How to Remove the Side Mirror Cover of the 10th Generation Civic?

[Kinsley]

Process the mirror glass by pressing the head of the glass with your hand to lift the tail, then grab the tail and pull it outward firmly to remove the glass. After removing the glass, if the mirror has a heating function, you also need to unplug the wire connector of the heating pad. Locate and remove the screws along the edges. After unscrewing and removing all the fixing screws, the central component can be taken out, and the mirror removal is essentially complete.

[DeAubrey]

I recently disassembled the mirror housing of a 10th-gen Civic, and the process went relatively smoothly. First, adjust the mirror glass to its lowest position to expose the edge gaps. Use your fingers or a plastic pry tool to gently pry from the inner edge of the glass, releasing three clips along the edge to remove the glass. Be careful not to scratch the mirror surface with metal tools. After removing the glass, you'll see three fixing screws on the housing—use a Phillips screwdriver to remove them one by one. Next, deal with the plastic clips on the housing by starting to pry from below the mirror base, gradually releasing all the clips. Before pulling off the housing, remember to disconnect the turn signal wiring harness by pressing the clip to separate it. The entire operation requires gentleness, as plastic parts are brittle and prone to breaking. Wearing gloves is recommended to prevent cuts, and storing screws in a small box after removal helps avoid losing them. Reassembly is the reverse process, but ensure all clips are securely fastened to prevent gaps in the housing. Finally, test the power adjustment and turn signals before finishing up.

[Marie]

I've got some solid tips for removing the mirror housing on a 10th-gen Civic. The key is mirror glass removal - best done with a dedicated plastic pry tool. After adjusting the mirror to its lowest position, insert the pry tool at the edge clip and lift upward gently, avoiding brute force. Once the glass is off, use a magnetic screwdriver for the three screws to prevent dropping them. The housing's tightest clips are at the bottom - briefly heat with a hair dryer to soften the plastic before prying. When installing the new housing, pay special attention to aligning the turn signal wiring connector (it won't fit if reversed). Avoid working under direct sunlight as heat makes plastic brittle. Take pre-disassembly photos of clip positions to ensure proper reassembly. Basic tools like plastic pry tools, Phillips screwdriver and hair dryer are sufficient - no need for special tools. Budget about 30 minutes, with extra time recommended for beginners.

[OAshlyn]

Removing the mirror housing on the 10th-gen Civic is actually quite simple. First, adjust the mirror to its lowest position to expose the clips, then use your fingers to push upwards from the inner edge of the mirror to remove it. Next, unscrew the three screws and use your fingernail or a plastic tool to release the clips on the housing. Pay special attention to pressing the small clip when disconnecting the turn signal wiring. Always use plastic tools during the process to avoid scratching the paint. After reassembly, remember to test if the heating function works properly.

[DiElena]

I just disassembled the Civic mirror housing yesterday. After adjusting the mirror to the lowest position, I slowly pried open the clips from the edge using an old credit card. After removing the mirror, I saw three screws and took them out with a Phillips screwdriver. Starting to unclip the housing from the bottom is the most effortless way—don't pull it hard. Be careful when unplugging the turn signal connector, and don't lose the waterproof rubber gasket. It's recommended to work with two people: one holds the mirror frame while the other removes the housing for better stability. Wear gloves throughout the process to prevent static electricity, as dust on plastic parts can affect installation. Make sure the clips are aligned properly and you hear a 'click' sound for proper installation, and remember to check the evenness of the gaps afterwards. Beginners should allow about 1 hour for the job.

[AllieFitz]

As someone who frequently modifies Civics, I recommend buying a set of new clips as backup before removing the mirror cover. Adjust the mirror to its lowest position and evenly apply force along the frame to pry it off. After removing the three screws, focus on the hidden clip at the base—it's the most challenging to remove. Before painting or installing a carbon fiber cover, thoroughly clean the grooves in the base; dust can prevent a tight fit. When installing the new cover, first connect the turn signal plug, then secure the position—pressing from the bottom up is the safest. After modification, be careful not to pinch the heating wires when adjusting the mirror; you won’t notice the issue until winter. All you need are a plastic pry tool and a Phillips screwdriver—it’s a 10-minute job.