How to Remove the Maintenance Reminder on the Haval H6 Dashboard?

[DelEvangeline]

Haval H6 maintenance reminder elimination method: Turn off the key, press and hold the button at the lower right of the dashboard; turn the key to the position where all dashboard lights are on, and release the button after the small wrench icon on the dashboard stops flashing; press the button at the lower left of the dashboard, and the small wrench will disappear, thus eliminating the maintenance reminder. Relevant information about the Haval H6 is as follows: 1. The Haval H6's body dimensions are: length 4653mm, width 1886mm, height 1730mm, with a wheelbase of 2738mm. 2. The Haval H6 features a MacPherson strut front suspension and a multi-link independent rear suspension, equipped with a 2.0T turbocharged engine, delivering a maximum horsepower of 211PS, maximum power of 155kW, maximum torque of 325Nm, paired with a 7-speed dual-clutch transmission.

[OLaura]

I also encountered the situation where the maintenance light on my Haval H6 was on last time, and it was quite simple to reset it myself. First, don't start the engine, just power on to light up the dashboard. Then, press and hold the menu button on the left control key of the steering wheel to navigate to the vehicle information section. Find the maintenance reminder page, and you'll see a reset option. At this point, you need to press and hold the OK button for more than five seconds. Make sure to keep your finger steady, release it when you hear the prompt sound, and check if the small wrench icon on the dashboard disappears—that means it's successful. The key is not to hold it for too short a time; the first time I tried, I was too hasty and didn't reset it successfully. I recommend recording the steps with a video for future reference—it'll make the process even easier next time.

[Matilda]

When it comes to resetting the maintenance reminder for the Haval H6, I've studied the operational differences between the new and old models. For older models like those before 2020, you basically need to go to a 4S shop to clear the code with a computer. Newer models like the third-generation H6 can be operated manually. Specifically, after powering on, find the steering wheel buttons and enter the vehicle status menu in the settings. On the maintenance reminder page, press and hold the confirm button until you see the mileage count restart from 0. It's important to reset only after changing the engine oil, otherwise the new maintenance cycle will be messed up. Additionally, if you drive a lot on dirt roads, it's normal for the maintenance reminder to light up early. Don't rush to reset it; it's safer to check the chassis first.

[VonAlana]

I always keep the Haval manual in my car, and referring to it is the most reliable way to reset the maintenance reminder. The steps are quite clear: first, turn the ignition to the ON position, use the buttons on the right side of the steering wheel to enter the menu, select the trip computer interface, and then long-press the selection button. The new system has a sliding confirmation bar that must be slid to the end to complete the reset. Once, when it was cold and the touch screen was unresponsive, I succeeded by operating it with thin gloves. After resetting, remember to record the current mileage to estimate the next maintenance time. If the reset fails three times in a row, it might be a sensor malfunction, and you should visit a service center.

[DelSabrina]

As a car owner, I'd like to remind you to confirm the maintenance was actually performed before resetting. I've seen cases where people reset directly and ended up damaging the engine due to overdue oil changes. The operation is actually quite simple: after powering on, use the steering wheel buttons to enter the settings menu and locate the vehicle maintenance information section. For newer touchscreen models, simply tap the reset button. For mechanical button models, press and hold the confirmation button for more than five seconds. Watch for the dashboard numbers to flash during the hold to ensure it's effective. After resetting, start the vehicle and take a short drive to confirm the warning light has completely disappeared for added safety.

[DelCharlotte]

I noticed significant differences in the reset procedures for different model years of the H6. My 2021 model requires submenu operations. Detailed steps: Press the start button twice to power on, use the menu button on the left side of the steering wheel to enter the vehicle status page, then right-click to switch to the maintenance page. At this point, simultaneously hold the return button and OK button for seven seconds until you hear the prompt tone change, indicating success. The tricky part is precise timing - it's best to use a phone stopwatch for assistance. Avoid operating on bumpy roads to prevent accidental activation of other functions. After a successful reset, the next maintenance reminder will be more accurate, giving you better control over your vehicle's condition.