How to reset the maintenance wrench on JAC Refine M3?

[DiAlexa]

Turn off the ignition switch, press and hold the button on the combination meter, turn on the ignition switch, rotate the switch to the ACC position to power on the vehicle. The length, width, and height are 4715mm, 1765mm, and 1900mm respectively, with a wheelbase of 2810mm. The top speed is 210 km/h, equipped with a 5-speed manual transmission, and the tire specification is 205/65R15. The vehicle is equipped with a driver's seat belt reminder, tire pressure warning, and rear radar, with a front-engine rear-wheel-drive layout.

[SanBentley]

I remember being quite annoyed when the maintenance wrench light on my JAC Refine M3 came on, but it's not difficult to clear it yourself. First, turn off the car without starting the engine, then press and hold the small trip reset button on the dashboard. Without releasing the button, turn the key to the ON position (power on but engine off), and keep holding for about 5 to 10 seconds until the wrench light goes out. Once the light is off, you can release the button. I've tried this method several times, and it worked every time. However, the light serves as a reminder for maintenance, so I suggest checking the manual to confirm the mileage before clearing it to avoid overdue oil changes or filter replacements. It's more reasonable to clear the light after completing the maintenance. Also, pay attention to engine noise or fuel consumption changes while driving to catch small issues early and save big on repairs. Safe driving habits are important—never operate this button while driving.

[McEliza]

For car enthusiasts who enjoy DIY repairs, clearing the maintenance reminder light is simple. First, turn off the engine, press and hold the trip button on the dashboard, turn the key to the ON position to power up the system, wait a few seconds, and the wrench light will flash and then turn off. This process resets the vehicle's maintenance counter, saving time for DIYers. When the light comes on, it's best to check the engine oil level and air filter condition. Timely maintenance can improve engine efficiency. If the light remains on after clearing, it may indicate a sensor malfunction or wiring issue. It's recommended to consult the manual for troubleshooting or seek professional repair. Don't overlook the details in routine maintenance to extend your car's lifespan, saving money and ensuring peace of mind.

[LaTravis]

I quickly resolved the wrench light issue on my Refine M3. First, turn off the car, press and hold the dashboard button, turn the key to the power-on position, and wait for the light to go out. It's quite convenient. However, when the light comes on as a reminder for maintenance, I usually go directly to the 4S shop to have them reset it and get a check-up for peace of mind. The operation is simple, so don't worry. Just make sure to change the oil and filters regularly and maintain the vehicle's condition. Clearing the light but ignoring the underlying issue can be troublesome. Safety first, don't delay.

[Holly]

When I was a new driver, I encountered the M3 maintenance light turning on. The method to clear it is to turn off the car, hold the small button on the dashboard, turn the key to the power-on state, and keep pressing for a few seconds until the light disappears. Before performing this operation, make sure you have completed the maintenance, and don't rush to clear the reminder. Daily maintenance, such as regular oil changes, is crucial to avoid engine damage. If you don't clear the light, it will keep flashing, which can affect your driving mood. New drivers should pay attention to safety and ensure the vehicle is stationary when performing the operation. After completing these simple steps, drive a few more times to familiarize yourself with the car's feedback.

[AmirAnn]

My friend's car had the maintenance light on, and I taught him: Turn off the engine, press and hold the instrument button, turn the key to the ON position, and wait for the light to go out. It worked pretty well, and he cleared it quickly. The light is just a signal not to exceed the mileage for maintenance. After resetting, you should change the oil or check the filters to extend the vehicle's lifespan. If the light keeps coming on, check the battery voltage or sensors. Sharing experiences regularly can save you trips to the dealership. Give it a try yourself—don’t stress, it’s quick and won’t affect daily use.