How to Replace the Wiper Motor on Wuling Hongguang?

[OFrancisco]

Open the front engine cover, first remove the two wipers using an Allen wrench. After removing the wipers, proceed to remove the decorative panel. There are two plastic clips—handle with care as they are fragile components. Once the decorative panel is lifted, the wiper assembly will be exposed. Remove the screws and then disconnect the power cable. Install the new motor onto the linkage, ensuring the linkage is perfectly aligned and the screws are tightly fastened. Reassemble the wiper assembly by following the disassembly steps in reverse order.

[CalvinMarie]

I previously replaced the wiper motor on my Wuling Hongguang, and although the task was a bit challenging, I found it quite enjoyable to do it myself. First, turn off the engine, remove the car key, and disconnect the negative terminal of the battery to prevent electric shock. Next, remove the cover of the wiper arm, loosen the fixing bolts with a wrench, and take it off. Then, inspect the wiper assembly cover, pry open the clips or unscrew the bolts to remove it, revealing the motor's position. Disconnect the wiring harness, then use a wrench to remove the three fixing bolts of the motor to take out the faulty one. When installing the new motor, clean the surrounding dust first, ensure the linkage isn’t misaligned, align the holes during installation, tighten the bolts, reconnect the harness, and finally reassemble all components. During testing, start the vehicle and turn on the wiper switch to check for smooth operation. The whole process takes about 30 minutes to an hour. After completing it, I remember to add some lubricant to the wiper system to extend its lifespan and prevent jamming. If you're not confident, spending some money to have a repair shop help is also an option, but DIY saves about 200 yuan in labor costs.

[DelGrace]

As a car enthusiast, I've gained some experience from replacing wiper motors several times myself. Before changing the Wuling Hongguang's motor, always ensure the car is turned off and the battery's negative terminal is disconnected to avoid danger. Briefly, the steps are: first remove the protective covers of the two wiper arms, unscrew and move the arm rods to expose the assembly. Then disconnect the wiper motor's connector and remove a few fixing bolts to take out the faulty part. When installing the new motor, buy a matching model for about 100-150 RMB, preferably choosing original parts on Taobao or at a local auto parts store. Handle gently during installation to avoid damaging the circuit board. After completion, test it to observe if it operates normally without excessive noise. Additionally, I also check the wiper fluid and water lines to prevent blockages. Beginners should prepare a pair of gloves for hand protection; the tools needed are just a wrench and a screwdriver, making it easy to handle. The whole process costs around 150 RMB, cheaper than going to a shop, and it's quite practical for practice.

[ArianaFitz]

I've worked in car repairs for many years. When replacing the wiper motor, act decisively without delay. After cutting power, directly remove the wiper arm and take off the cover to access the core area. Disconnect the plug, remove the bolts, install the new one, and test it. A socket wrench and screwdriver are sufficient tools - the job can be done within 10 minutes. Most issues stem from aging or water ingress. The key is choosing quality parts to avoid inferior products.

[OAaron]

I've always worked on my car myself to save money, and replacing the Wuling's wiper motor was worth sharing. First, assess the cause of the motor failure—often due to excessive water exposure and aging. Bought a replacement part for 150 yuan and fixed it myself. Steps: remove the arm, clean the cover, disconnect the wiring, unbolt the old motor, install the new one, reassemble, and test the switch. Only needed a wrench and screwdriver, done in my home garage, saving 300 yuan in repair fees. During the process, I found the Wuling's structure simple, making DIY easy for beginners. Afterwards, I recommend regular cleaning of the wiper system to prevent corrosion.

[LeGrace]

I believe replacing the wiper motor prioritizes safety as impaired visibility is dangerous. Preparations: Wear gloves and goggles, disconnect the battery to ensure zero risk. During the process, first remove the wiper arm carefully to avoid scratching the paint, then take off the assembly cover to access the motor area. Disconnect the wiring, be cautious of static electricity, then use tools to remove the bolts and take out the motor. Clean the area before installing the new part. During testing, ensure smooth operation without vibrations. I also checked the wiper linkage for any looseness to enhance the overall system's durability. The entire process costs around 140 yuan for parts, making it both cost-effective and hassle-free.