···
Log in / Register

How to Remove the Small Wrench Icon on the Arrizo 5 Dashboard?

6Answers
MacArcher
07/28/2025, 02:49:19 AM

Method to remove the small wrench icon on the Arrizo 5 dashboard: 1. Ensure the vehicle is turned off; 2. Locate the menu toggle button on the steering wheel; 3. Press and hold the toggle button without releasing; 4. Press and hold the one-touch start button for 3 seconds until the vehicle powers on and begins self-inspection (all warning lights will illuminate, which is normal); 5. Wait for the self-inspection to complete while keeping the toggle button pressed. After approximately 5 seconds, the small wrench icon will disappear. The Arrizo 5 is a sedan produced by Chery, measuring 4572mm in length, 1825mm in width, and 1482mm in height. It adopts the Arrizo series' family-style exterior design with sportier detailing, along with upgraded interior and configurations. It is equipped with a 1.5L naturally aspirated engine or 1.2T/1.5T turbocharged engines, featuring a three-spoke sport steering wheel integrated with multiple shortcut buttons.

Was this review help?
103
Share
DiDavid
08/11/2025, 10:40:26 AM

I remember dealing with the little wrench on the Arrizo 5 dashboard was quite simple. This little wrench is a maintenance reminder light, usually appearing automatically after the car has been driven for 5,000 or 10,000 kilometers. To reset it, I usually sit in the driver's seat, turn the key to the ON position without starting the engine, then press and hold the reset button next to the dashboard or the mode switch button on the steering wheel for about five seconds. When I see the little wrench flash a few times, it disappears. If the car is relatively new or has setup issues, it might take a few attempts, or you may need to refer to the owner's manual to confirm the button combination. Sometimes, after resetting it yourself, if the maintenance isn't done on time, it will reappear. It's recommended to regularly check the oil and brakes to avoid neglecting important maintenance and prevent minor issues from becoming major problems, ensuring a worry-free driving experience.

Was this review help?
12
Share
Expand All
LaGrace
09/27/2025, 04:34:30 AM

When I drove my Arrizo 5, I encountered this small wrench icon. The reset process is actually quite simple. Before starting the engine, turn the key to power on until the dashboard lights up, then locate the menu button on the left side of the steering wheel or the small button on the instrument panel. Press and hold it for a few seconds until the wrench icon disappears. It's as simple as resetting a computer. However, I've found that if the button operation isn't done properly, such as pressing for too short a time, the system might not respond. In that case, it's better to visit a 4S shop to have it adjusted with professional tools. The maintenance reminder is well-intentioned—it alerts you when it's time to change the oil, preventing engine wear. Developing the habit of regular maintenance ensures your car runs more smoothly.

Was this review help?
18
Share
Expand All
Abel
11/10/2025, 10:46:03 PM

Removing the wrench icon on the Arrizo 5 is quite simple: Make sure the vehicle is not started, then press and hold the button combination on the dashboard or steering wheel for about five seconds in the ON position. This method works in most cases. If it doesn't, consult the manual or contact a service center - avoid random operations that might affect the system. Regular maintenance is key.

Was this review help?
10
Share
Expand All
JoshuaFitz
01/01/2026, 12:32:57 AM

I've dealt with this icon before. The reset steps are: turn the key to ON, then press and hold the reset button for five seconds until the wrench light turns off. Be careful not to accidentally activate other settings, especially when dealing with complex electronic systems. It's best to perform regular maintenance checks, such as changing the oil and filters, so the wrench light doesn't come on frequently, making the car more reliable to drive.

Was this review help?
15
Share
Expand All
LaLyla
03/29/2026, 01:54:09 AM

The small wrench on the Arrizo 5 is a maintenance reminder. I recommend holding down the instrument panel button for a few seconds in the ON state to clear it. This is equivalent to resetting the computer counter, ensuring the operation is correct to avoid errors. With timely maintenance, the small wrench appears less frequently, which helps extend the vehicle's lifespan.

Was this review help?
15
Share
Expand All
More Q&A

What are the differences between the new Magotan and the new Accord, and how to choose?

About the differences between the Magotan and the Accord are as follows: 1. Different body dimensions: The Magotan has a length, width, and height of 4865mm, 1832mm, and 1471mm respectively, with a wheelbase of 2871mm; the Accord has a length, width, and height of 4893mm, 1862mm, and 1449mm. 2. Exterior: The Magotan's exterior is mature, stable, and grand, giving a sense of safety and luxury; the Accord's exterior is more sporty. 3. Powertrain: The Magotan 1.5t is equipped with an EA211 engine with 186 horsepower, while the 2.0t version uses an EA888 engine, with the low-power version offering 186 horsepower and the high-power version offering 220 horsepower; the Accord is equipped with an Earth Dreams 1.5t engine, with the low-power version offering 177 horsepower and the high-power version offering 194 horsepower, while the hybrid version with a 2.0-liter engine offers 146 horsepower and a combined output of 210 horsepower. It is recommended that users choose between these two cars based on their personal needs.
104
Share

What engine is used in the Changan Yuexiang?

Changan Yuexiang engines are all equipped with domestically produced 472Q-16 valve electronically controlled multi-point fuel injection engines, so they belong to the category of domestic engines. The model of the Changan Yuexiang 1.5L naturally aspirated engine is JL473QF, with a maximum horsepower of 107 hp, a maximum power of 78.5 KW, a maximum power speed of 5500 rpm, and a maximum torque of 145 N.m. The model of the 1.4L naturally aspirated engine is JL473Q4, with a maximum horsepower of 101 hp, a maximum power of 74 KW, a maximum power speed of 6000 rpm, and a maximum torque of 135 N.m. For daily maintenance of the Changan Yuexiang engine, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected according to the mechanical load, with the selection standard not lower than the manufacturer's specified requirements; Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, the performance deteriorates, which can cause various problems for the engine. To avoid faults, oil should be changed regularly according to usage conditions, and the oil level should be kept moderate; When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is blocked and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to pass through the bypass valve and bringing contaminants back to the lubrication area, accelerating engine wear and increasing internal pollution; Regularly clean the crankcase. During engine operation, high-pressure unburned gas, acid, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and the cylinder wall, mixing with metal powder produced by part wear to form sludge. A small amount remains suspended in the oil, while a large amount precipitates, blocking the filter and oil holes, making engine lubrication difficult and causing wear; Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the normal operation of the engine but also extends the overall lifespan of the radiator and the engine.
102
Share

Are 7-seater vehicles in 2021 exempt from inspection for 6 years?

2021 7-seater vehicles are exempt from inspection for 6 years. Extended relevant information is as follows: I. Situations that cannot enjoy the exemption policy: 1. Minivans; 2. Vehicles that have been legally penalized for illegal modifications; 3. Vehicles involved in traffic accidents causing casualties; 4. Vehicles that have not completed registration procedures for more than 4 years since the date of manufacture are not eligible for the 6-year exemption policy. II. After exceeding 6 years, the annual inspection cycle for 7-seater vehicles is: 1. More than 6 years but less than 10 years, only requiring 2 online inspections, specifically in the 6th and 8th years. 2. More than 10 years, inspected once a year; more than 15 years, inspected every six months.
115
Share

Where is Great Wall Lubricant produced?

Great Wall Lubricant is a lubricant brand under Sinopec. It has 11 branches located in Beijing, Shanghai, Tianjin, Chongqing, Maoming in Guangdong, Wuhan and Jingmen in Hubei, Jinan in Shandong, and Zhengzhou in Henan. Here are specific details about Great Wall Lubricant: 1. Company Profile: Great Wall Lubricant is a specialized lubricant company established by Sinopec to adapt to the international competition in the lubricant market. It integrates lubricant production, research and development, storage and transportation, sales, and service, making it the largest and internationally leading lubricant production and sales group in Asia. The company's predecessor was an enterprise under the former Ministry of Petroleum Industry, which made significant contributions to the launch of China's 'Two Bombs and One Satellite' project. In the early 1980s, Sinopec pioneered the first brand in China's lubricant industry—'Great Wall,' characterized by aerospace lubrication technology, supporting the development of China's manufacturing industry and serving the general public. 2. Brand Development: Great Wall Lubricant is a Chinese brand that best combines localization and internationalization. In terms of technology and quality, it matches international brands by adopting international standards and developing differentiated new products. In the domestic market, Great Wall Lubricant conducts unique research on Chinese consumers and machinery equipment, providing better lubrication solutions through integrated production, sales, and research operations.
118
Share

What do R, N, and D gears mean?

The meanings of R, N, and D gears are as follows: 1. R (Reverse) gear: Used for reversing. Unlike manual transmission cars, automatic transmission cars cannot use the semi-clutch technique, so special attention should be paid to the control of the accelerator pedal when reversing. Usually, you need to press the safety button on the shift lever to move it to the "R" position. 2. N (Neutral) gear: N stands for Neutral, which can be used when starting, towing, or during temporary stops (e.g., at a red light). To prevent the vehicle from rolling on a slope, always apply the brake when in Neutral. When the shift lever is in the "N" position, the power between the engine and the transmission is cut off. 3. D (Drive) gear: Also known as the driving gear, this position is used for normal road driving. In the D position, the transmission automatically shifts between 1st and overdrive gears (equivalent to 1st to 4th gears) based on speed and throttle conditions.
101
Share

Is the 'i' the intake valve or the exhaust valve?

i is the intake valve. The intake valve is part of the engine's valve train, and without the valve train, the engine cannot operate properly. Principle of the intake valve: The throttle control mechanism of a traditional engine operates via a cable (soft steel wire) or a rod, with one end connected to the accelerator pedal and the other end connected to the throttle linkage plate. Electronic throttle systems primarily use a throttle position sensor to control the opening angle of the throttle based on the engine's required energy, thereby regulating the amount of intake air. Consequences of intake valve damage: If the intake valve is damaged, the piston may also be damaged. After an engine experiences valve damage, both the intake valve and the piston need to be replaced. Replacing the valve and piston requires opening the engine's cylinder head and removing the connecting rod and piston. Some car engines use timing chains, so it is essential to replace the timing belt regularly during vehicle use. Over time, the timing chain may stretch, which can lead to the chain skipping teeth. If the timing chain skips teeth, it can result in reduced engine power and increased fuel consumption.
120
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.