···
Log in / Register

What is the difference between Volkswagen Passat 330 and 380?

1Answers
KingstonDella
07/25/2025, 03:41:02 AM

The difference between Volkswagen Passat 330 and 380 lies in their power output: the Volkswagen Passat 330 has a maximum power of 137kw, maximum torque of 320nm, and maximum horsepower of 186ps; the 380 has a maximum power of 162kw, maximum torque of 350nm, and maximum horsepower of 220ps. Both the Volkswagen Passat 330 and 380 have the same body dimensions: length 4933mm, width 1836mm, height 1469mm, and a wheelbase of 2871mm. Both models are equipped with a 2.0t turbocharged engine, featuring a front suspension type of MacPherson independent suspension and a rear suspension type of multi-link independent suspension.

Was this review help?
108
Share
More Q&A

How to Turn on the Heater in a Chevrolet Cruze?

Method to turn on the heater in a Chevrolet Cruze: 1. After starting the Chevrolet Cruze, wait approximately 8-15 minutes for the engine to reach normal operating temperature before turning on the heater. 2. Adjust the air conditioning system to recirculate air inside the vehicle. 3. Set the Chevrolet Cruze's air conditioning to the heating mode, which is often indicated by a red zone on some vehicles. 4. Do not turn on the air conditioning compressor (do not activate the AC switch), as the heater utilizes the vehicle's own heat cycle to save energy. 5. Adjust the air conditioning to a suitable fan speed and direct the airflow as desired. 6. The direction of the warm air is generally set to blow forward and toward the feet.
110
Share

How to Deal with Dull Spray Paint?

Repaint the car with a high-quality, more glossy automotive paint; or use crystal coating to make the car look shinier. Additionally, you can wax the car paint to enhance its gloss and brightness. Below are specific details about crystal coating: 1. Introduction to Crystal Coating: Crystal coating is a hard protective layer specifically designed for key areas of a car, such as the paint surface, glass, tires, rims, seats, engine, interior, and exterior trim. The materials used in crystal coating mainly include polysiloxane, polysilazane, and inorganic silicon. 2. Post-Coating Precautions: Do not wash the car within a week after crystal coating. The coating agent takes 24 hours to fully bond with the car paint, forming the final crystalline protective layer. After 4 to 6 months of crystal coating, you can visit a car beauty shop for paint surface restoration to optimize the coating effect and prolong its durability. Avoid touching the painted surface after crystal coating to prevent affecting the final result.
112
Share

What are the differences between Bridgestone T005A and ER33?

The differences between Bridgestone T005A and ER33: 1. Different tread designs: The T005A has deeper tread grooves, offering outstanding performance in wet conditions; the ER33 features more varied tread patterns, providing better overall performance. 2. Different positioning: The T005A is positioned for luxury sedans, emphasizing grip, wet-road braking performance, and enhanced durability; the ER33 is slightly lower in positioning, leaning towards sporty characteristics, focusing on handling and comfort. 3. Different pricing: The T005A is generally priced higher, targeting comfort with superior overall performance; the ER33 is more economical, focusing on low rolling resistance, which can effectively reduce fuel consumption over long-term use.
113
Share

How to Turn on the Seat Ventilation in BYD Han?

There is a switch with a fan symbol under the seat. Press this switch to activate the seat ventilation function. The seat ventilation function is connected to the air conditioning system. When the air conditioning is turned on, the seat ventilation function will automatically activate.
107
Share

How to Change the Automatic Transmission Fluid for Changan CS35?

First, completely drain all the fluid from the oil pan, then pour in the same amount of new fluid. Remove the outlet pipe and use an air tank to blow air, allowing the fluid to flow back into the transmission. Connect a tube to the fluid pipe interface, start the engine, and switch between D and R gears, running for 5 to 10 minutes. During this circulation process, the fluid will be pumped out through the tube. When the new fluid color appears, turn off the engine. While the transmission is pumping out the fluid, add new fluid through the funnel, and finally remove the tube.
117
Share

What to Do When the Reverse Camera Shows No Signal?

Reverse camera showing no signal is usually caused by poor line contact. It is necessary to promptly check the wiring and the connection points with the vehicle installation to see if there is any loose connection. Below is relevant information about the reverse camera display: 1. Camera installation position: The camera is located above the rear license plate. The camera's shooting range is very limited and cannot capture objects near corners or under the bumper. The displayed image may vary depending on the vehicle's direction or road conditions, and the distance shown on the screen may differ from the actual distance. 2. Reverse trajectory lines: The reverse distance auxiliary lines are divided into three parts: red, yellow, and green. They respectively indicate the distance range of obstacles from the bumper, as follows: Red: 20 cm 50 cm; Yellow: 50 cm 150 cm; Green: 150 cm~300 cm.
105
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.