How to Turn on the Fog Lights on the Tayron?

1 Answers
DelKinsley
07/29/25 8:23pm
The fog lights on the Tayron can be successfully turned on by rotating the knob to the position of the parking lights. Below is a detailed introduction on how to turn on the fog lights on the Tayron: 1. The switches for the front and rear fog lights are located below the left side of the steering wheel. The fog lights can be turned on by rotating the knob to the corresponding position: rotate the knob to the position of the parking lights, pull it out once to turn on the front fog lights, and pull it out again to turn on both the front and rear fog lights. Rotate the knob back to the off position to turn off the fog lights. 2. Fog lights are installed on the front and rear of the car. There are two ways to turn on the fog lights: button activation and rotation: there is a button marked with fog lights near the instrument panel. After turning on the lights, press the front fog light button to turn on the front fog lights, and press the rear fog light button to turn on the rear fog lights; when the button marked with the fog light signal in the middle is twisted to the ON position, the front fog lights are turned on. Then twist the button down to the rear fog light position to turn on both the front and rear fog lights simultaneously.
Was this review help?
17
4
Share
More Forum Discussions

What does autohold mean in a car?

Autohold in a car refers to the automatic parking function, which is a type of automatic braking feature. Once activated, for example, when stopping at a traffic light, it eliminates the need to pull the handbrake, avoiding the use of either the manual or electronic handbrake and simplifying operations. For automatic transmission models, it also reduces the need for frequent gear shifts between D to N or D to P. The autohold function enables the vehicle to automatically apply braking to all four wheels when stopping at traffic lights or on slopes, keeping the car stationary even in D or N gear without the need to continuously press the brake pedal or use the handbrake. To release the stationary state, simply tap the accelerator to disengage the brake. This feature is particularly useful for drivers who frequently encounter stop-and-go traffic in urban areas, while also reducing unnecessary accidents caused by negligence.
5
3
Share

What is the reason for the ABS light being on?

The reasons for the ABS light being on are: 1. The ABS wire is broken or the plug is loose; 2. The electronic control device is of poor quality; 3. The fuse has blown for some reason. If the ABS light does not come on when the ignition switch is first turned on, the reason may be that the speed signal has not been transmitted to the ABS control unit. If the ABS sometimes works and sometimes doesn't, the reason may be a mechanical failure. If the ABS light is frequently on, it means the system has detected an ABS system error, and it is recommended to have it checked as soon as possible, as this is directly related to travel safety. When a fault occurs, it is necessary to first determine whether the vehicle's usual travel environment and the obstacles encountered by the car are related to the ABS fault, and then make corresponding repairs. Usually, the ABS light is on for a very short time, and if the system detects no problems after self-checking, it will turn off by itself. If you press the brake pedal quickly to the bottom while driving, the ABS light will also come on. Additionally, when the car is started, the ABS light may come on, but it will turn off when the brake is released.
6
2
Share

What does the service light indicate?

service is not a fault indicator light, but rather a reminder function set by the manufacturer to prompt vehicle owners to perform maintenance according to the mileage. After maintenance is completed, the service reminder light needs to be reset following a specific procedure before it will turn off. Generally, automobile manufacturers stipulate maintenance intervals, commonly at 5,000, 7,500, or 10,000 kilometers. Following the maintenance schedule as specified in the owner's manual is highly recommended. Vehicle maintenance refers to the preventive work of regularly inspecting, cleaning, replenishing, lubricating, adjusting, or replacing certain components of a vehicle, also known as vehicle servicing. Modern vehicle maintenance primarily includes servicing for the engine system, transmission system, air conditioning system, cooling system, fuel system, power steering system, and more. The purpose of vehicle maintenance is to keep the vehicle clean and tidy, maintain normal technical conditions, eliminate potential hazards, prevent faults, slow down the deterioration process, and extend the vehicle's service life.
1
5
Share

What are the correct steps for using an electronic parking brake?

The correct steps for using an electronic parking brake are: 1. Parking: Step on the brake, shift to P gear, pull up the electronic parking brake once, you can hear the sound of the brake tightening, and the onboard computer will display that the electronic parking brake is activated; 2. Starting: Step on the brake, shift to D gear, press the electronic parking brake once, release the brake to start. Some vehicles automatically activate the electronic parking brake after stopping, and when starting, simply step on the accelerator to automatically release the electronic parking brake. Pulling up the electronic parking brake while driving at high speed is ineffective; it only functions when the vehicle speed is nearly stopped (generally around 10km/h).
9
0
Share

How to Achieve the Surface Finish of the Guide Sleeve Inner Groove?

CNC lathe processes stainless steel to the required precision, including dimensional tolerance and geometric tolerance, while ensuring a machining allowance of 1-2 microns is left. The equipment is installed on the lathe tool holder to perform mirror finishing on the stainless steel. Turn on the control cabinet switch, perform tool setting, feed, and retract the tool to complete the stainless steel mirror finish.
13
5
Share

What to do when a tubeless tire separates from the wheel hub?

Check the tire and rim for any damage, then directly reinstall the tire onto the rim to reset it. Find a high-power air pump to inflate the tire. Tubeless tires rely on air pressure to stay attached to the steel rim—the more air pressure, the less likely it is to lose air.
5
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.