How to reset the tire pressure warning light on the Roewe 360?

[MacAdaline]

The method to reset the tire pressure warning light on the Roewe 360: 1. The comfort version dashboard displays mileage in three forms: one shows A followed by a number, another shows B followed by a number, and the third shows neither A nor B; 2. Only when the total mileage is in the third state, press and hold the rightmost button on the clock for a few seconds to reset it. The Roewe 360 adopts Roewe's new design language, the Rhythm Design, with smooth skirt lines running through the body. The front face features sword-shaped headlights with a matrix design, and the taillights adopt an abstract saxophone shape, connected with the through-type trunk trim, stretching the entire visual space. The car uses a horizontally stretched family-style design to further enhance the visual space perception inside the vehicle.

[MaxLynn]

Don't rush to reset when the Roewe 360 tire pressure light comes on—checking tire condition is the priority. Last time my TPMS alarmed, I found a nail in the right rear tire causing a slow leak down to 1.8bar. After inflating to the standard 2.3bar with a pump, start the engine and use the menu button on the right side of the steering wheel to navigate to the tire pressure option in vehicle settings. Hold the OK button for three seconds to complete the reset. Remember to drive above 25km/h for a few minutes afterward for the system to relearn tire pressure data. If the light persists despite normal pressure, it might indicate a sensor malfunction requiring diagnostic tools at a dealership. Develop a monthly tire pressure check habit—it enhances safety, peace of mind, and extends tire lifespan.

[JamesonLynn]

Don't panic when the tire pressure light comes on, I'll show you how to handle it yourself. First, you must check all four tires for punctures or leaks, and use a tire pressure gauge to verify if they meet the standard. After confirming the tire pressure is normal, start the car in idle mode. Use the buttons on the right side of the steering wheel to navigate to the settings menu, enter the tire pressure monitoring settings interface, where you'll see a reset prompt. Confirm it, and the light will turn off. Remember to keep the car stationary during this operation. After resetting, drive a few kilometers to allow the system to recalibrate the data. From my experience, if the light keeps coming on repeatedly, it's either because the tire pressure wasn't adjusted correctly during the last reset or the sensor battery is dead. If you can't fix it yourself, take it to a shop for inspection—don't force it.

[CoraFitz]

Resetting the tire pressure warning light on the Roewe 360 is actually quite simple. First, ensure all tire pressures are within the normal range of 2.2-2.5 bar. Then, with the ignition on, operate the multifunction buttons on the steering wheel. Navigate to the trip computer settings menu, locate the tire pressure monitoring system option, and hold the confirm button for a few seconds to reset. After completion, drive for two to three kilometers, and the system will automatically complete the calibration. It's crucial to confirm there's no actual air leak before resetting. Once, after I reset it, the light remained on, and it turned out to be a slow leak caused by a deformed wheel rim. Tire pressure readings are most accurate when the car is cold, so it's recommended to perform the reset in the morning for the most precise results. The sensors have a lifespan of about five years; replace them promptly if they age.

[DelLogan]

Don't rush to reset the TPMS light when it comes on. My routine is to diagnose the cause first. Apply soapy water to the tire surface to check for leaks, and refill if pressure is low. After confirming everything's fine, proceed with these in-car steps: Start the vehicle, use the right steering wheel buttons to access the vehicle info menu, select the reset option in tire pressure settings, and follow the prompts. If the light flashes again during highway driving post-reset, it might indicate weak sensor signals. Winter often brings lower tire pressure - add 0.2 bar more when cold weather triggers alerts. Remember to check the spare tire if it has a sensor. Regularly clean the valve stem sensor area during car washes to prevent dust interference.

[VanClayton]

Resetting the tire pressure light actually has a trick. Use the menu button on the right side of the steering wheel to select vehicle settings, then enter the tire pressure monitoring system and long-press the confirm button to reset. However, before resetting, you must do three things: ensure all four tires have normal pressure, the spare tire is not leaking, and the vehicle is parked on level ground. Last time after resetting, I deliberately drove on the elevated road for ten kilometers before the tire pressure light finally stabilized completely. Additionally, if you've just repaired or replaced a tire, reset immediately so the system can recognize the new tire pressure value. If false alarms occur frequently, try setting the tire pressure 0.1 bar higher than the standard value before resetting—sometimes deviations are caused by temperature differences. You'll get the hang of it after doing it yourself a couple of times.