How to use carlife: 1. carlife only supports Android phones. Download carlife on your Android phone, then connect the phone to the car's infotainment system using a data cable; 2. The car's display will show the carlife interface, which allows you to listen to music, navigate, and use the voice assistant feature to make calls. carlife can reduce the frequency of using your phone while driving, helping the driver focus on driving. Its Chinese name is phone mirroring. After connecting the phone to the car's system, the content on the phone screen can be displayed on the car's screen.

How to use carlife?

How to Install a Rearview Camera on the Volkswagen Tayron?

Here are the steps to install a rearview camera on the Volkswagen Tayron: 1. Remove the rear trunk trim panel and install the camera. 2. After installing the camera, route the wiring along the door edges, remove the reading light, and dismantle the glove box. 3. Connect the wiring to the decoder, then replace it with a 7-inch large screen to complete the installation. Below is more information about the Volkswagen Tayron: 1. The Tayron measures 4590mm in length, 1860mm in width, and 1660mm in height, with a wheelbase of 2731mm. 2. Exterior: Features a honeycomb-shaped front grille paired with LED headlights, a wide lower air intake, and an aluminum roof frame. 3. Interior: The high-end Tayron comes with a 9.2-inch central control screen, the mid-range version has an 8-inch screen, and the base model has a 6.5-inch screen. Mid-range and above models can be equipped with a full LCD instrument panel and dual-color perforated seats. All models come standard with four driving modes: Road Mode, two Off-Road Modes, and Snow Mode. 4. Powertrain: The 2.0T, 1750kg, four-wheel-drive SUV has a fuel consumption of 8.7L per 100km and can accelerate from 0-100km/h in just 6.7 seconds.

109

Share

What's the reason for the Baojun 730 gear disengagement?

Baojun 730 gear disengagement reasons are as follows: 1. Severe wear of transmission gears: The transmission mainly refers to the vehicle's gearbox. If the gears inside the gearbox are worn, it will prevent the vehicle from operating properly. The outer shaft of the gear will exert excessive force, and when this force continuously exceeds the force generated by the spring, it will cause the vehicle to automatically disengage the gear. 2. Weakened or damaged locking spring force: Locking springs are divided into free-type gas springs, self-locking gas springs, balance gas springs, and traction gas springs. Regardless of the type, the spring mainly serves a supporting role, and the elasticity of the spring is crucial. The locking spring piston rod is hollow, and its operating principle involves controlling the gear lever through the rod's wrench mechanism. If the locking spring's force weakens or is damaged, it will cause the vehicle to automatically disengage the gear.

104

Share

How to Repair Automatic Transmission Failures?

Automatic transmission failure repair methods: 1. Automatic transmission oil leakage. Treatment method: If the sealing ring has aged, simply replace it. If the joint surface of the transmission case is damaged, appropriately thicken the paper gasket for repair. However, for severe oil leakage, welding repair is required. 2. Improper throttle cable or throttle position sensor. Treatment method: Requires readjustment of the position. 3. Faulty vehicle speed sensor. Treatment method: Requires replacement with a new one. 4. Engine idling is divided into two situations. One is when the transmission suddenly shifts from a high gear to a low gear, which is likely due to abnormalities in the control system or cooling system. The other situation is a brief slipping and idling phenomenon, which is likely caused by the transmission itself. Treatment method: In this case, it is difficult to resolve on your own and requires professional handling.

116

Share

How often is the annual inspection for overhead cranes required?

The annual inspection for cranes is required once every year. Below is relevant information regarding vehicle annual inspections: 1. Inspection Time: The owner of the motor vehicle can apply for the inspection compliance mark at the vehicle management office of the registration location within three months before the expiration of the motor vehicle's inspection validity period (for small cars registered after September 2012, the inspection is required once every six years). The inspection should be conducted within three months before the expiration date of the vehicle's registration certificate. 2. Materials: Before the annual inspection, check the validity date of the compulsory traffic insurance that includes the vehicle and vessel tax. If it has expired or will expire within three months after the inspection date, it is recommended to renew it in advance. The ID card of the vehicle owner or the agent; the vehicle registration certificate.

104

Share

How many liters of engine oil should be added to a BMW 320Li?

BMW 320Li with chassis model F35 is a four-door long-wheelbase version, equipped with an N20 engine. The standard engine oil capacity is 5L. However, if it's for engine maintenance where the system is completely drained and some components require lubrication during assembly, an additional 1-1.5 liters of oil may be needed. Below is an introduction to engine oil: 1. Engine oil serves multiple functions including lubrication and friction reduction, auxiliary cooling, sealing and leak prevention, rust and corrosion protection, as well as shock absorption. It is often referred to as the 'blood' of a car. The engine is the heart of a vehicle, containing numerous metal surfaces that move against each other under high-speed and harsh conditions, with operating temperatures reaching 400 to 600 degrees Celsius. Only qualified lubricating oil can reduce wear on engine components and extend their service life under such severe conditions. 2. The amount of engine oil added should ideally be between the upper and lower marks on the dipstick. Excessive oil can enter the combustion chamber through the gap between the cylinder and piston, forming carbon deposits. These deposits can increase the engine's compression ratio, raising the likelihood of knocking. Carbon deposits in the cylinder, which can become red-hot, may also lead to pre-ignition. If they fall into the cylinder, they can accelerate wear on the cylinder and piston and further contaminate the lubricating oil.

113

Share

How to Fold Down the Rear Seats in a Buick LaCrosse?

Open the trunk and locate the two release straps inside. Pull the strap on the side corresponding to the seat you wish to fold down to unlock the rear seat. Fold the seatback downward. Lift the seatback, push it backward, and lock it into position. Ensure the seatbelt is not twisted or caught by the seatback. Push and pull the top of the seatback to confirm it is securely locked. Additional relevant information is as follows: 1. The Buick LaCrosse features fold-down rear seatbacks on both sides to provide additional cargo space. Only fold the seatbacks when the vehicle is stationary. If any seatback is not locked, it may move forward during emergency braking or a collision, potentially causing injury to passengers. Always push and pull the seatback to ensure it is locked. Folding the rear seats while seatbelts are fastened may damage the seats or seatbelts. 2. The new Buick LaCrosse and LaCrosse Avenir are equipped with the eighth-generation Ecotec 2.0T variable-cylinder turbocharged engine paired with a 9-speed HYDRA-MATIC intelligent transmission, delivering a maximum power output of 177kW/5000rpm and maximum torque of 350Nm/1500~4000rpm. Not only does it meet China's National VI emission standards, but the engine can also intelligently switch between "four-cylinder high-performance mode," "four-cylinder economy mode," and "two-cylinder ultra-economy mode" based on driving conditions, maintaining uncompromised power performance while achieving fuel consumption as low as 6.9L per 100km.

107

Share