How to Turn on the Cold Air in a Subaru Air Conditioner?

Subject 2: Should You Pull the Handbrake or Shift Gears First When Getting Out of the Car?

After completing the driving test for Subject 2, when getting out of the car, you can first shift to neutral and then pull the handbrake. Of course, you can also pull the handbrake first and then shift to neutral. There are no specific requirements for this sequence, and you can operate according to personal habits. Just remember not to forget to pull the handbrake and shift to neutral. Below is the relevant introduction: 1. Handbrake: The professional term for the handbrake is the auxiliary brake. Unlike the principle of the main brake, it uses a steel wire cable connected to the rear brake shoes to brake the car. Long-term use of the handbrake will cause the steel wire to undergo plastic deformation. Since this deformation is irreversible, long-term use will reduce its effectiveness, and the handbrake's travel will also increase. 2. Return Spring: The handbrake is also used in conjunction with a return spring. When the handbrake is pulled for braking, the spring is stretched; when the handbrake is released, the spring returns to its original length. Long-term use of the handbrake will also cause corresponding deformation in the spring.

2

Share

What are the reasons for failing the review of Subject 2 training hours?

The reasons for failing the review of Subject 2 training hours are generally two-fold. If both the training hours and mileage meet the requirements, then it is likely due to unqualified photos, which requires returning to the driving school to retake some photos. It could also be a system data error. If the training hours review is not passed, you should contact the driving school. If the issue cannot be resolved, the driving school will report the problem to the vehicle management office, which will address it as soon as possible. Below are the relevant details: 1. Training hours: According to the "Motor Vehicle Driver Training Teaching and Examination Outline," for the Subject 2 test of C1 and C2 driver's licenses, generally 16 or 14 training hours are required. However, regulations may vary in different regions, so the specific hours should comply with local requirements. 2. Learning items: Subject 2 training is divided into theoretical knowledge and practical operations. Theoretical knowledge includes basic driving operation norms and site driving knowledge, usually arranged for 2 hours of study. Practical operations involve basic driving skills such as driving posture, getting in and out of the car, starting and stopping, as well as the study of Subject 2 test items.

15

2

Share

How Long Does It Usually Take to Practice for Subject 2?

Usually 12-22 days. Here are the relevant details: 1. Training Hours: For C1 and C2 driver's license training in driving schools, the theoretical training for Subject 2 must reach 2 hours, and the practical training must reach 22 hours before taking the test. However, this standard is not strictly enforced, as many driving schools submit the exam list based on the students' proficiency level, meaning the practice time is not fixed. If you want to take the test as soon as possible, you should increase the frequency of your practice sessions at the driving school. 2. Notes: During the pre-driving preparation, you must adjust the seat and fasten your seatbelt before verifying your fingerprint. Each test item in the examination area is monitored by GPS positioning, and the control line (yellow dotted line) of each item represents the test area for that item. Once the front of the vehicle passes the control line, it means you have entered the test for that item and must complete it according to the test rules.

13

4

Share

Is Gear Shifting Required in Subject 2?

Gear shifting is not required in the Subject 2 driving test. The vehicle should remain in first gear when moving forward, and the semi-clutch method can be used to control the speed. Reverse gear is used for reversing into the parking space and parallel parking. Below are some relevant details: 1. Test Tips: Carefully control the accelerator and brake. Use the brake to slow down and the accelerator to speed up, but avoid pressing either too forcefully. For safety, it is recommended to maintain a slow speed throughout. During hill starts, be careful to prevent the vehicle from rolling back. Gradually release the brake only when you feel the car has enough power to climb the slope. 2. Failing the Test: If you fail the Subject 2 test on the first attempt, you are allowed one retake. If you do not take the retake or fail it again, the test session ends, and the applicant must reschedule the test after ten days. Within the validity period of the driving skill test permit, the number of test reschedules for Subject 2 and Subject 3 road driving skill tests must not exceed five times.

7

4

Share

How to Install a Beam Wiper Blade?

Beam wiper blade installation steps are as follows: 1. The wiper and U-bar must form a 90-degree angle to remove the old wiper blade. Lift the wiper upwards until it is perpendicular to the windshield, then pull out the U-bar. 2. After removing the old wiper, install the new beam wiper blade. Gently press the "buttons" on both sides of the slot with your fingers, and the middle cover will open. 3. Insert the U-bar, snap the cover into place, and smooth it out to complete the installation. Related introduction to beam wiper blades: A beam wiper blade consists of four components: the wiper rubber, beam wiper steel strip, wiper cover, and plastic parts. The bracket is made of stainless steel, the steel strip is carbon steel with a length between 10-28 inches, a thickness of 0.80~0.90 mm, and a width generally between 7.00~14.00 mm.

19

5

Share

Can You Turn on the Wiper During Driving Test Subject Two in the Rain?

You can turn on the wiper. Here are some precautions for driving test subject two on rainy days: 1. Adjust your mindset: The most important thing for a rainy day test is your mindset. When encountering rain during the test, you must not have negative emotions or be overly nervous. Therefore, candidates must adjust their mindset during the test, maintain an optimistic mood, and not let the weather affect them. 2. Preparations before getting in the car: The rearview mirror may become blurry in the rain, so candidates must wipe the rearview mirror clean before getting in the car to avoid unclear visibility during the test. Before getting in the car, candidates should shake off mud and water from their feet to prevent slipping when stepping on the pedals. Driving in the rain makes the wheels prone to skidding. Therefore, during the test, candidates should control the speed of the car, which should be slower than during normal training. 3. Braking: Brake pads are prone to skidding in the rain, so when braking, you should apply slightly more force than usual. 4. Turning on the wiper: Generally speaking, not turning on the wiper does not have a significant impact on the test. However, it should be noted that before stopping at the designated point on the slope, turn on the wiper to clean the rainwater on the front windshield, then turn it off to prepare for the designated stop.

14

2

Share

How to Turn on the Cold Air in a Subaru Air Conditioner?

Subject 2: Should You Pull the Handbrake or Shift Gears First When Getting Out of the Car?

What are the reasons for failing the review of Subject 2 training hours?

How Long Does It Usually Take to Practice for Subject 2?

Is Gear Shifting Required in Subject 2?

How to Install a Beam Wiper Blade?

Can You Turn on the Wiper During Driving Test Subject Two in the Rain?

What does it mean when the fixed point for hill start is less than 50 centimeters?

What is the istana car?

What does Level 3 water-damaged vehicle mean?

What to Do If There Are Small Bubbles in Car Film?