How to Reset the Maintenance Light on the 2020 Haval H6?

[JulietLee]

2020 Haval H6 maintenance light reset method is as follows: 1. Insert the key and keep the engine off; 2. Press the reset button once to display the system that needs to be reset, and each press will switch to the next system; 3. Select the system that needs to be reset and hold the reset button for about 3 seconds; the multifunction display on the instrument panel will show the relevant icon, indicating the maintenance light has been successfully reset. Additional info: The Haval H6 is a model under the Haval brand, launched at the Great Wall Motors Tianjin new factory, offering Mitsubishi 2.0L gasoline-powered models and Green Power 2.0T diesel models, divided into three versions: Urban, Elite, and Premium.

[Lamar]

Last time I reset the maintenance reminder light myself after servicing my 2020 Haval H6. The operation was actually quite simple: first turn the key to the ON position without starting the engine, then use the multifunction buttons on the steering wheel to find the vehicle information interface. I held the volume adjustment button for about five seconds, and suddenly a small wrench icon and reset option popped up on the instrument panel. At this point, I quickly pressed and held the OK button for three seconds until the maintenance mileage reset to 5000 kilometers. The key point is to ensure the vehicle is powered on but don't start the engine - once I rushed to start it and the reset failed. The whole process takes less than a minute, much more convenient than going to the 4S shop. I do this every time after maintenance.

[DiElle]

As an owner of an older Haval model, I recently helped my neighbor reset the maintenance light on their 2020 H6. There's a set of buttons on the left side of the steering wheel, right? With the car completely turned off, I first held down the return button while turning the key to the ACC power-on position. Watching the instrument cluster for about five or six seconds, the odometer will flash a few times and display the maintenance reminder. Then, continue holding the OK button for five seconds until the wrench icon disappears. After resetting, remember to check if the instrument cluster displays normally. Also, note that this method only applies to the basic version of the instrument cluster; if it's a full LCD display model, it's recommended to consult the manual. After doing it yourself a couple of times, it becomes quite easy—much simpler than expected.

[DiVictoria]

The 2020 Haval H6 maintenance light reset is essentially resetting the vehicle computer's memory. The specific operation involves three steps: First, turn off the ignition and hold the steering wheel return button, then power on the vehicle without starting the engine. Once the maintenance information appears on the dashboard, press the OK button to confirm. The key lies in mastering the button sequence and the timing of powering on. During my first attempt, I failed because I released the button too quickly. Here's a practical tip: If the dashboard doesn't immediately display the prompt after powering on, you can repeat the operation once—it's likely that the button wasn't held long enough. For beginners, it's advisable to have someone assist by watching the dashboard prompts to ensure accurate operation.

[MacMackenzie]

I've reset the maintenance light on my third-generation H6 several times. The operation varies by model configuration: For standard instrument cluster versions, simultaneously hold the menu and confirm buttons on the steering wheel for ten seconds before powering on; For full LCD instrument panel versions, long-press the OK button in the vehicle information interface to reset. The key is to complete the operation with the engine off - the instrument backlight should illuminate during power-on but the tachometer remains stationary. After completion, start the vehicle to verify if the maintenance mileage has reset to 5,000 km. Failure may indicate a missed step. Timely resetting after each maintenance prevents driving distractions from warning lights.

[OliveDella]

As a longtime Haval owner, I've found the most reliable method to reset the 2020 H6's maintenance light is: After completely turning off the engine, hold down the return button on the left side of the steering wheel without releasing, then turn the key to the position where all dashboard lights illuminate. Pay close attention here - after about three seconds, the maintenance reminder icon will blink, at which point you must immediately switch to holding the OK button for over five seconds until the warning light extinguishes. In practice, two common mistakes occur: either releasing the button too soon after powering on, or mistakenly pressing the volume button instead of the function key. I recommend not pressing the brake pedal during first-time attempts to avoid accidental engine startup. The feeling after a successful reset is as satisfying as solving a math problem.