How to Remove the Small Round Mirror on the Rearview Mirror?

[SanElisa]

The method to remove the small round mirror on the rearview mirror is as follows: First, soak the area where the adhesive of the small round mirror is attached with alcohol. Then, use a hairdryer on the hot air setting to blow on it. After blowing for a while, the small round mirror will come off. Any remaining adhesive can be gently wiped away with alcohol. Below is an introduction to the advantages and disadvantages of the small round mirror on the rearview mirror: 1. Advantages: It allows the driver to better observe the side of the car body and the rear wheels while seated in the car. If there is a vehicle in the blind spot, it can be detected in time, reducing the risk of accidents. 2. Disadvantages: No matter where the small round mirror is installed, it will affect the field of view of the rearview mirror.

[VonReed]

I previously installed a small convex mirror on my rearview mirror to expand my field of vision, but it wasn’t sticking firmly and even obstructed my view, so I decided to remove it. It was actually quite simple—I used a hairdryer at home to blow hot air onto the adhesive part on the back of the small mirror for about a minute or two to soften the glue. Then, I gently pried the edges loose with my fingers or a plastic scraper, being careful not to use too much force to avoid cracking the mirror. After removal, there was usually some residual adhesive left, so I wiped it clean with an alcohol wipe. When driving, it’s important to pay attention to the proper placement of these small accessories, as improper positioning can easily distract you. If the adhesive is particularly stubborn, you can apply heat a few more times or use a professional adhesive remover, but avoid pulling too hard to prevent damaging the rearview mirror—after all, repairs can be troublesome and costly. I recommend ensuring your car is parked safely before attempting any DIY work—safety first. Practicing these small skills can save you a lot of trips to the repair shop.

[Allie]

I found that the small blind-spot mirror was stuck quite tightly, so you need to be careful when removing it to avoid scratching the original mirror surface. I used a hairdryer to heat the adhesive to soften it, then peeled it off bit by bit with gentle movements—no rushing. If any residue remains, I usually clean it off with soapy water or cooking oil. This little gadget was originally meant to help with blind spots, but after removal, the visibility becomes much clearer, making driving more comfortable and safer. Remember to do this in a parking lot or at home—never while driving. Occasionally, such accessories can age and crack easily, so while checking, also inspect the rearview mirror's stability to prevent accidents. As for tools, a hairdryer works just fine—it’s hassle-free and doesn’t cost extra, making it ideal for routine maintenance.

[VanLilliana]

Once while driving, I noticed the small convex mirror was tilted and affecting my vision, so I casually removed it. The process wasn't difficult—just soften the adhesive with hot air and slowly peel it off. After completion, clean the adhesive residue to keep the rearview mirror clean. Although small, these mirrors may peel off after prolonged use, so timely removal avoids driving risks. I quite enjoy tinkering with car accessories, often reminding myself not to cheap out on low-quality products, as strong adhesives can make removal difficult. With safety in mind, the car becomes more worry-free.

[JasonMarie]

The key to removing the small round mirror from the rearview mirror is dealing with the adhesive part, as it uses strong double-sided tape. I tried using a hairdryer to soften the adhesive and then slowly peeled it off. After removal, wipe away any sticky residue, avoiding sharp tools to prevent scratching the mirror surface. The small round mirror was originally intended to reduce blind spots, but after removal, consider upgrading to a more reliable blind spot assist system. I always choose overcast days for this operation, as the adhesive is easier to control when warm, saving time and protecting the car's structure. Occasionally check the overall fixation to prevent loosening issues.

[PiperDella]

The method I use to remove small round mirrors is to heat the adhesive with a hair dryer to soften it, then carefully peel it off by hand to avoid scratching the rearview mirror. After removal, clean any residual adhesive to maintain a clear view. The original intention of installing these mirrors was to assist with visibility, but after removal, driving becomes more focused. During the operation, tools like alcohol for cleaning can be used for simple and efficient removal. I often check during maintenance to ensure all details for safe driving are in place.