key and fails to start due to a dead key battery and radio interference. The basic components of the remote key consist of the following two points: 1. Transmitter: Composed of a transmission switch, transmission antenna, integrated circuit, etc., it contains an identification code storage circuit and an amplitude modulation circuit, with a button-type lithium battery installed on the opposite side of the circuit. The transmission frequency uses radio waves, and each press of the transmission switch button sends a signal once; 2. Receiver: After the transmitter sends the identification code using shortwave modulation, it is received by the car's shortwave antenna and enters the receiver's electronic control unit through a distributor for demodulation by the shortwave high-frequency amplifier processor, where it is compared with the demodulator's identification code.
17
0
Share

What does ETC display label detachment mean?

It means the device is currently unavailable and needs to be reinstalled and reactivated at the original processing point or any highway ETC service center. Here is additional information: 1. Battery replacement: Most ETC devices display label detachment because users removed the ETC device to replace the battery. 2. Recovery method: The anti-tamper lever on the back of the ETC electronic tag is actually a reset button switch. When the button pops out, the information in the ETC device will be erased and needs to be reactivated with new information. You can try the ETC self-activation method. If that doesn't work, you will have to take it to an ETC processing center or service center to reactivate or cancel the ETC and replace it with a new ETC electronic tag.
14
3
Share

Should the Electric Car Motor Be Repaired or Replaced After Water Damage?

It is best to replace it. If the repair effect is not good, it is better to replace it. Poor repair results may lead to new problems soon after, and could even cause other component failures. From this perspective, replacing it is better than ineffective repairs. The cost of repair is also high, and there is no guarantee of a successful fix. Therefore, it is recommended to replace it. Below is relevant information about water damage in cars: 1. Hazards: If water enters the car, many electronic devices inside can be affected, leading to short circuits and damage. If water enters the engine through the air intake, it can cause severe engine damage. The consequences of water in the engine are very serious, ranging from major engine repairs to potential engine failure. 2. Precautions: During heavy rain, it is best not to drive and instead park the car in a higher area to avoid water damage. If the vehicle is submerged to the point where water enters through the doors, it indicates that the car has been waterlogged. If the car is waterlogged, try to see if it can start. If the car can run without any issues, the first step is to remove the accumulated water inside.
3
2
Share

How to Adjust the Headlight Height on the Buick Excelle?

You can find the headlight height adjustment knob on the left side of the dashboard; the knob is marked with corresponding headlight height positions. Turn the knob to position "0", this is the highest headlight position, pay attention to whether it affects the vehicle. Turn the knob to position "1", this position lowers the headlight height by one level. Turn the knob to position "2", this position sets the headlight height to a relatively lower level. Turn the knob to position "3", this is the lowest headlight position, but make sure the driving visibility remains clear.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.