···
Log in / Register

Should the Electric Car Motor Be Repaired or Replaced After Water Damage?

1Answers
VanRylee
08/28/2025, 10:05:27 PM

It is best to replace it. If the repair effect is not good, it is better to replace it. Poor repair results may lead to new problems soon after, and could even cause other component failures. From this perspective, replacing it is better than ineffective repairs. The cost of repair is also high, and there is no guarantee of a successful fix. Therefore, it is recommended to replace it. Below is relevant information about water damage in cars: 1. Hazards: If water enters the car, many electronic devices inside can be affected, leading to short circuits and damage. If water enters the engine through the air intake, it can cause severe engine damage. The consequences of water in the engine are very serious, ranging from major engine repairs to potential engine failure. 2. Precautions: During heavy rain, it is best not to drive and instead park the car in a higher area to avoid water damage. If the vehicle is submerged to the point where water enters through the doors, it indicates that the car has been waterlogged. If the car is waterlogged, try to see if it can start. If the car can run without any issues, the first step is to remove the accumulated water inside.

Was this review help?
103
Share
More Q&A

How to Adjust the Left Rearview Mirror Most Appropriately for Subject Two?

Adjust the seat to a suitable position. Observe the traffic behind and unfold the rearview mirror. Maintain a normal sitting posture, adjust the height of the rearview mirror, ensuring that the body of the car occupies no more than a quarter of the mirror's reflection.
106
Share

How to reset the tire pressure monitoring on the Sagitar?

The method to reset the tire pressure monitoring on the Sagitar: First, turn on the ignition switch, then press and hold the tire pressure monitoring reset button until you hear a "beep" sound before releasing it. The tire pressure monitoring system will then store the current normal tire pressure data, automatically clear the previous data, and finally, the warning light on the dashboard will go off, completing the tire pressure reset. Tire pressure monitoring is a system that automatically monitors the tire pressure in real-time while the car is in motion, and alerts the driver in case of tire leaks or low pressure to ensure driving safety. There are three commonly used methods of tire pressure monitoring: Direct tire pressure monitoring: Direct tire pressure monitoring devices use pressure sensors installed in each tire to directly measure the tire pressure. The pressure information is then transmitted wirelessly from inside the tire to a central receiver module, which displays the tire pressure data for each tire. The system automatically alerts the driver when the tire pressure is too low or if there is a leak. Indirect tire pressure monitoring: When the pressure in a tire decreases, the vehicle's weight causes the rolling radius of that wheel to become smaller, resulting in a faster rotation speed compared to the other wheels. By comparing the differences in rotation speeds between the tires, the system monitors the tire pressure. Indirect tire pressure monitoring systems essentially rely on calculating the rolling radius of the tires to monitor pressure. Introduction to the Tire Pressure Monitoring System (TPMS): It combines the advantages of both the above systems. Direct sensors are installed in two diagonally opposite tires, and a four-wheel indirect system is also equipped. Compared to using only a direct system, this hybrid system can reduce costs and overcome the limitation of indirect systems, which cannot detect when multiple tires simultaneously have low pressure. However, it still cannot provide real-time data on the actual pressure in all four tires, as a direct system can.
120
Share

How to Fix a Disc Brake That Won't Retract?

Check if the return spring is broken. If it is, replace the return spring promptly. Check if the brake fluid is low. If it is, add brake fluid promptly. Check for oil leaks at the brake wheel cylinder, pipelines, and joints. If there are leaks, go to a repair shop for maintenance or replacement.
106
Share

How to Determine if a Wheel is Out of Round?

Check whether the car deviates from its intended direction while driving. If the direction deviates, it indicates that the wheel is out of round. Check whether the steering wheel shakes during driving and whether the shaking intensifies as the speed increases.
115
Share

How to Step on the Clutch and Brake for Stopping on a Slope in Subject 2?

Observe the vehicle's position, and when it reaches the designated spot, press down on the clutch and brake pedals to stop. Slowly release the clutch while keeping the brake pedal pressed, bring the clutch to the semi-engaged state, wait for a few seconds, and then release the brake.
110
Share

What to Do After Being Rear-Ended and the Other Driver is Fully at Fault, When Handing Over the Car to the 4S Shop?

Prepare the accident liability certificate issued by the traffic police and relevant documents such as the vehicle damage repair cost invoices. Bring the relevant documents and contact the other party's insurance company for claims, including compensation for property damage under compulsory traffic insurance.
109
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.