How to Reset the Maintenance Light on a 2019 Great Wall Wingle 5?

[MakaylaDella]

Turn on the ignition switch without starting the engine, simply rotate the switch to the "NO" position. Press the button on the instrument panel to switch the display to the instantaneous fuel consumption mode, then turn off the ignition switch. Press and hold the mode button on the instrument panel, turn the ignition switch to the "NO" position, and then release the mode button. Simultaneously press the "Mode" button and the left "Time Adjustment" button on the instrument panel, and the maintenance light will reset to zero.

[VonBradley]

I've been driving my 2019 Great Wall Wingle 5 for a while now, and clearing the maintenance light is actually quite easy, just like when I encountered it last time. Here's how to do it: First, turn off the engine and make sure the ignition switch is completely off; then press and hold the trip reset button on the dashboard; at the same time, turn the key to the ACC or ON position without starting the engine; hold for about 5 to 10 seconds, and the maintenance light will automatically go off. Remember to release the button as soon as the light goes off to avoid damaging it by holding it too long. This operation essentially resets the reminder system to prevent the light from coming on again before the next maintenance. The maintenance light usually comes on to indicate that it's time for an oil change or routine maintenance, so don't ignore it. Regular oil changes can reduce engine wear and extend the life of your vehicle. If the light doesn't go off, it might be due to a blown fuse or a sensor issue—it's best to have it checked by a professional shop rather than trying to force it. Safety always comes first when driving.

[DiElliot]

To clear the maintenance light on a 2019 Great Wall Wingle 5, follow these three simple steps: First, turn off the ignition switch and let the vehicle sit idle. Second, press and hold the trip button on the dashboard without releasing it. Third, turn the key to the ON position, and the dashboard will light up; wait a few seconds until the maintenance light goes out. The entire process takes no more than half a minute and is super easy. The maintenance light is designed as a thoughtful reminder—don't skip important maintenance like oil changes just to save money. It's recommended to reset the light immediately after each service to ensure accurate reminders next time. On a related note, the maintenance interval for the Wingle 5 is typically between 5,000 to 10,000 kilometers, and adjusting it based on road conditions is even better. If the light goes out but keeps flashing, check for any short circuits, and if the issue persists, seek professional help at a 4S shop.

[McJesse]

As a new car owner, I panicked when the maintenance light first came on in my 2019 Great Wall Wingle 5. Here's the reset method I learned: After the vehicle is completely turned off, press and hold the small button on the instrument panel; simultaneously turn the key to the ACC position; wait about 5 seconds, and the light will disappear. This operation is similar to performing a soft reboot on the vehicle and doesn't affect any data. The maintenance light comes on for safety reasons, reminding us to change the oil or filters on time. After resetting, don't forget the actual maintenance. Protecting the engine helps the vehicle last longer.

[Joan]

The maintenance light reset for the 2019 Fengjun 5 is very simple. Turn off the engine, hold the dashboard button; turn the key to ACC; keep it pressed for a few seconds until the light goes off. Don't rush or panic, just follow the steps. Also, a reminder to everyone: the maintenance light is not just for decoration, ignoring it may lead to car problems, such as insufficient oil damaging the engine. Regular maintenance at the shop is more reassuring.

[DelLola]

I often help friends with car issues, like resetting the maintenance light on a 2019 Great Wall Wingle 5. The key is coordinating the dashboard button and the ignition key: after turning off the engine, hold down the button, turn the key to the ON position, and wait about 5 to 10 seconds for the light to reset and go off. This process won't harm the car. The maintenance light indicates it's time for service. Let's talk about why it's important: regular maintenance, such as changing the oil, can prevent engine failures and save money on long-term repairs. It's good to develop this habit.