···
Log in / Register

How to reset the service light after maintenance for Peugeot 408?

6Answers
Clinton
09/05/2025, 02:21:29 AM

The method to reset the service light after maintenance for Peugeot 408: 1. Turn on the vehicle power supply and reset the small mileage on the dashboard; 2. Press the right button to switch the display to instantaneous fuel consumption; 3. Turn off the power supply, then press and hold the right button without releasing, turn on the power self-check, continue to press the right button for three seconds, then release the right button; 4. Simultaneously press both left and right buttons, release both buttons within two seconds to complete the reset. Taking the 2020 Peugeot 408 230THP 10th Anniversary Edition as an example: It is a compact car launched by Dongfeng Peugeot, with a length, width, and height of 4750mm, 1820mm, and 1488mm respectively, a wheelbase of 2730mm, equipped with a 1.2T turbocharged engine, a maximum power of 100kw, and matched with a 6-speed dual-clutch transmission.

Was this review help?
107
Share
SanCassandra
09/17/2025, 02:41:27 AM

I also encountered the service light issue after my last Peugeot 408 maintenance. It's not difficult to reset. First, sit in the car, insert the key and turn it to the accessory position without starting the engine – just make sure the dashboard lights up. Locate that small button, usually the trip meter reset button, and hold it down for about 10 to 15 seconds. You'll see the service light blink once and then turn off, indicating it's done. Don't worry about making mistakes; the manual should have illustrations. If the light doesn't go off, it might mean the maintenance isn't fully completed. Check items like engine oil or the cabin air filter again to ensure the car's condition is OK before trying the reset again. Remember, this alert is a maintenance reminder – even after resetting it yourself, you should still note down the next service interval.

Was this review help?
10
Share
Expand All
StGriffin
10/31/2025, 03:12:28 AM

Every time after maintenance, I have to deal with this warning light, which is quite annoying. The reset method is simple: turn the key one click to power up the electronics without starting the engine. Glance at the dashboard, press and hold the reset button until the light goes out, then release. DIY is convenient and saves a trip to the repair shop. However, a reminder: when the service light comes on, it means maintenance is due. If resetting doesn't solve it, there might be a real issue, so it's advisable to visit the shop directly. Before resetting, ensure there are no actual problems to avoid overlooking potential faults that could affect driving safety.

Was this review help?
6
Share
Expand All
OJoshua
12/14/2025, 02:20:38 AM

To reset the service light on my Peugeot 408, turn the key to the accessory position without starting the engine, then press and hold the reset button until the light goes off. This trick works—just a few minutes at home. If it doesn’t work, check the manual or follow an online video; it’s really simple. Remember, don’t reset the maintenance reminder randomly—ensure the car is in good health before proceeding.

Was this review help?
15
Share
Expand All
MacJayce
02/03/2026, 03:20:36 AM

I've also encountered the service light coming on, and it needs to be reset after maintenance. The usual method is to turn the key to the on position without starting the engine, then press and hold the instrument panel button for a few seconds until the light disappears. If it doesn't work the first time, don't panic—just turn off the key and try again. I've done this a few times with good results. It's worth noting that this light serves as a maintenance reminder, so after resetting it, keep an eye on your vehicle's condition and don't ignore any real issues. For safety, always check tires and fluid levels after maintenance.

Was this review help?
1
Share
Expand All
Daphne
04/29/2026, 12:56:24 PM

Removing the Peugeot 408 maintenance reminder is simple: turn on the ignition without starting the engine, then press and hold the reset button until the light goes off. The computer system will reset this way. I recommend ensuring the battery is sufficiently charged before operation and avoiding pressing wrong buttons. The light should disappear after maintenance, but if it lights up without maintenance, it needs attention. If the operation fails, there are many online tutorials available. Keep good maintenance records for your car regularly.

Was this review help?
3
Share
Expand All
More Q&A

Are the three major components of the Regal and Malibu XL the same?

Are the three major components of the Regal and Malibu XL the same? Below are the relevant introductions: 1. Intelligent Cylinder Deactivation Technology: The most notable feature of General Motors' eighth-generation Ecotec engine is its intelligent cylinder deactivation technology, which allows for intelligent switching between four-cylinder and two-cylinder operation modes. Combined with the 35Mpa high-pressure direct injection system and active thermal management system, it achieves higher combustion efficiency. 2. Structural Layout: The selection of gear sets, clutches, and torque converters follows specific strategies. The mechanical combination of 5 sets of planetary gear mechanisms, 4 fixed clutches, and 3 rotating clutches achieves an optimal gear ratio range of 7.6:1, optimizing the vehicle's acceleration performance and fuel economy.
107
Share

What are the differences between the Corolla Pioneer Edition and Pioneer Plus?

The differences between the Corolla Pioneer Edition and Pioneer Plus are as follows: 1. Horsepower: The maximum horsepower of the Pioneer Edition's engine is 121 hp, while the Pioneer Plus's engine has a maximum horsepower of 116 hp. 2. Torque: The maximum torque of the Pioneer Edition's engine is 148 Nm, while the Pioneer Plus's engine has a maximum torque of 185 Nm. 3. Body type: Both the Corolla Pioneer Edition and Pioneer Plus feature a 4-door, 5-seater sedan body type, equipped with a CVT transmission (simulating 10 gears), a top speed of 180 km/h, a fuel tank capacity of 50 liters, and a front-wheel-drive system.
104
Share

What Causes BMW Cruise Control Failure?

BMW cruise control failure can be attributed to the following reasons: 1. ACC sensor malfunction: Damaged ACC sensor, dirty ACC sensor, damaged plastic cover in front of the ACC sensor, or external interference with the ACC sensor's radar signal. 2. Control unit internal or wiring failure: If there is an issue within the control unit or a fault in the connecting wiring, the signal cannot be transmitted. 3. Wheel speed sensor: If the cruise control system failure warning appears alongside alerts related to DSC, ABS, or RPA, it is highly likely due to poor performance of the wheel speed sensor.
118
Share

Can I drive if the car's radiator is out of water and smoking after adding water?

As long as the car can still start without smoking and run, it should be fine. Here are the relevant details: 1. Precautions: In a cold state, if the radiator is out of water, the car can generally drive for about 1-3 kilometers. However, if it's in a hot state, continuing to drive will damage the engine. If you encounter a situation where the radiator is short of water while driving, do not use tap water as a substitute. Tap water contains minerals that can form scale in the radiator pipes when heated. Severe scale can clog the engine's cooling system. 2. Car radiator water shortage warning: If the car's radiator is out of water, the dashboard will display a water shortage indicator. The indicator looks like a thermometer and is relatively easy to identify. It is not recommended to continue driving after the car radiator water shortage warning light comes on. If the radiator is short of water, the heat generated during the engine's operation cannot be released, and the engine's performance, durability, and exhaust emissions will not meet the requirements.
109
Share

Can Car Vacuum Cleaners Be Left in the Car During Summer?

Car vacuum cleaners can be left in the car during summer. Here are the relevant details: 1. Types: There are generally two types: one that uses batteries, which can be charged at home and used independently of the car, and another that draws power from the cigarette lighter, designed for plug-and-play use with power circuits meeting the cigarette lighter's supply standards. 2. Precautions: Before using a car vacuum cleaner, check if the power fuse can handle the startup and operating current of the vacuum cleaner. When the dust reaches a certain level or after use, clean it by pressing the clip on the dust cover to open and remove the dirt. It's advisable to wear a mask while vacuuming, as using the cleaner can stir up dust, making it easier to inhale. Never place hands or feet under the suction opening to avoid danger. Watch for any blockages in the suction tube, unusual noises, or smoke during use. If any of these occur, stop using the vacuum immediately. Clear any blockages before continuing use; otherwise, the vacuum's motor may burn out.
113
Share

How to turn on the front fog lights of a Ford Focus?

The method to turn on the front fog lights of a Ford Focus is: 1. Press the vehicle's one-touch start button to power on the vehicle; 2. Locate the vehicle light control button on the lower left side of the steering wheel; 3. Rotate the central knob to turn on the vehicle lighting system; 4. Press the front fog light button to activate the front fog lights. Functions of fog lights: 1. Front fog lights are used to improve illumination when road conditions ahead are unclear and to alert oncoming drivers; 2. Rear fog lights help vehicles behind to spot the car in low visibility conditions. Taking the 2021 Ford Focus as an example, its body structure is a four-door, five-seat sedan with dimensions of 4674mm in length, 1810mm in width, and 1468mm in height, a wheelbase of 2705mm, a fuel tank capacity of 53 liters, a trunk capacity of 511 liters, and a curb weight of 1242kg.
110
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.